I am loosing configuration when I power off my Cisco 857 router

I bought new Cisco 857 router from the shop. Router must have been used before as I couln't go in with default username/password cisco/cisco.
Well I followed instruciton and reset password to username and password. Now I finally connected to the Cisco CP express over my IE browser.
I found out that somebody was using a router from the shop so this is why I coun't log to it in the first place. Anyway problem is that when I changed configuration and applied settings it remembers it until I power it off. When I power it on again it remembers all settings from that shop.
It reverts everything back: IP address, previous level 15 account and password - everything like after password reset.
I tried it again and it again lost settings. So I found following instruction:
http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note09186a00800a65a5.shtml
I followed it and changed again all settings on the router. My settings are again lost after power off/on. I noticed that when I do first bit it does show
0x2102 not 0x2142 like they think that is password reset mode.
Here is my output from Hyper Terminal:
=============================
Cisco#enableCisco#show startUsing 3359 out of 131072 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname Cisco!boot-start-markerboot-end-marker!logging buffered 51200 warningsenable secret 5 $1$hpKF$Rc1tl6r45J8iHG7EN5jSk.!no aaa new-model!crypto pki trustpoint TP-self-signed-3185909327 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3185909327 revocation-check none rsakeypair TP-self-signed-3185909327!!crypto pki certificate chain TP-self-signed-3185909327 certificate self-signed 01 nvram:IOS-Self-Sig#5.cerdot11 syslogno ip dhcp use vrf connectedip dhcp excluded-address 10.10.10.1!ip dhcp pool ccp-pool import all network 10.10.10.0 255.255.255.248 default-router 10.10.10.1 lease 0 2!!ip cefno ip domain lookupip domain name molinary.com!!!username admin privilege 15 secret 5 $1$jD3j$r6ROikgGsIlcMTGjkxFQ6.username username privilege 15 password 0 password!!archive log config hidekeys!!!!!interface ATM0 no ip address shutdown no atm ilmi-keepalive dsl operating-mode auto!interface ATM0.1 point-to-point description $ES_WAN$ ip nat outside ip virtual-reassembly pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 !!interface FastEthernet0!interface FastEthernet1!interface FastEthernet2!interface FastEthernet3!interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$$ES_LAN$ ip address 10.10.10.1 255.255.255.248 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452!interface Dialer0 ip address dhcp encapsulation ppp dialer pool 1 dialer-group 1 no cdp enable ppp authentication chap pap callin ppp chap hostname [email protected] ppp chap password 0 netgear01 ppp pap sent-username [email protected] password 0 netgear01!ip forward-protocol nd!ip http serverip http access-class 23ip http authentication localip http secure-serverip http timeout-policy idle 60 life 86400 requests 10000ip nat inside source list 1 interface ATM0.1 overload!access-list 1 remark INSIDE_IF=Vlan1access-list 1 remark CCP_ACL Category=2access-list 1 permit 10.10.10.0 0.0.0.7dialer-list 1 protocol ip permitno cdp run!control-plane!banner exec ^C% Password expiration warning.-----------------------------------------------------------------------Cisco Configuration Professional (Cisco CP) is installed on this deviceand it provides the default username "cisco" for one-time use. If you havealready used the username "cisco" to login to the router and your IOS imagesupports the "one-time" user option, then this username has already expired.You will not be able to login to the router with this username after you exitthis session.It is strongly suggested that you create a new username with a privilege levelof 15 using the following command.username <myuser> privilege 15 secret 0 <mypassword>Replace <myuser> and <mypassword> with the username and password youwant to use.-----------------------------------------------------------------------^Cbanner login ^CAuthorized access only! Disconnect IMMEDIATELY if you are not an authorized user!^C!line con 0 login local no modem enableline aux 0line vty 0 4 privilege level 15 login local transport input telnet ssh!scheduler max-task-time 5000endCisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#Cisco#show versionCisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARECisco uptime is 20 minutesSystem returned to ROM by power-onSystem image file is "flash:c850-advsecurityk9-mz.124-15.T12.bin"This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)Configuration register is 0x2102Cisco#Cisco#Cisco#Cisco#endTranslating "end"% Unknown command or computer name, or unable to find computer addressCisco#reloadProceed with reload? [confirm]*Mar 1 01:19:27.786: %SYS-5-RELOAD: Reload requested by username on console. Reload Reason: Reload Command.System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARETechnical Support: http://www.cisco.com/techsupportCopyright (c) 2006 by cisco Systems, Inc.C850 series (Board ID: 2-149) platform with 65536 Kbytes of main memoryBooting flash:/c850-advsecurityk9-mz.124-15.T12.binSelf decompressing the image : ############################################## [OK] Restricted Rights LegendUse, duplication, or disclosure by the Government issubject to restrictions as set forth in subparagraph(c) of the Commercial Computer Software - RestrictedRights clause at FAR sec. 52.227-19 and subparagraph(c) (1) (ii) of the Rights in Technical Data and ComputerSoftware clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_teamImage text-base: 0x8002007C, data-base: 0x814E7240This product contains cryptographic features and is subject to UnitedStates and local country laws governing import, export, transfer anduse. Delivery of Cisco cryptographic products does not implythird-party authority to import, export, distribute or use encryption.Importers, exporters, distributors and users are responsible forcompliance with U.S. and local country laws. By using this product youagree to comply with applicable laws and regulations. If you are unableto comply with U.S. and local laws, return this product immediately.A summary of U.S. laws governing Cisco cryptographic products may be found at:http://www.cisco.com/wwl/export/crypto/tool/stqrg.htmlIf you require further assistance please contact us by sending email [email protected] 857 (MPC8272) processor (revision 0x400) with 59392K/6144K bytes of memory.Processor board ID FCZ140792J5MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x104 FastEthernet interfaces1 ATM interface128K bytes of non-volatile configuration memory.20480K bytes of processor board System flash (Intel Strataflash)no ip dhcp use vrf connected ^% Invalid input detected at '^' marker.SETUP: new interface NVI0 placed in "shutdown" statePress RETURN to get started!*Mar 1 00:00:03.952: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Initialized*Mar 1 00:00:03.960: %VPN_HW-6-INFO_LOC: Crypto engine: onboard 0 State changed to: Enabled*Mar 1 00:00:07.244: %LINK-3-UPDOWN: Interface FastEthernet0, changed state toup*Mar 1 00:00:08.413: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to up*Mar 1 00:00:08.821: %SYS-5-CONFIG_I: Configured from memory by console*Mar 1 01:19:27.072: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to up*Mar 1 01:19:27.352: %SYS-5-RESTART: System restarted --Cisco IOS Software, C850 Software (C850-ADVSECURITYK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2010 by Cisco Systems, Inc.Compiled Fri 22-Jan-10 14:46 by prod_rel_team*Mar 1 01:19:27.352: %SNMP-5-COLDSTART: SNMP agent on host Cisco is undergoinga cold start*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.436: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF*Mar 1 01:19:27.540: %LINEPROTO-5-UPDOWN: Line protocol on Interface NVI0, changed state to down*Mar 1 01:19:28.072: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to up*Mar 1 01:19:28.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up*Mar 1 01:19:28.484: %LINK-5-CHANGED: Interface ATM0, changed state to administratively down*Mar 1 01:19:28.848: %LINK-5-CHANGED: Interface NVI0, changed state to administratively down*Mar 1 01:19:28.932: %LINK-3-UPDOWN: Interface FastEthernet3, changed state toup*Mar 1 01:19:28.936: %LINK-3-UPDOWN: Interface FastEthernet2, changed state toup*Mar 1 01:19:28.940: %LINK-3-UPDOWN: Interface FastEthernet1, changed state toup*Mar 1 01:19:29.484: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0, changed state to down*Mar 1 01:19:29.932: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet3, changed state to down*Mar 1 01:19:29.936: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2, changed state to down*Mar 1 01:19:29.940: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1, changed state to down*Mar 1 01:19:29.948: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0, changed state to upAuthorized access only!===========================================
Please help me as I am stuck and can't go any further....

Hi David White,
Alternatively, after password recovery you can modify the configuration to be what you want, and then issue:
write memory
to save the configuration. You can then verify that your changes have been saved to the startup config by issuing:
show startup-config"
The only good thing is that when I switch off a router it erase configuration except my new password which I created after password reset. Everything else is getting vanished (ADSL settings, DHCP, routing ) everything. Even new admin accounts I created.
Well have a question to your above comments. I am new in Cisco so please put as much detail as you can for me to understand. When you say modify configuration do you mean to go to Cisco CP Express graphical interface and then connect router to hyper terminal and execute above commands?
Why router doesn't remember this anyway. There must be some option to change in configuration to make thing permanent when I hit apply changes in Cisco CO Express otherwise it is pointless to heve it.
Phillip
write memory
is
copy running-config startup-config"
Can't this be done via Cisco CP Express or set up router to copy this every time I change this in graphical interface rather going to command line to achnoledge it?
I understand your concern about this router and somebodie's configuration details as you want things to be un-used when you buy them - true. ADSL details belongs to the shop which sold me the router so that is why I don't make a big problem about this. We take most of hardware from this shop and have discount and many good deals with them so I think they have been just testing it and forgot to erease their config. It might be that someone has returned router to the shop and they have repaired it and tested it.
I hope this is a normal behaviour of this router as I have option to replace it in case this is a fault.
Could you please write me step by step guide how can I make changed options stay permanently on router?
thank you
Dragan

Similar Messages

HT201263 I tried to reset my iPhone (3gs) with deleting all data. When it power off and automatically again on then it is showing Apple logo only. Not restore and startup my phone. I tried to charge and not charging. What I should do now?

I tried to reset my iPhone (3gs) with deleting all data. When it power off and automatically again on then it is showing Apple logo only. Not restore and startup my phone. iPhone alerming low charge and I tried to charge and not charging.
What I should do now?

Something has gone wrong. Turn your phone off, then force it into recovery mode:
Leave the USB cable connected to your computer, but NOT your phone, iTunes running, press & hold the home button while connecting the USB cable to your dock connector, continue holding the home button until you see “Connect to iTunes” on the screen. You may now release the home button. iTunes should now display that it has detected your phone in recovery mode, if not quit and reopen iTunes. If you still don’t see the recovery message repeat these steps again. iTunes will give you the option to restore from a backup or set up as new. In your case, select "new".

Wifi problem: I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and n

I have a airport wifi the small one with one port for modem. My Problem is airport wifi works fine however when I power off my IMac then power it up later on It does not show a connection I then have to manual do it my self it's a pain and never happened before I have tried resetting the airport unit but still no luck please help.
Thank you
Roy from malden

Hi Roy, this has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7 & 10.8…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.

Mac mini shut down when i power off my samsumg led smart tv

I'm new to mac mini. In fact Mac at all. I use my samsumg led smart tv as display using hdmi port # 4 in my tv. I have also other devices connect to my tv like my apple tv in hdmi also. I don't know why but when i power off my tv, my mac mini stop to work (like a shut down) and when i power on again my tv i must press the power button on my mac mini in order to use it again, it is no longer list in my listed sources on my tv. My apple tv don't have the same behavior, when my tv is back, I just have to select it again in my source list and it will be back there. Is there something I should change or know in order to have my mac mini always available. I'd like to be able to connect to it from other places using vnc, but right now it's always shutting down and even if I try to power on it after my tv close, it wont when my tv is power off. Somebody can help me? Thank you!

Hi Linda,
Unplugging it from AC power will drain the PRAM Battery in short order, thereby losing setting, like Monitor resolution.
You can test the Pram Battery by disconnecting from the Internet so Date/Time doesn't update before you see it, shutdown, unplug AC for a bit, startup & check Time.
In Sys Pefs>Displays, can you set the resolution?

I'm having problems with my email account. I receive emails when I'm in a wifi zone. But if the wifi is turned off and i'm not in a zone I don't receive my emails through the cellular network. Only when I power off the phone and turn it back on, do I re

I'm having problems with my email account. I receive emails when I'm in a wifi zone. But if the wifi is turned off and i'm not in a zone I don't receive my emails through the cellular network. Only when I power off the phone and turn it back on, do I receive the emails through the cellualr network (again with the wifi off)

In your email settings on the phone check to make sure it is set to receive emails on cellular network. It's a feature you can turn off so your phone isn't constantly updating emails on the cell network, but if you are usually in a place with wifi and aren't concerned about going over your data allowance, you can turn it back on.

I lost the configuration when the power supply is shut down

Hello, i have a problem with a linksys wireless model wrt54gs. When the power suply is off all the configuration is lost. How i can fix that problem?.

I'm having exactly the same problem with a WAP54G that purchased 2 days ago:
I set and used fine within 2 mins of opening shrink wrap. The next day we have a powercut. After power was restored the AP was broadcasting using its factory SSID and default WPA security setting. The Setup Wizard status showed the settings that I had entered BUT admin password was not recognised, neither was "admin" so I couldn't change settings.
I Googled for reset to factory defaults - 60sec press of reset with power on, 15sec power off. Setup wizard confirmed that factory defaults have been restored.
I then used the Web interface to configure - changed SSID, wireless security setting and admin password. Everything ok again.
This morning find that SSID and wireless security settings are set back to default but strangely NOT the admin password. There are no other signs in the house of a power outage, the AP has just lost some of its config.
What is going on?

Loose fullscreen when LCD switched off

I wonder if I can get some help with a problem I have please.
I have a Mac Mini, running two 32" LCD displays mirroring the desktop (one main, one secondary, both showing the same desktop), (utilising the two videos outputs that only Mac Minis have, converted to HDMI with adaptors and audio out cabled separately), running a fullscreen movie presentation. Recently upgraded from a Keynote presentation to a quicktime movie (someone thought sound and movies would be more interesting, and Keynote could not handle the movie clip lengths). When it was on Keynote we could switch off the LCDs at night, leave the Mac Mini running, and then switch on again in the morning and the presentation would be still in fullscreen. In quicktime (v 10.0 OS 10.6), if the LCDs are switched off, then on, they loose fullscreen and have to be put back in cmd+F & cmd+L and then the mouse moved to loose the menu bar. I was wondering if there is a fix for this, that would keep quicktime in fullscreen after the LCDs were switched off, either an automator or console script, or some setting I am missing, would quicktime pro help? Any ideas, I am new to movies and quicktime, but not the mac.

Solve the Issue,
Shut down the Mac
Remove the Power Cabale (wait for 10 seconds)
Connect the Power Cable and Switch on the Mac using the power button and Press CMD+ALT+P+R together.
Dont leave untill you see a qyuck restart

Phone Disconnect when Gateway power off or Restart

Hi,
i have router 1811 , I make it for ISP and VPN connection and routing , beside them i have router 2811 i use it only for CME ,
when i make restart to router 1811 , all phone connected to CME is restart too , i dont know way.
i config DHCP via 1811 and i config ip default gateway (router 1811 IP) on CME .
i add router (local ip phone ip and subnet) to CME , but no luck.
any help about it .
Best Regards
Marwan

The troubleshooting path is restart/reset/restore...if that doesn't work, then a trip to the Apple Store/Genius bar would be advised. We can't speak for the Apple Store, but they have very good customer service.
Reset/restart
http://support.apple.com/kb/HT1430
Restore
http://support.apple.com/kb/HT1414

6700: automatic power-off in car

Hello everybody.
I just got a nokia 6700 classic and installed it in a new mercedes E-class cradle (original mercedes handsfree kit).
My problem is, that the phone does not switch off automatically after e.g. 10 minutes after the ignition is turned off (power off in cardle). Instead the phone is running till the power of integrated battery is down.
Is there a chance to configure an automatic power off when no external power is connected (ignition off) ?
Thanx a lot,
Marc

Not sure, but normally the phone will not turn off when (or after some time delay..) the ignition is turned off... In fact the Cradle (car kit..) turns off when the ignition is turned off or automatically turns off after some time delay when the phone is removed from it...
--------------------------------------------------------------------------------------------------------------------------------------------------------If you find this helpful, pl. hit the White Star in Green Box...

Documents uploaded to icloud disappear when I turn off the IPAD

documents uploaded to icloud disappear when I turn off the IPAD,I can see the documents only when icloud is open on the PC

When you turn off any device, it will disconnect from the internet. My sense is that you're not quite explaining what's happening. Do you mean that when you turn it back on again it doesn't automatically reconnect? Do you mean the if it just goes to sleep (as opposed to being powered off) that it switches from WiFi to cellular? Or are you saying that you think that when you turn off the iPad, the router disconnects?
If you're trying to say that the iPad disconnects from WiFi when asleep and switches to cellular, the solution is to keep it plugged into a power source.
Best of luck.

Help! Power-off Recovery

Brand new to iMac and I screwed up already.
I put my iMac to sleep with a number of items still open, specifically a Numbers doc and my iTunes. I then unplugged my iMac to move it (without shutting down) and then it froze when I turned it back on and tried to play music with my remote. I then powered off by pressing the off button. Everything seems to be working fine EXCEPT that my personal library is not showing in iTunes and I can't open the Numbers doc that had been open when I power off (although the saved doc is showing up in Finder).
Can anyone help with suggestions on how to recover? It's not the end of the world although I would like to save a few hours work on the Numbers doc?
Thanks in advance -- I am definitely a Mac convert -- just need some help reprogramming my PC brain from ctrl-alt-del.

Thanks for the quick reply -- did as you suggested but no luck. I restarted thereafter but still no luck. The iTunes issue is not that big a deal -- I can just re-sync from my iPod.
But I really would like to recover the Numbers doc -- it's showing up in my saved docs but when I try to open I get the error message that ir can't be opened. Any other suggestions?

Satellite P300 156 PSPC4E - White Media LEDs stay on after power-off

HI
I have a Toshiba Notebook Satellite P Series P300 156 (PSPC4E) which has just developed a problem
When I power off, the laptop shuts down normally and power button itself goes off, but the 6 white media LED's to the right of the power button remain on constantly. The only way to get these to turn themselves off is to disconnect the battery.
Can anyone please advise
Many thanks

Thanks for the replies
I tried altering the BOIS, but that only affects the illuminated strip along the top of the mouse touch pad.
I cant remember which version of BIOS that I got (I'm at work at the moment) but I tried downloading the latest from here (dated 18/03/10), and it made no difference.
Its a strange one. The lights stay on even if the laptop is closed for long periods. They just never go off, unless I take the battery out.
Message was edited by: hawkerpaul

Xorg black screen after monitor power off, AMD r9 270X & aoc u2868pqu

Is there a way to get xorg to reset its video settings, and how are we getting more debug messages out of xorg these days?
(not any kind of emergency as everything is "working")
when I power off my monitor for a few minutes xorg goes completely black.
I can switch to other TTYs and start a second xorg from there
When I try to get back to the original TTY that xorg's still black.
these messages show up on the second TTY
<code>[34181.758006] [drm:si_dpm_set_power_state [radeon]] *ERROR* si_restrict_performance_levels_before_switch failed
[34181.835519] [drm:radeon_dp_link_train [radeon]] *ERROR* displayport link status failed
[34181.835526] [drm:radeon_dp_link_train [radeon]] *ERROR* clock recovery failed
[34181.838937] [drm:radeon_dp_link_train [radeon]] *ERROR* displayport link status failed
[34181.838942] [drm:radeon_dp_link_train [radeon]] *ERROR* clock recovery failed</code>
nothing looks relevant in
~/.local/share/xorg/*
these messages also show up if I turn off the monitor when positioned on a console, but the console is still accessible on monitor power up.
none of these show up if I turn off the monitor when positioned on a KMScon, and the KMScon is still accessible on monitor power up.

Is there a way to get xorg to reset its video settings, and how are we getting more debug messages out of xorg these days?
(not any kind of emergency as everything is "working")
when I power off my monitor for a few minutes xorg goes completely black.
I can switch to other TTYs and start a second xorg from there
When I try to get back to the original TTY that xorg's still black.
these messages show up on the second TTY
<code>[34181.758006] [drm:si_dpm_set_power_state [radeon]] *ERROR* si_restrict_performance_levels_before_switch failed
[34181.835519] [drm:radeon_dp_link_train [radeon]] *ERROR* displayport link status failed
[34181.835526] [drm:radeon_dp_link_train [radeon]] *ERROR* clock recovery failed
[34181.838937] [drm:radeon_dp_link_train [radeon]] *ERROR* displayport link status failed
[34181.838942] [drm:radeon_dp_link_train [radeon]] *ERROR* clock recovery failed</code>
nothing looks relevant in
~/.local/share/xorg/*
these messages also show up if I turn off the monitor when positioned on a console, but the console is still accessible on monitor power up.
none of these show up if I turn off the monitor when positioned on a KMScon, and the KMScon is still accessible on monitor power up.

Recomended External HD FW800 with power-off/sleep feature

Hi.
After "googling" some hours, I dont want to miss asking here before I spend more money, beacuse i could skip any model or so... Any recomendations (based on knowlage or experience) of brand/model to buy for an external HD with this kind of features:
- FireWire 800 port (does 800 give 400 compatibility?)
- supports 1Tb or some more
- power´s/off/on when I power-off/on my iMac, or if it sleeps.
-last, not so important but cool, could include some USB/firewire Hub feature too.
thanx
vcosta

I have to agree with the previous poster, the LaCie Quadra D2 are good drives. I have 3 (320, 500 & 750 GB) daisy chained together connected via FireWire 800 so far they are running fine. However others really like OWC Mercury series too. You can find those at:
http://eshop.macsales.com/shop/firewire/1394/USB/EliteAL/

BB Q10 - Difference between Power OFF and "Battery pull out"?

Hello,
Any one has any info on what difference the phone sees between a proper power switching OFF and doing a battery pull out?
Apparently, some of the customer service guys at BlackBerry advises you to do a battery pull out while the phone is in ON mode.
Just curious to know what is the reason behind it.
Solved!
Go to Solution.

When you power off your phone, it keeps everything intact until you power on again. When you do a battery pull, it interrupts the operation of the phone and many temporary files, not necessary to the proper operation of the phone, are erased. In many instances, when there's something playing havoc on your phone it can be found within these temp files.
Another method to do a battery pull is to press and hold the power button until BlackBerry appears on the screen. Other things will appear before that but if you continue holding until it shows, the effect is similar to doing a battery pull with the phone powered on. Note that pressing the power button to shut off the phone does not erase these temp files unless you hold it until BlackBerry shows, usually about 15 seconds.
I hope that helps you.
- If my response has helped you, please click "Options" beside my post and mark it as solved. Clicking the "thumbs up" icon near the bottom of my response would also be appreciated.

I am loosing configuration when I power off my Cisco 857 router

Similar Messages

Maybe you are looking for