I am trying to print and only blank pages and codes are printing?

My family have recently got a FujiXerox DocumentCentre C240 and I am trying to print to it. I have downloaded the printer software and added the printer through the IP address with selecting the right printer software. The printer says it is installed corrected and when I go to print it starts printing pages with a codes of what I'm trying to print at the top as well as lots of blank pages after.
What can I do to make this work and print what I want it to print?

Contact FujiXerox

Similar Messages

  • Printing only blank pages and Page setup dialog box is black

    When I go to firefox - Print - Print preview - Page setup OR
    Firefox - Print - page setup
    This dialogue box is black. I can't move or adjust it. Nothing is on that screen.
    When I print a webpage (ctrl P, or Firefox, print) nothing is printing.
    I tried a suggestion of resetting by following the instructions here. That did not work.
    http://kb.mozillazine.org/Problems_printing_web_pages#Reset_printer

    I just experienced this problem, and stumbled upon the cause and the fix. When I went to "File" and then "Print Preview" I was getting a "black" screen where the preview should have been. I tried the suggested fixes related to about:config printer settings and add-on's, etc... but it did not help.
    Then, I looked at the "Page Set-up" when I was on the "Print Preview" page. The bottom margin (for whatever strange reason... have no clue) was set at a huge number of inches... like 43801.4 or some such. I changed it back to 0.3 inches... fixed it. Can print just fine now.
    So... if all else fails: check your margin settings on page set-up.

  • OS X 10.6.7 Canon All-in-One 480 Printer will not print files, only blank pages. Have to go to Utilities, Disk Utility  and Repair permissions for a temporary fix. How can I get a permanent fix?

    After upgrading to OS X 10.6.7., my Canon All-in One MP 480 printer will not print. it says it is printing, but the sheet of paper just runs through the printer and comes out blank. I finally went online to just answers.com and got a fix involving the System preferences, printer and fax. i was told to go to Applications in the HD, thenUtilities, then Disk Utilities, highlight the HD and check on Verify Disk. If it says Disk is OK, click on Repair Permissions. At first, that worked, but the next time I went to print after turning the printer off, it refused to print and just ran the sheet of paper through blank. Once that happens, there is no way to go back to printing the file that failed. I fiinally had to copy and paste the info from the file that would not print and put it in an email to myself and then print that. This is very frustrating, and I would really like a final solution for the problem.
    bettyfroomneedham

    There's a lot there, so I'll start with the parts I can answer quickly.
    The "ACL found but not expected..." messages can be safely ignored, so says this article
    http://docs.info.apple.com/article.html?artnum=306925
    (look below all the "SUID" examples)
    I had changed my Desktop image earlier but when the "Installing 1 item" window came up it changed back to the back ground that you first see on your desktop after installation.
    Leopard installs updates a bit differently. If it's simply an application that does not change system files, it installs them like before, without having to restart. If the update is to the system, then you must immediately "restart," It then goes to that stars and purple screen to perform the installation. Before, it would do the installation while you still had control of the Mac and would prompt you to restart when it finished the installation. This change probably make things more secure and reliable, because you aren't allowed to do other things on the Mac while system updates are being installed.
    Please post back with the remaining point of concern.

  • Photosmart All in one C4780 Printer prints only blank pages, connected to a MacBook Pro

    My Photosmart C4780 all in one printer which is connected by USB to my MacBook Pro OS 10.6.8 prints only blank pages, and no text; I have turned it on and off; disconnected and reconnected; uninstalled the HP software and reloaded and updated drivers, firmware and patches.  The scan function works and scans the document to my Mac.  The copy function also does not work; when I press the OK function next to the copy icon, nothing happens

    Hi mpmehta
    I understand you are not able to print in black and the copy function isn't working.
    I will be happy to assist you with this.
    Make sure the printer is connected directly to wall outlet. (don't use a power hub or a surge protector)
    Try and print a hardware self test on the printer to find out if it is a hardware or
    software issue. Click Here.
    I have included a document for not being able to print in black.
    Here is a document for the copy function not working.
    If you require further assistance please provide the following so I can assist you better.
    Did the configuration page print?
    Any black print on the page?
    What are the ink levels?
    Are you getting a error when trying to copy?
    Please let me know the results.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • CS4 is adding a blank page, throwing off the printing

    I am creating a 40-page booklet to be printed 2-up saddle-stitch
    In the Pages layout, it says i have 40 pages in 21 spreads. 1 page on the top is the front cover and 1 page on the bottom is the back cover and 19 double-page spreads inbetween. Pages 2 and 39 are the respective inside covers. Page 1 is aligned on the right and page 40 is aligned on the left. It should be printing fine, I would think.
    But in the Print Booklet-Preview Pane, it gives a message that it has added 1 blank page to creat the booklet, and it was added before page one, so I now have no back cover, and my inside covers and page layouts are all wonky now.
    I noticed that in the Pages flyout there is a small square to the right of Page 40, where page 41 would be. A small square that I can't highlight.
    A few more items of interest, all pages have both Allow Document Pages to Shuffle and Allow Selected Spreads to Shuffle checked.
    I am at a total loss. Any help would be greatly appreciated.
    gw

    Keep in mind that everyone here is a volunteer. Most of the regulars, like myself, drop in at least once a day, as we have time, and offer advice and solutions when we have them.
    That said, I saw your post when it first was listed, and saw that you seemed to finding your way, and didn't have anything more to add at that point, as I suspect was the case with a lot of others. I'm sorry it never occurred to me to ask if you had any blank pages in the document, but there was nothing in the original post to suggest that, and including blank pages in a booklet print job is a pretty standard thing to do. If you know enough to have already added blanks to fix the page count, one would presume you also know enough to include them in the print job.
    As far as the forum organization, we're about to go into a new version of the forum software, and many of the regulars are looking on that with some trepidation. Most of us actually LIKE the way things are now -- functional and uncluttered with extraneous nonsense like avatars and ratings points -- but it seems much of that is going to be creeping in. An attempt to unify the Adobe and Macromedia forums last year was an utter disaster, and we've all got our fingers crossed it won't happen again, but we'll be living with it no matter what as the Webcrossing contract is up and Adobe has signed on with Jive. You might want to take another look when the changeover is complete.
    And, I'll repeat, these forums are probably the BEST source of FREE and accurate expert information on Adobe applications on the planet. You'll find users (and even some Adobe employees) from all over the world with vast experience in some pretty esoteric and specialized techniques. I find I still learn something new almost every week, and I've been making my living with InDesign since version 2.0 was released. I hope you'll come back if you have more questions.
    Peter

  • MY PIXMA iP4000 not printing--paper feeds and steps through but only blank pages

    The printer sounds like it is printing----you can hear the print head moving---but nothing prints....
    pages are completely blank. Reseated the connections, no effect. Took out all the cartridges, reseated
    them, no effect. Still only prints blank pages. Connected it to another computer, same---only blank
    pages...nothing, not even a test page or nozzle page will print. Any ideas? Was working fine
    on Monday when I went out of town until Friday. When I tried to print on Saturday morning, only
    blanks pages. Just spent a small fortune on ink for the printer and would hate to trash the
    printer, but can't justify spending more than the price of a new one to have the old one fixed.
    PS The printer is connected to my USB port, as it was for the past several years when it worked
    fine. Totally stumped/

    Thanks, Michael, however, I was on the phone with Canon for some time, and could not get the printer to do anything even off line. Was told the iP4000 is over 8 years old and there are no parts available to repair it.
    So I have already replaced the printer with an iP2702 that was on sale at a nearby
    mass merchandise store. I was intending to replace the iP4000 eventually anyway, as the red was
    not printing as vividly as it once did...more like a purple. Thought at first it was because I was using
    3rd party ink, but even after replacing the magenta cartridge with "genuine Canon", the red was still
    not as vivid as when it was new.
    Unfortunately,as you know,  the iP2702  got uses a more expensive combined color cartrdige
    rather than the separate ones in the iP4000.
    I am suspecting the reported failure of my iP4000 to print may be due to the third party cartridges
    which I was told do not contain a "chip" as do Canon cartrdiges and that may signal to the printer
     to suppress printing.
    Strange, as I have been using 3rd party cartridges for some time prevbiously without any problem.  
    H. Singer

  • I have a large document which keeps repaginating and adding blank pages. I can no longer use the print preview at all. I have tried all the usual fixes. Nothing works. Can anyone help?

    I have a large document which keeps repaginating and adding blank pages. I can no longer use the print preview at all. I have tried all the usual fixes. Nothing works. Can anyone help?

    Is your printer selected? <br />
    Is '''Print to File''' selected, where the web page is being printed to a file and not being sent to your printer?
    See the screenshot below.

  • I am unable to print. Preview shows a blank page and it is blank when printed. I've tried all of the suggestions here. Any other ideas?

    When receiving an email that I wish to print, nothing prints. The Preview shows a blank page and it is, in fact, blank when printed.

    When receiving an email that I wish to print, nothing prints. The Preview shows a blank page and it is, in fact, blank when printed.

  • Hp photosmart 6510 printing and photocopying blank pages even after putting in new ink cardridges

    Hi there, can anyone help?
    My photosmart 6510 has recently started printing and photocopying blank pages.  The ink cardridges were low and I have replaced them with new ones. I have cleaned the printer head and the test comes out in colour.
    I have no idea what to do other than buy a new one !
    Any advice appreciated.

    Hi @TG13,
    I'd like to help. Please begin with the steps in the following document; Printer Prints a Blank Page or Does Not Print Black or Color Ink for the HP Deskjet Ink Advantage an...  < this applies to the 6510, and 6515 too.
    If you complete, or have already completed all of the steps in the document above and the issue continues, my own personal recommendation, not one of HPs, is to use the solution offered in the following video.  I only suggest doing this if the printer is out of warranty; How to fix a HP Printer, not printing black ink and missing colours 
    Based on the comments, it looks like this will help 
    King_Zog wrote:
    I tried most of the suggestions in this thread, but stopped short of disassembling the print head. Nothing worked until I saw the video referenced in Sunshyn2005's message. That did work, but not on my first try. For the second attempt, I left the wet paper towels in place for a couple of hours to really soak the print heads. That did the trick.
    So, thank you Sunshyn2005, for pointing me to the solution.   - Source
    Although the printer might be out of warranty, if the issue persists, HP may be able to offer you something. Maybe they can offer you a discount on an alternate model. If you are in Canada or US call 800 474 6836, or you can Contact HP Worldwide.
    If this resolves the issue, please let me know so we can help others who may be experiencing the same issue.
    Please click the Thumbs up icon below to thank me for responding.
    ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Sunshyn2005 - I work on behalf of HP

  • My HP LaserJet 1018 has started printing only blank pages.

    My HP LaserJet 1018 has started printing only blank pages. 
    Help?
    Using Windows XP (Home Version)
    Product # CB419A

    Could be a number of issues.  First could be a bad or not connecting transfer rollers which moves the toner from the drum to the paper.  Only way to test is a half test by putting paper on the manual tray and printing a self test.  When the back edge enters the printer, open the toner door to stop printing.  Remove the toner and flip back the cover over the toner drum to see if there is any image on the drum.  If image is present then it could be transfer roller issues.  Use the service manual and look under engine diagnostics in the index and it will direct you to a page that shows how to perform an engine test.  Do the test to see if you get a sheet of paper with lines on it.  If you get lines, then the issue could be the formatter.  If no lines and the shutter has been removed then I would think you are having high voltage issues.  You may have to bring the printer in for service.

  • Creating a template in Pages is straight-forward as answered here previously. Is there and equivalent for iBooks Author which can start with a blank page and build up the template as required? or can one only adapt a ready made template?

    Creating a template in Pages is straight-forward as answered here previously. Is there an equivalent for iBooks Author which can start with a blank page and build up the template as required? or can one only adapt a ready made template? This has proved unsatisfactory to me so far. Lines are left in etc.

    There are two basic menus for fonts - one from the main menu bar and one from the toolbar. You can also bring up the font manage dialog.
    I don't recommend trying to hard to force an otherwise foreign font, as it inevitably needs to be usable/supported on iOS as well, and that can get tricky w/3rd party fonts, as an example, even with the expanded font support in the latest iBA.
    If you need to discuss fonts more, I suggest starting a new thread....preferably with a slightly more brief title, thanks.

  • Only blank page printing

    We have a Ricoh Aficio MP C2000 , there is only one page with somthing and then he print only blank pages till box is empty

    Hello there, fritspen.
    The following Knowledge Base article offers up a great, in-depth list of steps for troubleshooting issues with printing in Mac OS X:
    OS X Mavericks: Solve printing problems
    http://support.apple.com/kb/PH14142
    Thanks for reaching out to Apple Support Communities.
    Cheers,
    Pedro.

  • HP 6510 printing only blank pages after changing print cartridges

    Hi,
    My HP 6510 is printing only blank pages after I installed new print ink cartridges. I tried cleaning the print heads, aligning the printer... which did result in some pages printing with a little color (but it seemed "off" to me). That said, when I try to print a regular document from my PC it only prints a blank page. 
    I can't seem to figure this one out on my own - please help!
    Thanks!
    Chloe

    The document here may help resolve black not printing on your Photosmart 6510.  Be sure the cartridges are vented as shown in solution two.
    Is your printer still in warranty? You can check with HP's warranty tool here.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • I am using window.print() to print the data of my webpage, it prints only first page and left the remaining while it works fine with IE and Google Chrome, ie print all the pages.

    My Page has data more than one page, it has verticle scroll bar to view all data .
    I used window.print() to print the data of webpage, but it prints only first page and left the remaining information.
    This works fine with Internet Explorer 6+ and Google Chrome.

    Does the entire webpage appear in Print Preview? <br />
    File > Print Preview

  • Open e-mail only get blank page and header

    open e-mail and only get blank page and headers please help

    hi thanks for your reply no it's not all that was sent to us we have about 24 and only a few will open properly. i was told it could be something to do with aol pop. our outgoing mail server just says mail. and then our name.

Maybe you are looking for