I am unable to access internet when server app is running on mac mini
I recently installed the server app on a mac mini. With the app open, I am unable to connect to web pages through the mac mini. I do not have this connection problem with the server app closed. While I can see my IP address I am also not able to connect to the server. Would love some advice how what I am doign wrong with the setup.
My ISP is a DSL through century link, the mac mini is hooked to a cisco E4200 v2 wireless router.
You'll need to go through the configuration of the server, sounds like something is off.
Have a look at this site http://www.mountainlionserver.com as well as the Apple support articles.
Similar Messages
-
Domain Joined Workstations Can't Access Internet When Server is Off
I have two Windows 7 Ultimate workstations joined to a server running Server 2012 R2 Foundation. Whenever the Server is powered off the workstations can't access the internet via a web browser from neither a domain account nor a local
account, even though the network icon in the system tray indicates "Internet Access".
Is this a normal situation, or am I missing some settings? This is a big problem because there are times when the server will be off, but the workstations still need to be able to work in a web browser.
I'd be very grateful for a solution to this problem.
Capt. DinosaurHi again SenneV, and thanks for the fast response; I wish the Dell community would get back even half that quickly.
"No i mean that after a while, the nla status icon on system tray will no longer state there is internet acces while there isn’t."
I was afraid that's what you meant, but I wanted to find out for sure.
"I would recommend doublechecking the bios and management ui for power options as I cannot imagine a server that would not be configurable to boot after power loss."
I couldn't imagine that either, but I've checked several time, and unless the setting is in Aramaic or mentioned in the Rosetta Stone, I couldn't find a setting for that. There is a setting for restarting after a crash,
but not just for a return after a power failure. I have the server on a battery backup so that it doesn't crash when a power failure occurs, but I can't even coax the server to restart after power is restored.
The server is a Dell PowerEdge T110 II, and it has BMC in the BIOS in which I've made all the necessary settings. Unfortunately BMC doesn't have a web GUI like IDRAC, and only (supposedly) responds to IPMI. However, I've not been able to get
that to work either. I've downloaded Intel's "ipmiutil" and installed it on one of the workstations and the server, but I can't get the utilities to work. I feel like I'm in the twilight zone.
I've posted questions on the Dell Community, but as yet (after almost a week) not a peep out of anyone there. I guess I'll have to contact Dell Tech Support.
Anyhoo, thank you for your help. I do appreciate it.
P. S. I tried logging into the workstations via LogMeIn while the server was shut down, and guess What! It worked. I was able to access both workstations even though the server wasn't running. Now, if I can just get IPMI/BMC to work,
my problem w/be solved.
Capt. Dinosaur -
Unable to access internet when static IP address is configured
Hi
I am facing the problem for not getting the internet in AD Server(DC) if configured with static IP address. If we set DHCP it will connect to internet. When I check the IPCONFIG on DHCP settings its showing the external address of the ISP router. Not the
firewall. Suspect there must be a foul play with DNS. Appreceiate your prompt response.
Thanks
MichaelHi
First, Disable ipv6. then run the netsh command to reset IP stuff. Just a warning though,
I think this will only apply to this problem if you are using static IPs.
Here is the netsh comman:
netsh interface ip set address name="Local Area Connection" static xxx.xxx.xxx xxx.xxx.xxx xxx.xxx.xxx
ip address subnet mask gateway
http://www.santanunayak.com An MVP From Microsoft -
Hello,
I created an application in Flash CS5.5 using Adobe Air 2.6. When I test the app on my computer (where it was written) everything works fine. When I publish the application and run the .AIR on my computer everything works fine as well. The issues comes about when I attempt to install and run my AIR application on a Mac operating system. In this case when the application runs some graphics are visible while some aren't. Some movieclips/buttons are visible while others aren't. One example of this is the buttons. None of the buttons in the entire application are visible. When the user clicks the area where the button should be the button click event is fired and the app acts accordingly (i.e. the main menu button which can't be seen still sends the user to the main menu). What could be the problem?
I had thought of just converting the application to strictly Flash without AIR but I require AIR for the file system api as well as a couple other api components.
Thank you in advance,
NoahHi Noah,
I don't think I've run across this before. I'd be willing to give it a try on my system if you'd like (you can email me at [email protected]). Though I suspect this is a project specific issue, it also can't hurt to open this as a new bug over at bugbase.adobe.com.
Chris -
I had to restore my i pad to delete restrictions on facetime. I am now unable to access internet banking with Natwest due to my browser not being supported? How do I correct this? It was working ok before i did the restore. Thankyou.
You are most welcome
-
I am getting error messages when importing CD's. I keep getting a message saying 'unable to connect to CDDB server'. I run itunes on a macbook pro. Any ideas/solutions?
Don't worry I've sorted it! I just had to turn off Reminders as well in iCloud. Calendar then worked fine, even when I turned Calendar and Reminders back on.
-
I have 3 iPhone5's with ios 6.1.2 that user cellular data when connected to wifi. Every hour to the minute even when no apps are running, iCloud is off, Ads are off, Diagnostics are off. Running on AT&T cellular network.
Date Time To/From
Type
Direction
Msg/KB
03/14
01:30 PM
phone
Internet/MEdia Net
Sent
78 KB
03/14
01:02 PM
phone
Internet/MEdia Net
Sent
4397 KB
03/14
12:48 PM
phone
Internet/MEdia Net
Sent
19520 KB
03/14
12:30 PM
phone
Internet/MEdia Net
Sent
19503 KB
03/14
11:30 AM
phone
Internet/MEdia Net
Sent
2427 KB
03/14
10:30 AM
phone
Internet/MEdia Net
Sent
359 KB
03/14
09:30 AM
phone
Internet/MEdia Net
Sent
1396 KB
03/14
09:25 AM
phone
Internet/MEdia Net
Sent
1 KB
03/14
08:25 AM
phone
Internet/MEdia Net
Sent
30 KB
03/14
07:25 AM
phone
Internet/MEdia Net
Sent
16 KB
03/14
06:25 AM
phone
Internet/MEdia Net
Sent
45 KB
03/14
05:25 AM
phone
Internet/MEdia Net
Sent
15 KB
03/14
04:25 AM
phone
Internet/MEdia Net
Sent
14 KB
03/14
03:25 AM
phone
Internet/MEdia Net
Sent
21 KB
03/14
02:25 AM
phone
Internet/MEdia Net
Sent
23 KB
03/14
01:25 AM
phone
Internet/MEdia Net
Sent
16 KB
03/14
12:25 AM
phone
Internet/MEdia Net
Sent
23 KBHello All Who Read This!
I just bought an iPhone 5 on the 21st of March. I ate through 850 MB's in 12 days. I read up on the issue of data consumption looking for tips to conserve data. I did not know there was a problem.
This morning I found out that I was leaking data very little, but daily it accumulates. I am in Barcelona, Spain. I do not have a contract, I am on a prepaid Yoigo carrier.
I happened upon an article/blog by Robert Parks at snnyc.com "problems persist in ios 6.1.2.".
Although his situation did not relate to me, I tried a few tests on my own to see if I could stop the data leak without turning off my celular data and possibly push notifications, I think I found a solution that might help someone:
In ios 6.1.3 goto Settings/Mail, Contacts,Calenders and scroll down to Calendars and turn off " New Invitation Alerts" and also turn off "Shared Calendar Alerts".
My Cellular Network Data seems to be behaving. I only see a change in MB used when I open an ap that uses data.
All The Best -
attempted to mail an email with a large attachment file. One of the addresses was bad. When my Outlook is running, the Mac tries to send it and shows the progress. However, when I look in my Outbox the files are not there. It does show up in the Outbox progress section but I can not delete it when it is there.
Where do these files reside?
Is there a hidden Outbox??
MacBook Pro, Mac OS X (10.7.1)If you think getting your web pages to appear OK in all the major browsers is tricky then dealing with email clients is way worse. There are so many of them.
If you want to bulk email yourself, there are apps for it and their templates will work in most cases...
http://www.iwebformusicians.com/Website-Email-Marketing/EBlast.html
This one will create the form, database and send out the emails...
http://www.iwebformusicians.com/Website-Email-Marketing/MailShoot.html
The alternative is to use a marketing service if your business can justify the cost. Their templates are tested in all the common email clients...
http://www.iwebformusicians.com/Website-Email-Marketing/Email-Marketing-Service. html
"I may receive some form of compensation, financial or otherwise, from my recommendation or link." -
when using apps or running safari my iphone glitches then takes an age to reboot,done a full restore but still getting same problems any ideas
The Basic Troubleshooting Steps are:
Restart... Reset... Restore from Backup... Restore as New...
If you have tried all these Steps and you still have issues... Then a Visit to an Apple Store or AASP (Authorized Apple Service Provider) is the Next Step... Be sure to make an appointment first...
See if there is anything here first to help with your issue...
Troubleshooting applications purchased from the App Store -
HT201335 why can't i get sound when I mirror from the latest mac mini?
why can't i get sound when I mirror from the latest mac mini?
if you have sound icon on your menu bar: press alt on your keyboard and click mouse on sound icon - check is the correct audio output is selected.
If you do not have this icon: System preferences > Sound > Output and check audio output -
Close Mac Server App still run?
Hello, if I close my Mac Server application (I have a mac mini) will my websites still run? Or does the app HAVE to be open?
You do not have to have Server.app running all the time. Your websites and all the other services will keep running in the background.
In fact it is firstly best not to leave Server.app running all the time because it will after a period often get confused about the status of the services, and secondly this can be a security risk as it makes it available to anyone else. It is also for the same reason not necessary or desirable to even have a user logged in on the server. The services do not need this. -
Unable to Access Internet Despite Adapter Showing "Connected".
Hi, I have a Lenovo "G"-Series notebook, Type 4446-38U which has suddenly stopped allowing me to access my internet connections. The PC is only about a month old. It is running XP Professional.
I have three connection options: 1) dial-up (using an onboard HDAudio Soft Data Fax Modem with Smart CP); 2) ethernet or Local Area Connection (using an onboard Broadcom Netlink Fast Ethernet); and 3) wireless (using an onboard Intel WiFi Link 5100 AGN) -- none of these components are showing that they have conflicts/problems in the System Properties/Device Manager.
At my home, which is located in a rural area where I can only get dial-up, I tried checking my e-mail last week (with Mozilla Thunderbird), but received an error notice stating that the e-mail server could not be found; it was the same issue, when I tried to get Norton virus updates (Internet Security 2009), XP updates on the Microsoft website (using Microsoft Updates with Internet Explorer), and simply accessing the web (using Mozilla Firefox) -- i.e., "Server Not Found." The odd thing is that I can not only hear the connection being made by the modem, but can also see that the device is 'Connected', when I check the connection in Control Panel/Network Connections. The following day at my office, I checked the other connection options (ethernet & WiFi), and found that I had the same problem -- i.e., they were shown as "Connected" in Control Panel/Network Connections, but I was unable to access anything on the web (e.g., e-mail, Google, virus/Microsoft updates, etc.). It's as if there is something blocking the internet connection to these programmes/utilities.
When I ran the Microsoft Networking Troubleshooter ('Diagnose Network Configuration & Run Automated Networking Tests), all the Network Adapters were shown as having passed. Ditto, when I ran the "Test a TCP/IP Configuration Using the Ping Command" -- pinging 127.0.0.1, the results showed 4 packets sent and 4 received.
I spent several hours on the phone with Lenovo Tech Support to no avail, and their instruction that I uninstall Norton Internet Security made no difference either. When they instructed me to open a Command Prompt and ping 192.168.1.1, the results showed that there were 4 packets sent and 4 received. When I was instructed to ping the IP Address for the wireless adapter, the results showed 4 packets send and 4 received. When I was instructed to ping www.google.com, the results showed that the ping request could not find the host www.google.com. Lenovo Tech Support stated that there was nothing further they could do, and that I needed to use a utility to set everything back to factory specs (i.e., have a utility programme erase everything on the hard drive and reinstall XP ... and even then I was told that there was no guarantee that would fix things, meaning that the PC would then have to be sent into their repair depot). Before I do this, I was hoping that someone here might know as to what's going on with my connection problems and how it could be fixed, without having to erase everything.
I would appreciate any insight or advice anyone might have. Thanks so much!
~ JackI did do a complete uninstall of Norton (i.e., didn't save any of the settings), but that didn't resolve the connection problem. I also turned off Microsoft's firewall as well, once Norton was uninstalled (it had been turned off, when Norton was installed, and once Norton was uninstalled, MS firewall defaulted back to an on/active status).
I also forgot to mention in my initial description of the problem and actions taken thus far to try and correct it, that I additionally tried the "ping" procedure described in paragraph five above in Windows Safe Mode with Networking, but was still unable to connect to the internet. -
Unable to access Internet from LAN - Cisco ASA 9.1(2)
Hi,
I have Cisco 5515 IOS 9.1(2). I had configured out-to-in rule with 'ssh' and able to access the Internet server, but the same server is unable to access the Internet. Not sure what i am missing here. Please look in to the configuration below and suggest.
10.4.20.2 is the host i am trying to access the Internet and it fails, but able to 'ssh' to this IP from the internet.
ASA Version 9.1(2)
interface GigabitEthernet0/0
description OUTSIDE
nameif outside
security-level 0
ip address 1.1.1.1 255.255.255.248
interface GigabitEthernet0/1
description BACKUP
nameif backup
security-level 0
ip address 2.2.2.2 255.255.255.248
interface GigabitEthernet0/4
description INSIDE
nameif inside
security-level 100
ip address 10.4.20.1 255.255.255.0
boot system disk0:/asa912-smp-k8.bin
ftp mode passive
clock timezone PT -8
clock summer-time PT recurring
dns domain-lookup outside
object network 2.2.2.4_10.4.20.2
host 10.4.20.2
access-list out2in extended permit icmp any any inactive
access-list in2out extended permit ip 10.4.20.0 255.255.255.0 any
access-list out2in_bkp extended permit icmp any any inactive
access-list out2in_bkp extended permit tcp any object 2.2.2.4_10.4.20.2 eq ssh
pager lines 24
logging enable
logging timestamp
logging standby
logging monitor debugging
logging trap debugging
logging history debugging
logging asdm debugging
mtu outside 1500
mtu backup 1500
mtu inside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-713.bin
asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network 2.2.2.4_10.4.20.2
nat (inside,backup) static 2.2.2.4 net-to-net dns
access-group out2in in interface outside
access-group out2in_bkp in interface backup
access-group in2out in interface inside
route outside 0.0.0.0 0.0.0.0 1.1.1.2 10 track 100
route backup 0.0.0.0 0.0.0.0 2.2.2.3 20 track 101
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 0.0.0.0 0.0.0.0 outside
http 0.0.0.0 0.0.0.0 backup
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
sla monitor 100
type echo protocol ipIcmpEcho 8.8.8.8 interface outside
sla monitor schedule 100 life forever start-time now
sla monitor 101
type echo protocol ipIcmpEcho 8.8.4.4 interface backup
sla monitor schedule 101 life forever start-time now
service resetoutside
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
track 100 rtr 100 reachability
track 101 rtr 101 reachability
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 0.0.0.0 0.0.0.0 backup
ssh timeout 60
ssh version 2
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 123.108.225.6 source outside
ssl encryption rc4-sha1 aes128-sha1 aes256-sha1 3des-sha1
username xyz password ***** encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:9b63e3cfc9f98800d2bb3efa34c75906
: endHi Anand
Could you please do a packet tracer on the Asa?
Packet-tracer input inside icmp 10.20.4.2 8 0 4.2.2.2 detailed
Are you able to ping 4.2.2.2 from the server ?
Please use the following command
"fixup protocol icmp"
And then check whether you are able to ping the Internet.
Regards
Aditya -
I have my router, modem, and computer all set up correctly. I can access the internet in this setup but with only the computer that is connected with the ethernet cord to the router. Yet, my WRT54G router can't connect to the internet in the Linksys easy setup nor through the http:192.168.1.1 method.
When I changed the internet connection type to PPPoE, my modem was unable to access the internet. I also changed the IP to 192.168.2.1 but that didn't help. I have performed several power cycles. I have upgraded the firmware.
I changed the internet connection type back to DHCP, so I am able to come on this website, but I can't set up the wireless since the router says it can't connect to the internet. Please help!Start it from scratch...Reset your router and re-configure it...
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page.
If your Internet Service Providor is Cable follow this
If your Internet Service Providor is DSL follow this
To change the Wireless Settings click here and Enable Wireless Security
Now see if you can locate your wireless network on your wireless computer and attempt to connect... -
Unable to access Internet using a Mobile Network
Hello friends
I recently updated my SE Xperia mini pro 17i (2011 model) to ICS, initially there were some issues and I had to re-update it to finally get authentic interface of ICS. Even after the successful update I am unable to use the mobile network to access Internet, the only way is to use a Wifi instead. Can somebody please help me out with this issue?
KaranThe first thing I would advise doing is contacting your current network provider and have them send you through the relevant internet settings.
What are your thoughts about this forum? Let us know by doing this short survey.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.
Maybe you are looking for
-
Dear Sir / Madam I WANT TO USE HP1020 PLUS LASERJET PRINTER WITH B& R PC . PC HAVING TWO FLASH CARD EACH HAVING MEMORY OF 1GB. WINDOW XP EMBEDDED SERVICE PACK-3 How much memory will be covered during printer driver installation.
-
Can't play video on certain sites,
The following is what comes up in the error console when trying to play video on as far as I know just The Weather Channel, unexpected css token: : Failed to load resource: the server responded with a status of 404 (Not Found) [Error] TypeError: und
-
MS Word prints only blank document
I rarely use MS Word anymore. I use Mellel - except Word (10) does such an easier job with tables. I created a two-page table. It prints out blank. I tried 3X, it would not print to pdf even.
-
Can we broadcast our video in HD Quality through FMS? if possible what we have to do for that, whats the minimum bandwidth needed to deliver the HD quality video?
-
Hi all, i have created an Infoset on 2 ODSes. i have created a query based on this Infoset. i have a requirement where i want data only from these ODSes to be given in the picklist of the selection screen. I have changed the property "Query Exec.Filt