I am having problems configuring airport express with time capsule

Hi,
I am having problems setting up airport express (old version) with time capsule. It was working perfectly fine with my old router, Airport Extreme (b/g).
I have tried to reset the Airport Express, and now I am having problems finding it in my personal networks. Not too sure what exactly is going on, other than it was working less than a day ago, and now I can't even locate it on the network to configure.
Anyone have any suggestions? I have already tried a hard reset, and no luck so far.

There are 3 types of resets.
1. Soft
2. Hard
3. Factory
Try a factory reset.
http://docs.info.apple.com/article.html?artnum=108044
Joseph Kriz

Similar Messages

Airport Express with Time Capsule - Stronger Signal, No Increase in Speed

I just added an Airport Express to extend my network from a Time Capsule. Pretty sure I set it up right (extend the network selected in Airport Express, allow the network to be extended in Time Capsule). I get the green light and do get a stronger signal in the far reaches of my house where before I added the Airport Express there was almost no signal. The Time Capsule is in bridge mode connected to a Verizon FIOS router doing the DHCP, NAT, etc. The problem is, there is still less than 1Mbps with the Airport Express, even though the signal strength is 80+%. I have moved it around to different locations without much effect. I would think that with the green light, a stronger signal, and the fact that I can connect (although at low speed), I have it working, but the throughput is terrible. Does extending the network (non-WDS) with the Airport Express cause a significant slowdown? Is there any way to boost the signal from the Time Capsule (power, external antenna, etc.)? Moving it is not an viable option. Thanks in advance.

Having a strong signal does not necessarily equate to a usable signal. It may be that there is significant wireless interference and the data packets are being affected and reducing the bandwidth.

Airport Express with Time Capsule: How does it work?

I don't know much about newtorking but wanted to ask this:
I am considering buying a 1tb Time Capsule. I use Airport Express now so I can stream iTunes to my home entertainment system. Is the configuration supposed to be this? See below:
-Plug the Time Capsule into the cable modem for internet access
-Plug the APE into the Time Capsule with (ethernet? USB?) to power its Air Tunes capabilities
I would love to gain the back up and simplicity of Time Capsule but I am not giving up Air Tunes.
Any replies appreciated. Thanks.

So it sounds like I should just leave Airport Express as my networking hub/internet connection point, and let Time Capsule acquire a spot on the network, then I can access it that way.
I guess I thought that Time Capsule had to be the primary router/internet connection for the network, and Airport Express would become sub to that.
I think I prefer the first option over my idea.
Thanks for the response.

Extend Airport Express with Time Capsule? So just one Wi-Fi network in my house ? Possible?

Hi!
I did Google and try to get it working at home - but I can't get it to work. I want to be able to walk in my house without my iPhone/iPad loosing the Wi-Fi signal because now there is downstairs and a upstairs wi-fi network.
So the thing I want is.. I got a Airport Express on the ground floor which is for my Wi-Fi network there.
On my 2nd floor I want my Time Capsule to extend this network - so that my iPhone picks that Wi-Fi up straight away. Now when I am upstairs my iPhone is still connected to the wi-fi from downstairs (which it can't reach) and so I am not connected. Which results in me having to manually switch to the upstairs network..
My question : Is it possible to setup a Wi-Fi network downstairs and have my Time Capsule repeat it (so not a new network) for upstairs use?
Hope someone can help me and this is possible!
Thnx in advance!

Welcome to the Apple Support Communities
That's possible. See > http://support.apple.com/kb/HT4145

Airport Express with Time Capsule - Nowhere near 802.11n speeds!

I currently have a Time Capsule set up in bridge mode, giving me a wired+wireless network off my Belkin modem. I just bought an Airport Express to serve as a wireless bridge (to connect my wired PC to the network) but transferring files across the APE-TC connection goes at a woefully slow 3-4MB/s! (When I connect my 802.11n laptop to the TC directly via wireless, it was 3-4x faster.)
This problem happens whether the TC is set to either create a second discrete 5GHz network or not. I noticed that if I run this separate 5GHz network, and I connect the APE to the 2.4GHz one manually, the transfer speed slows to 1-2MB/s.
How do I get it to go faster? The APE and TC are only about 5m apart (+ 1 wall).

Welcome to the discussions!
+What to do?+
The iPhone does tend to remember the router that it is originally connected to.
If you plan to use the iPhone most of the time when you are in proximity of the AirPort Express, I suggest that you delete the current WiFi connection on the iPhone, restart the device, locate it near the AirPort Express, and set up a new connection to your network.
Works for me. May or may not work for you.

Airport Express with Time Capsule

Hi
I am attempting to create the following setup and would like advice as to the best way to go about it:
In my house I have a Time Capsule connected to an incoming internet connection (from a cable modem) creating a WiFi network
I have a 'home office' at the end of the garden and have taken one ethernet output from the back of the TC and extended that to the office using a couple of TP Link Powerline adapters
The intention is to connect an Airport Express in the office connected to the TP Link adapter to create a WiFi network for the office
How should I set up the TC and AE to make this work? I have tried a few things using Airport Utility but no joy yet!
Many thanks in advance
PS Wasn't sure whether to post this here or in the TC discussion group so I have copied it there also.

Hi Bob (and everyone else)
Firstly - sorry about the tardy response! I should have known that the winter holiday would interrupt my train of thought on this - but thanks for your suggestions. So:
I have checked the powerline connection - no problem there (using it to connect by cable as I write)
I then tried the following:
I set up AE to extend the wireless connection network as suggested. The AE works fine while in wireless range of the TC. When connected by cable to the powerline adapter in the office it does not, presumably as the office is out of wireless range of the TC??
Alternatively if I am to set up the AE to create a new wireless network, how should I do that so that IP addresses/DHCP etc does not cause conflict?
Many thanks

Using Airport Express with Time Capsule

Simple question. We use Time Capsule primarily for WIFI. I have an express and want to use it only for playing my itunes music through our stereo. My Time Capsule works beautifully, but the express flashes amber when I connect it to a power source and our stereo. How do I get the two to work together simply. I don't care about extending our network or anything fancy. I just want to listen to good music.

You'll need to "hard reset" the AirPort Express by holding in the reset button until you see the amber light start to blink more quickly. Release the reset button when you see this occur.
Temporarily, position the AirPort Express near the Time Capsule and connect an ethernet cable from your Mac to the AirPort Express. Then open AirPort Utility and click Configure to follow the guided setup process. When asked how you want to configure the Express, you will choose the "Join a wireless network" option.
After you have completed the setup and updated the Express to save your new settings, you can disconnect the ethernet cable and move the AirPort Express to the desired location.

IPhone 4 802.11n and Airport Express with Time Capsule

I have a Time Capsule as my main wireless router, extended by an Airport Express (both are latest versions of the hardware and software). The Time Capsule is a dual-band version (2.4 and 5 GHz).
My new iPhone 4, which is supposed to be 802.11n 2.4 GHz compatible (unlike the iPhone 3Gx models) connects to the Time Capsule, but not to the Airport Express - hence no cover in certain parts of the home. There are no options for frequency when you extend a network - it's mostly plug and play from the main wireless router (the Time Capsule). What to do?

Welcome to the discussions!
+What to do?+
The iPhone does tend to remember the router that it is originally connected to.
If you plan to use the iPhone most of the time when you are in proximity of the AirPort Express, I suggest that you delete the current WiFi connection on the iPhone, restart the device, locate it near the AirPort Express, and set up a new connection to your network.
Works for me. May or may not work for you.

Airport express and time capsule config?

I have an airport express for Wi-Fi internet and printing. I have purchased a time capsule as a back -up drive to work with time machine. Should I
set it up seperately from the airport express or
replace airport express with time capsule ?
What's the best config and can I retqin existing netwrok ID and password?
Thanks for pointing me in right direction.

Hi Yoreilly:
i'm not sure just what setup is right for you. and i'm sure the newer Airport Express is way improved over mine (got mine few yrs ago). but my Airport express works as extension from your Time Cap Wi-Fi. Airport does not put out wireless Wi-Fi signal on it's own.
1> if yours can take your phone line & send out Wi-fi signal on it's own, then more power to you/ & you could sell back your Time Cap & just have a WD backup drive, or seagate external drive for less.
2> otherwise, your airport express needs to connect to your Time Cap, to answer you #2.
3> usually the application helps where you have dead spots in your house, or your location of Time Cap can't reach places in your house where U need Wi-Fi signal, or where you can't thread an ethernet cable out to your printer or device.
not sure how you are setup with your wireless printer now. but if your setup allows you to print by only using the Airport Exp, sure you can use the TimeCap separately as it's own Back-up drive. the thing is it has Wi-fi capability that you wouldn't be using with that setup.
hope this helps, & didn't confuse,
m

Configure airport express with mac book air

I am trying to configure airport express with a Mac Book Air, without success; the program is installed, but then, nothing appears to configure Airpor Express...
Can I get any help? Thank you
António

Hello!
I´m sorry it took so long to reply, but I´m new to these blogs; and I´ve been travelling a lot... Anyway, I was able to configure Airport Express, but I was told I could use it to expand my wireless network inside my house; which I found it´s not possible.
So, I´m returning my Airport Express to the store tomorrow and try to figure out a way to extend my wireless in any other way.
Any sugestion? Big houses are a problem...
Best regards, and once again thank you!
Antonio

Can't configure airport express with laptop after 10.5.6 update

I can't configure airport express with laptop after 10.5.6 update
the airport express is seen but can't access configuration screen, I get the spinning wheel forever.
Other computer gets to the configuration screen without problem.
And the airport utility describes the airport express like this: syAP.802.11format

I downloaded the airport utility and re-installed
and the problem was solved

Conflicts with Airport Express and Time Capsule

I am using Airport Express and Time Capsule at the same time. Connection to the web is via a router. Very often I do have conflicts. How shall I connect the gadgets? At the moment I connect the router to Airport Express (network cable).
Time machine back up doesn't work properly.
Is there anybody able to help me?
Regards

What broadband type do you have?
It can be impossible to plug a TC into the existing connection because the virgin media router has special setup or logins which are not revealed to end users.
If it is a fibre connection for instance the TC may simply not work. They have issues with many fibre ISP putting the gateway address outside the subnet of the main public IP.. (don't worry if it is too technical .. it amounts to .. it don't work! )
You may need to wait until Sat.
Get in a big supply of home videos or something and try and starve off your addiction.

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network?

How do I add an Airport Extreme with Time Capsule to an existing non-Apple network? I have an ISP provided wireless Router that has to remain as the base station. I am able to join my 1/2TB Airport Extreme and Airport Express to the network, but I can't access/use Time Machine.

One option would be to connect the Time Capsule (TC) to the ISP-provided wireless router by Ethernet. You can then configure the for a roaming network. Then, depending on what your goal is for the AirPort Express, you can either: 1) Add it to roaming network, 2) Configure the TC & the Express for an "extended" network, or 3) Configure the Express to "join" the roaming network for AirPlay.

Best way to extend wireless via airport express and time capsule

best way to extend wireless via airport express and time capsule
i live in a two storey house where i use my airport express to create a wireless network in the main floor, and time capsule to extend it in the upper floor, where my room is. i have like 16 mbps in the main floor, and 2-3 mbps in the upper floor after having speediest.
i used time capsule in the upper floor because i use wireless backup daily and don't want to put internet down while i im doin it and consequently my parent can have internet access in the main floor, am i right? or do i have make just the opposite in order to have a good internet speed?
secondly, while checking airport express wireless mode on airport utility, there is like 4 different type of radio mode(802 11n bg comp, 802 11n 2.4, 802 11n a comp, 802 11n 5ghz) which i have no idea what they mean
what do you recommend?
we have like iphone4, iphone 3g, mbookpro, ipad, ipad 2, samsung tv and a sony vaio laptop in the wireless network
thank you

What you have would appear to be working but I can comment how I would redefine your setup. Note that both Airport Express and Time Capsule can function as wireless base stations so you do have wireless everywhere and at all times — using the Time Capsules for backups doesn’t mean your parents won’t have internet access regardless of the where the base stations are located.
You appear to have devices to connect to your network that use the 2.4 GHz band with 802.11g such as the iPhone 3G and perhaps the 5 GHz band with 802.11n such as likely the Macbook Pro if it’s a recent model. The iPhone 4 can use 5 GHz and 802.11n. Can’t comment on the Sony and Samsung but you can check their specs.
Now the Time Capsule (if it’s a recent version), can simultaneously supply 2.4 GHz and 5 GHz band signals, but the Airport Express (if it’s recent) can only use one of those bands at one time. Likely the lowest common denominator for your devices is going to be the 2.4 GHz band since the devices that are capable of using 5 GHZ also support 2.4 GHz. If you don’t use 5 GHz, you won’t lose much in a two-storey home because likely it’s the 2.4 GHz band is better signal anyway because 5 GHz signals drop off quickly with several walls/floors to penetrate.
You also didn’t mention if the Airport Express is used to support a printer and/or AirPlay (using iTunes to play on remote speakers via the Airport Express connection) but that might also be a factor in the best location to place the Airport Express. Although the printer could be switched between the Time Capsule and the Airport Express if needed, only the Airport Express will support your remote speakers.
Recommend you use the Time Capsule as the Base station. When using Airport Utility to define the network, after you name your network, etc., select the Wireless tab, check the box “Allow this network to be extended” and set the Radio Mode to "802.11n (802.11b/g compatible)”.
Using the Airport Utility, click on the Airport Express; after you define the device and network name, select the Wireless tab, define the Wireless Mode as “Extend a Wireless Network” and check the box “Allow wireless clients”.
Hope that helps.

Cannot connect Airport Express to Time Capsule?

I had an existing wireless network with an Airport Extreme base that was extended with a first generation Airport Express. I replaced the Airport Extreme with Time Capsule because I needed the backup drive. Now I can't get the Express to integrate. When I try to bring it online, it brings everything down. I've reset it back to its defaults and am installing as if its new. The problem is that it brings everything else down. The two are connected via ethernet. For now I've had to take the Express offline until I can find a solution. Any advice?

Welcome to the discussions!
I don't have a solid answer yet to your issue, but would offer a few comments that might help sort things out.
I'm confused by your statement that you are able to extend the 2.4 GHz network, because the dual band TC does not allow the guest network to be extended. Check AirPort Utility - Manual Setup. Click the Wireless tab. I don't have a dual band TC, but I believe if you click the Options button, you will see more info about extending.
While there is a check box next to "Allow this network to be extended" for the main network, there is not a check box for the "Guest" network. It's not there, or least it's not there in the guide that I'm looking at.
I suspect that your computer was picking up the 2.4 GHz network from the TC, not from your Extreme. To verify this, open AirPort Utility again and click on Manual Setup for the TC. On the summary page, note the MAC address for wireless on the TC. Now, do the same thing for the Extreme.
Use your computer now to check things. Hold down the option key and click on the Airport icon at the top of the screen. The MAC address of the device that you are connected to will be displayed.
Have you tried to move the Extreme to a more remote location? You note that you have the two devices, TC and Extreme very close together. As a test, position the Extreme approximately half way between the TC and the area that you want to extend to and see if you can connect with your computer. Check to see if your computer is connecting to the Extreme or the TC by holding down the option key as above.
You have probably already done this, but check on the setup for the Extreme using AirPort Utility - Manual Setup - Wireless tab. There is a check box either on the Wireless page or the Options page to "Allow wireless clients". This must be checked for wireless clients to be able to connect to the the Extreme.
Post back with your findings and we'll try to figure this out.

I am having problems configuring airport express with time capsule

Similar Messages

Maybe you are looking for