I am not able to remove crypto map SONZOGNI^@

Please,show me the command to remove crypto map SONZOGNI^@ .
Command "no crypto map SONZOGNI^@" doesn't work,the response is crypto map unexisting.
The Router model is 3640.
Thanks
12.0
service timestamps debug datetime localtime show-timezone
service timestamps log datetime localtime show-timezone
service password-encryption
boot system flash:c3640-is40-mz.120-24.bin
logging buffered 32000 debugging
no logging console
ip subnet-zero
no ip source-route
no ip finger
no ip domain-lookup
isdn switch-type primary-net5
crypto map SONZOGNI^@ 1
set peer cisco-sonzogni
match address sonzogni-encrypt
clock timezone CET 1
clock summer-time CET-SUM recurring last Sun Mar 3:00 last Sun Oct 3:00
call-history-mib max-size 200

Try no crypto map SONZOGNI^@" 1, you have to mention the 1 also.

Similar Messages

  • ** Not able to create Value Mapping Table in Integration Directory

    Hi friends,
        I am not able to create value mapping entries like below in ID.
    Agency :    Computer1                Agency : Computer2
    Scheme:    Country                     Scheme: CountryCode
    Value for Computer1                   Value for Computer2
    Australia                                     AU
    India                                           IN
    Austria                                       AU
    Note that I have assigned the same country code 'AU' for the Countries 'Australia' & 'Austria'. But, when we assign 'AU' to 'Austria', the system asks question as below:
    Value mapping already exists
              Australia | AU
              Austria | AU
    Do you want to delete it from the existing group and assign it to the current group instead?
                       Continue       Cancel
    Though choose any of the option, I am not able to assign 'AU' to 'Austria'.
    Friends, this is my requirement. How do we solve this ?
    Kindly help me.
    Kind Regards,
    Jeg P.

    Hi Koen,
        I tried this. Its working fine now. Thanks for giving guidance to me. Then, I have another doubt. Suppose if we create 2 sets of VM table, (First Receiver will act as 2nd one how do we achieve this). For Ex:
    Set 1:
           Source Agency: SYS1              Target Agency: SYS2
           Source Scheme: CODE             Scheme : DEPT
             A                                            HR
             B                                            Accts
             C                                            Finance
    Set 2:
           Source Agency: SYS2              Target Agency: SYS3
           Source Scheme: DEPT             Scheme : GRADE
             HR                                             Second
             Accts                                          First
             Finance                                       First
    In this case, I followed the same logic which you said, but I am not able to create. I think the main point is GUID here. If you have any idea, kindly tell me.
    Kind Regards,
    Jegathees

  • Not able to find the mapping for table W_CUSTOMER_STATUS_HIST_F_TMP

    Hi All,
    I have implemented the Out of Box solution of Order Management Analytics module with 11.5.10 version of Oracle EBS and respective adopters. Under the same I am not able to notice any mapping to load the data into W_CUSTOMER_STATUS_HIST_F_TMP table and due to which it causing few reports under order management.
    Could you please tell me the mappings name for this Target Table so that I can verify from my side if it has been missed or so?
    I am finding this W_CUSTOMER_STATUS_HIST_F_TMP table is getting used as Source Table under the folder of PLP for the mapping as,
    PLP_CustomerStatusHistoryFact_Extract
    PLP_CustomerStatusHistoryFact_Old_Customers_Load
    and PLP_CustomerStatusHistoryFact_Extract
    Thanks,
    -Vinay

    Not sure this would help but As per data lineage guide, it says PLP_CustomerStatusHistoryFact_Extract mapping populates this table from series of different tables. Later, From temp table it goes to W_CUSTOMER_STATUS_HIST_F table via mapping PLP_CustomerStatusHistoryFact_New_Customers_Load
    ~r

  • Not able to remove 'emtpy home' directory entry

    Hi
    I'm trying to remove an Oracle 10.2.0.1.0 installation on a Linux system. My problem is, that I'm not able to remove an 'empty home' directory with the installer. The button 'Remove..' is grayed out.
    The reason why I want to remove that directory is, that I want to do an installation into this directory again. But the requirements check of the installation fails because of this 'empty home' directory (which is actually deleted on the file system).
    Does someone know where this information is stored on the filesystem or how I can force the installer to install in this directory anyway? BTW: I have also a 9.2 installation on the same system, but that's probably no problem.
    Thanks!

    Has this database been upgraded via the patch process? If so, run the installer from the patch directory, you can often get to the uninstall from there. It all has to do with oracle inventory and what it sees as your most recent install. After you have done the uninstall/remove, you can just go delete the directory and remaining contents -- there will not be much left.

  • I am not able to remove an element of my side bar of the finder

    I am not able to remove an element of my side bar of the finder

    Try holding down the COMMAND key while dragging the element to the desktop.

  • Not able to remove the ABAP code from Transformation

    Hello Experts,
    We have transformation for DSO in that for one infoobject, field routine is written, Break Point is hard coded there and it's move to production. Now we are trying to remove that break point from development and then move it production.
    we are doing following activity to remove the break point.
    1. Open the transformation.
    2. Open the field routine.
    3. Going to ABAP code in field  routine.
    4. Remove the hard coded Break Point from ABAP code.
    5. Saving the code.
    6. It's taking to again filed routine window.
    7. We close the window and activate the transformation.
    8. When again check the ABAP code in field routine then it shows hard coded Break Point again.
    9. Not able to remove the hard coded break point.
    Can anyone know how to do this.
    Help will be appreciated.
    Thanks

    Hi,
    As pointed above, after point 6 don't simply close the window but click on Transfer Value and then activate your transformation. Refresh the system and check again.
    Regards,
    Arminder

  • Not able to remove items from initiative

    Hello All,
    We are on PPM 5.0 and I am trying to remove added items from the 'initiative' but I am not able to remove them.
    Can someone kindly help, as to what might be preventing from removing items from initiatives.
    Thanks,
    Sachin

    Hi,
    If you want to remove the Items from Intiative , you need remove the relationships object . Not possible to delete directly !
    Steps :
    Navigate to the Relationships tab , then go to the Sub tab Related Objects , select the Item  and click Delete Assignment. You will remove the Item from Initiative dashboard !
    Hope it works for you !
    Regards,
    Vincent
    Edited by: ddd002 on Oct 4, 2011 6:53 AM

  • Not able to remove User from supervisor desktop

    Im not able to remove an user that is not longer with the company from the queue, its on the agent queue and its shows at log out.
    I already remove the user form CUCM, also deleted from the inactive user at the ccx admin, also Synchronize Directory Services and nothing..
    the only thing I would like to do is
    restart the Cisco Desktop Sync Service. but I dont know if I can do that during production without affecting other agents.
    UCCX
    Cisco Unified CCX Administration
    System version: 8.5.1.11003-32
    thanks

    Hi Alberto,
    Do you see this User ID in the Team which is managed by this supervisor, please de-associate it from the Team incase if it still appearing in the Team's associated list.
    Hope this helps.
    Anand
    Please rate helpful posts !!

  • I have "@mail.ru" tool bar(i think) under the address bar. Its in a different language. I am not able to remove that. Please help me to remove that

    I have "@mail.ru" tool bar(i think) under the address bar. Its in a different language. I am not able to remove that. Please help me to remove that. Its not listed under 'Extensions', plug-ins,add-on too..
    Thanks

    Please look at another post I have just made relating to mail.ru, and post back with how you get on.
    * [/questions/924267#answer-323108] <-- clickable link -- (blue) --

  • Not able to remove a attendee assigned on business event

    Hi,
    I am not able to remove a attendee assigned on business event
    it shows in tcode psv2. but cant delete it.
    points will be rewarded.
    thanks

    Hi Vinayak,
    I have been tryng to cancel the attendee booking but it is not allowing me to cancel. When i press the cancel button it does not do anything. nor it show any error message. i am unable to understand the reason.
    plz help
    regards
    TS

  • Not able to do user Mapping with the backend System

    Hello all,
    I am trying to Map a user to a windows based KM System but getting an error like
    "There is a configuration issue which leads to problems when accessing user mapping data for the selected backend system 'KM_Test_System'. Usually, the reason is user mapping being configured for strong encryption, but the necessary additional files being missing. Check the security log file for further information and hints on how to solve the problem."
    Can somebody tell me what could be the possible reason for this and how to handle this. I dont have access to the Portal server right now , so not able to see the security log.
    Thanks to all,
    Regards,
    Sarabjeet Singh.

    Hi Sarbjeet,
    I believe this links will help you understand and solve your problem:
    user mapping is not saved
    and
    http://help.sap.com/saphelp_nw04/helpdata/en/04/d246215f1d4f588d1d9c49391acb01/frameset.htm
    Hope this helps,
    Robert

  • Map viewer is not able to parse WMS map request

    I am experimenting with using Mapviewer to deliver WMS data using the built-in WMS support as documented in appendix D of the manual. The Mapviewer version is 10.1.2.0.2.
    Using the following arguments in a browser window, I am able to receive a map image from Mapviewer (I have defined the datasource 'namn_utv' and the map 'SN8307'):
    VERSION=1.1.1&
    SERVICE=WMS&
    REQUEST=GetMap&
    STYLES=&
    FORMAT=image%2fpng&
    SRS=EPSG:4326&
    BASEMAP=SN8307&
    LAYERS=&
    BBOX=5,60,6,61&
    WIDTH=524&
    HEIGHT=524&
    BGCOLOR=0xFFFFFF&
    EXCEPTIONS=application/vnd.ogc.se_xml&
    DATASOURCE=namn_utv
    The problem is that applications able to render WMS layers do not send exactly this format (I have tried ESRIs ArcGIS version 9.1 and Cadcorp SIS Map Browser version 6.2.658). They do not specify the BASEMAP parameter or the DATASOURCE parameter, as they are Mapviewer only.
    Is there a way to make Mapviewer accept standard WMS requests such as the one below? Or do I have to re-implement the WMS support myself to be able to handle such requests?
    VERSION=1.1.1&
    SERVICE=WMS&
    REQUEST=GetMap&
    STYLES=&
    FORMAT=image%2fpng&
    SRS=EPSG:4326&
    LAYERS=NAMN8307&
    BBOX=5,60,6,61&
    WIDTH=524&
    HEIGHT=524&
    BGCOLOR=0xFFFFFF&
    EXCEPTIONS=application/vnd.ogc.se_xml
    Kind regards,
    Øyvind Eide

    Rename your datasource to WMS.
    Then omit the datasource and basemap names from the request.
    See Sec D.2.1
    The default data source for a GetMap request is WMS. That is, if you do not specify the DATASOURCE parameter in a GetMap request, it is assumed that a data source named WMS was previously created using the <add_data_source> element (described in Section 7.1.1) in an OracleAS MapViewer administrative request.
    "

  • Not able to select Operation Mapping in Directory

    Hi,
    I am doing a SOAP to SOAP scenario. Both the inbound and outbound interfaces have 2 operations each. I am facing a strange problem -
    1. in the interface determination, I am able to select the inbound interface for both the operations of the sende interface (value is the inbound interface). But when I  wanted to selct the operation mapping, it shows the defined OMs from the repository but when I select them, it does not show up in the box. I tried using both java 1.6 and 1.5 JDKs.
    2. Since we can have only one sender agreement (though the sender interface has 2 operations), with one communication channel (SOAP sender), how to direct it to the receiver side operations? I am not able to create 2 receiver agreements as it is compalining that it is a duplicate object. If I can not do this, I would not be able to specify the soap action in the receiver channel which actually routs it to the right operation on the receiver side.
    Any ideas?
    Thanks,
    Sri

    Hi,
    >>Since we can have only one sender agreement (though the sender interface has 2 operations), with one communication channel (SOAP sender), how to direct it to the receiver side operations? I am not able to create 2 receiver agreements as it is compalining that it is a duplicate object. If I can not do this, I would not be able to specify the soap action in the receiver channel which actually routs it to the right operation on the receiver side.
    You need to use dynamic configuration, check my rely on this thread
    Re: Consuming web services provided 3rd
    Regards
    Suraj

  • Not able to remove the BizTalk Application from Admin Console

    While removing the application I am getting the below error and after that not able to see any Resources also for the same application.
    TITLE: BizTalk Server 2009 Administration Console
    Delete of ApplicationNode failed.
    ADDITIONAL INFORMATION:
    Error while removing application XXXXXX". (mscorlib)
    For help, click: http://go.microsoft.com/fwlink/?LinkId=47400&ProdName=Microsoft+BizTalk+Server+2009&ProdVer=3.8.368.0&EvtSrc=Microsoft.BizTalk.ApplicationDeployment&EvtID=RemoveApplicationFailure
    Method not found: 'Microsoft.BizTalk.ExplorerOM.BtsCatalogExplorer Microsoft.BizTalk.ExplorerOM.BtsCatalogExplorer.GetBtsCatalogExplorerInstance()'. (mscorlib)

    Hi,
    the problem here is that your installation is effectively corrupt, in other words the combination of assemblies on the system does not match one of the supported configurations. I hope this is not a production system?
    Having said that I think you have taken some repair steps?
    The specific error here is that the administration console is not getting matched with the correct version of the dependent assembly. So your first step is find a working BizTalk dev system and determine what the correct versions are. The best way to do
    this is to take advantage of the tools associated with the .net Fusion system. See here for a good description:
    http://blogs.msdn.com/b/suzcook/archive/2003/05/29/57120.aspx. Also that post is a little old, if you have a .net 4 based system the locations need to be tweaked (but you don't in BTS
    2009).
    What it will allow you to do is obtain a trace of  where .net looked for assemblies  and where it found the one it used. 
    It should be trying to find: microsoft.biztalk.explorerom.dll.  However it takes a bit of time to understand the logs so just because you see a few failures don't worry, you are interested in the one it found.
    mark

  • Cisco 5520: removed crypto map still in effect

    so i typoed a command: "crypto map Map1 7"... instead of "crypto map Map1 70".
    I cleared the Map1 7 entries, and added the correct entries in Map1 70.
    I cleared all of the vpn sessions:
    no crypto map Map1 int outside
    cl ips sa
    cl isa sa
    Now, however, whenever I try to ping the remote network from the inside interface, it seems to read the Map1 7 policy instead of Map1-70.
    Is there anyway to clear the Map1 7 entries from memory? I'm trying to avoid rebooting the firewall.
    Thanks,
    Jeff
    But when I try

    With ASA you need the "clear configure" command to remove a crypto map sequence number
    clear configure crypto map map-name seq-num
    (in configuration mode)

Maybe you are looking for