I am trying to hook up a second airport extreme to extend my network. Can I do this without having another ethernet connection?

I am trying to hook up a second airport extreme to extend my wireless network. Can I do this without having a second ethernet connection?

Yes. Apple's instructions to do this are here:
http://support.apple.com/kb/HT4259

Similar Messages

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

I am trying to install a second airport express to extend my network. When I use the aiport utility it does not see the second airport express.

Suggest that you perform a Factory Default Reset as follows:
Pull the Express from power
Wait a few moments
Hold in the reset button and keep holding it an additonal 8-10 seconds while you plug the Express back in to power
Release the reset button and allow 40-45 seconds for the Express to restart
Apple's instructions to do what you want are here:
It will often help to temporarily connect an Ethernet cable from your Mac to the AirPort Express for the setup. Once the Express is configured, you can disconnect the Ethernet cable and move the Express to the desired location.
http://support.apple.com/kb/HT4259
Although an AirPort Extreme is shown as the extending device in the example, the setup for an AirPort Express is exactly the same

When I try to quit firefox, it hangs. I cannot force quit and I cannot restart. I tried the online help which directed me to uninstall, but I couldn't find library /application support. How can I fix this without having to turn off the computer?.

I cannot force quit and I cannot restart. I tried the online help which directed me to uninstall, but I couldn't find library /application support. How can I fix this without having to turn off the computer?.

Not sure if this Term is Relevant towards an iPhone but, my iPhone won't Post unless if it's plugged into a Charger.

HT4628 Using an Airport Express and a second Airport Extreme to extend network; will proximity to AEX vs. AE make a real world difference in speed

I have set up an extended network (thanks go to Bob Timmons for his assistance) using an AE as a base station and a second AE and an Airport Express to extend the wireless signal. Comcast provides, so they say, 50 Mbps. The AEX is located in the bedroom where it is used more often and the AE is in the pantry (for occasional use in the garage.) Would I get better speed/signal strength if I switched the two devices; i. e., placed the Airport Extreme in the bedroom and the AEX in the pantry?

Thanks for your response. I set up the wireless network because running Cat-5 was cost prohibitive. My internet connection is very good for general purposes but I ask the question, somewhat academically, because Wi-Fi Explorer shows the Max Rate of the network devices as follows:
Airport Express (located in the bedroom): 144 Mbps @ 2.4 GHz
Airport Extreme (in the pantry): 217 [email protected] GHz
To reiterate, If these two changed locations would I get better speed/signal in the bedroom location? Does it even really matter since Comcast is "only" sending me 50 Mbps? Just a couple of questions to keep my mind active (and confused).

How do I install a new airport express and link a second airport express to extend the network of the first airport express?

I currently have a linksys wireless router attached to the Internet. I have an A1264 Airport Express connected by Ethernet to the linksys router. I have two network names, one for each wireless network.
I purchased a new A1392 Airport Express to replace the linksys router and join to the A1264 Airport Express, and I want to have one network name as a result.
How do I do this? I realize that I have to reconfigure the A1264 device so that it is an extension of the A1392 device.

You have a fairly complicated set up, so I suggest that it would make sense to tackle things in stages, testing each stage as you go, before proceding to the next stage.
Stage 1 would be setting up the A1392 first to the cable modem, and then making sure that everything is working correctly on the A1392 Express
Stage 2 would be adding the Netgear switch and testing each port with a laptop connected via Ethernet to make sure that everything is operational on the switch
Stage 3 would be connecting the A1264 Express and testing to make sure that it is extending the network correctly
Stage 4 would be adding other Ethernet devices to the Netgear switch and testing each one at a time before adding the next device. There is some question about whether an iOS device can print to an Ethernet connected printer....even if the printer is AirPrint compatible. You may need to connect the HP using wireless...not Ethernet....to gain full AirPrint functionality, or use another application that will allow printing like Printopia or Print Central using the Ethernet connection on the HP.
Stage 5 would be adding the printer to the A1264 AirPort Express.
You do not mention how the printer will connect to the A1264 Express, but I assume that it will be USB from your description. Most printers will work, but you really will not know if your printer will work until you try.
Remember that only printing will be supported at the USB port of the Express. If you have an all-in-one type device, scan, maintenance, and other advanced features will not be operational whent the device is connected to the AirPort Express.
If you want to print from an iOS device like an iPad or iPhone, plan to add additonal software like Printopia or Print Central to possibly allow this function. There are no guarantees here as far as the iOS devices.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. Any tips on how to do this?

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to connect a Windows 7 / 64 bit to an Epson printer on my Mac. The printer is hooked into the Mac via USB; the Mac is networked to a Linksys wireless router with an ethernet cable, as is the Windows box. I installed the current Bonjour printer services software on the Windows machine, and separately installed the driver software for the Epson printer on the WIndows machine. Running the bonjour wizard, I get an alert saying 'I don't have sufficient access to my computer to connect to the selected printer'.
The printer has 'sharing' turned on from the Mac end; this works with a Powerbook via the wireless connection. Sharing is also turned on in the Windows printer control panel for this printer (under properties). The Mac is a G5 running 10.5.8. When I try to print a page from the Windows machine it gets hung in the print queue.
Any advice how to proceed would be appreciated!
thx,

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn't support this base station. Go to AirPort Service and Support for more information."

I am trying to hook up my Airport Express to my current network and AirPort Extreme but keep getting the same error message: "This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Any thoughts?

This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express.

My ipods frozen on the white apple and black background page. I've tried resetting with the hold button, but nothing's changed. How can I fix this!?

My ipods frozen on the white apple and black background page. I've tried resetting with the hold button, but nothing's changed. How can I fix this!?

Try this...
Restarting your device
1) Press and hold the Sleep/Wake button for a few seconds until the red "slide to power off" slider appears, and then slide the slider.
2) Press and hold the Sleep/Wake button until the Apple logo appears.
Follow these steps to reset your device
Note: Reset your device only if it is no longer responding and the steps above do not work.
Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
Restart / Reset
http://support.apple.com/kb/ht1430

Hard drive goes to sleep in 2 minutes when hooked up to my Airport Extreme?

I have a usb hard drive hooked up to my airport extreme as a network drive and it works great, I use it for all my movies and music and all my computers on my network can access the drive, but if I am not accessing a file it goes to sleep really quickly and then when I do want to access a file I haft to wait for the drive to spin up again. As long as a video or music is playing off it it continues to run as you would expect, just wondered if any one knows why it goes to sleep so quickly and is there away to extend the sleep time.
Thanks

I don't know the exact reason but I've tried different externals and internal drive in the TC or usb attached to TC or the Extreme and some drives don't sleep and its annoying that these would use unneccassary power.

Argh! Trying to Replace Linksys with New Airport Extreme...

Been fighting with this for hours...about ready to take the new Airport Extreme back ...Here's the deal:
I currently have a very wired and wireless 2story home professinally set up with 2 Linksys devices as the primary network and a couple previous generation airport expresses as extenders.   Due to video, audio and other systems the primary router for the network/WAN closet out in the garage needs to remain on the primary Linksys (non wifi) router. I want to replace the Linksys Wifi router (see below) that is puposely set up and has worked for several years as a double NAT config with the new Airport Extreme but i have tried duplicatiing the exact configs from the Linksys router and all the various ways you can use the Airport Express in DHCP/NAT and even in Bridge mode and it still wont work! I've never considered Linksys software easier (and definately more flexible and informative) to use than Apple until this experience! Very frustrating.... I'm being very explicit and using the typical Linksys config profiles below so as to hopefully help you translate this into specific configs i can wrangle into the Airport Extreme to make it work like the
Current Primary Network:
Current WAN Router / + 24 Port Switched LAN Network (for wired ethernet access ports used throughout house) > Linksys BEFSX41 + Linksys 24 port Switch locted in a custom built data /video / audio closet in garage
WAN IP: DHCP
LAN IP: 192.168.1.1
Subnet Mask: 255.255.255.0
Current WiFI Network > Linksys WRT160Nv2 (currently conected to the 24port switch via a hardwired ethernet wall port upstairs in my office)
Internet Connection Type: Static IP
WAN IP: 192.168.1.2
Subnet Mask: 255.255.255.0
LAN IP: 192.168.0.1
Subnet Mask: 255.255.255.0
Per config notes from the network engineer who i worked with to build this network when i built the house
"this allows the 192.168.0.x wifi device to successfully route to the 192.168.1.x wired router (and vice versa)"
My goal is to replace the Linksys WRT160Nv2 with the new Airport Extreme (whose range and ability to reach both upsatirs and outside to the beach is MUCH better) and locate it DOWNSTAIRS and connect it in the same way as the Linksys (via an ethernet port in the living room) to the same switch / router in the data closet.
I have tried to set up the new Airport Extreme to replicate this config several different ways both bridged and not bridged (including telling it to ignore the double NAT warning) with the latest.   I am pretty sure non-bridged is the right way to do it but i seem to lack a config parameter to tell the Airport Extreme to replicate the equivalent of the WRT160Nv2 settings despite trating all the submenues and options on the airport extreme set up / Airport Utility App. Do i have to telnet directly into the Airport Extreme config files to do this natively? Help!
PS - no i cannot / will not put the Airport Extreme in to replace the primary Linksys router in the data closet - there is no way it will fit or that its wifi could penetrate the EMI and insulation of all the other electronics in the data closet out in the garage and get a good connection into the house

The trick on the airport extreme is to change the DHCP .. when you change the DHCP it changes the actual IP of the AE..
So go to the setup and open the dhcp, in the network options and you can select by arrow the first two octets and replace the third.
I just posted info on this in another post..
https://discussions.apple.com/thread/5134560?tstart=30
Does this answer your question, as I am a bit unclear otherwise??
I have to say I do not like using double NAT.. it is becoming worse and worse as the amount of material on the internet that requires interactive connection increases.. you block so much by doing this.. double NAT is an issue .. not just ignore the warning.
There is no reason why you need double NAT.. you should have a single flat network. If you need to keep some things isolated from others the correct way to do it is vlan.. but you will need a better router than the old linksys to do it. And possibly a managed switch. Nowadays a managed 24 port gigabit switch is not a bad price at all.

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network?

My home network has an Airport Extreme w/Time Capsule as the base and then an Airport Express and a second Airport Extreme to reach different areas of the house. Is there a way to use the second Airport Extreme for file storage on this network? Network is administered through an iMac running OS X Yosemite 10.10.2. Ideally, would like for the second Airport Extreme hard drive to appear on the list of devices in the Finder window.

Ok.. gottcha
The problem is network wise.. Yosemite is about equal to tin cans and string.. pathetic.
Here is my usual set of instructions to get anything working on Yosemite.
The best way to fix problems is a full factory reset of all the AE in the network.
Factory reset universal
Power off the AE.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the AE to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg AEgen5 and AEwifi for basestation and wireless respectively.
Even better if the issue is more wireless use AE24ghz and AE5ghz with fixed channels as this also seems to help stop the nonsense.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the AE always takes the same IP address.. this is not a problem for AE which is router.. it is a problem for AE which is bridged.. you will need to set static IP in the main router by dhcp reservations or use static IP in the AE which is tricky.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric..
5. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
6. Now mount the disk of the second AE in finder... manually.
Use Go, Connect to Server and type in the AE ip address.
SMB://10.0.1.2
Where you will replace that address with the actual address. The network resource should be discovered and then it will request the password.. type that in and make sure you tick to save it in your keychain.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
Do as much as you want of the above... not all of it is necessary.. only if you want it reliable.. or as reliable as Yosemite in its current incarnation can manage.
The most important thing is point 6.. mount the disk using direct IP address and not names.. dns in Yosemite is fatally flawed.
See http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

After trying to change permissions on my computer so others on my network can access files, my external Hard Drive has a lock on it and I can't access files. I've tried repairing permissions, logging in under another Administrator account, using Terminal

After trying to change permissions on my computer so others on my network can grab files, my external Hard Drive has a lock on it and I can't access files. I've tried repairing permissions, logging in under another Administrator account, using Terminal to fix the problem, downloaded BatChmod but nothing works… Any other suggestions? I have an Imac running OS10.6.8.

There is suddenly a lock icon on my external backup drive!
Custom Permissions

Can I use a second generation Airport Extreme to extend my Time Capsule network?

I have a second generation Airport Extreme (circa 2009?) and am thinking of buying a Time Capsule. Can I use the Extreme to extend my network?

Yes. Note; however, you won't be able to extend the 802.11ac mode of the new Time Capsule. Also be aware that the 2nd generation Extreme did not provide for simultaneous dual-band operation. That would mean that you will only be able to extend either the 2.4 or 5 GHz band, not both at the same time.
... so it can work in a limited fashion.

My macbook crashed and I am trying to install my adobe programs again but I can't because he is used earlier by myself. How can I fix this without buying a whole new packet?

My macbook crashed and I am trying to install my adobe programs again but I can't because he is used earlier by myself. How can I fix this without buying a whole new packet?

Hannahdb1 what specific Adobe applications are you attempting to reinstall? Do you receive any specific error messages? Finally what version of Mac OS are you using?

I am trying to hook up a second airport extreme to extend my network. Can I do this without having another ethernet connection?

Similar Messages

Maybe you are looking for