I am unable to switch on/ off my wifi
I'm unable to switch on /off my wifi, any helps?
Also I'm having problems through my camera ,when I open my camera app
And capture a picture the app automatically switches off,also the captured pic is not saved,
Any helps on this?
Try a reset. Hold the Sleep and Home button down (together) for about 10 seconds until you see the Apple logo. Ignore the red slider.
Similar Messages
-
Iphone 5 Unable to switch on/off
Hi,
for quite sometime my IPhone 5 on/off switch has stopped working; can anyone advice if this matter can be repaired?
I popped in the London apple store but they asked me a fortune to repaired which quite frankly its probably not worthy.
any advice of best practice?
Thanks
SYou can also check on Apples site to see if your iPhone 5 qualifies for the power button replacement program. You put your serial number in, and it will tell you if that particular phone is eligible for a FREE button replacement. So that would be better than taking it to some dodgy backstreet phone repairer. I know, as mines in at the minute getting replaced, and as a bonus, they will swap your battery too at the same time. so according to the invoice I'm getting a new power button and battery for nowt. Not bad customer support for a 3 year old phone is it? Amazing actually springs to mind.
And as a bonus, they will loan you a phone to be going on with, as it takes about 5 days to do the repair. -
Sony Xperia Z1 No Alarm Display and Unable to switch off alarm
Eversince I had the first Android Kit Kat update, my Xperia Z1 C6903 was not able to hear any notification sounds, my alarm sound worked but unable to switch it off or delete it and when my contacts call me, it send it straight to voicemail and I don't even hear the notifcation call sounds either. Did a reboot and went on safe mode, I still had the same problem. Found out online that there is a sound bug with my current firmware version: 14.3.A.0.681.
When the new update 14.3.A.0.757 was available, I downloaded it. After this, my sound notifications worked fine, however, my alarm is still not working. Both on normal and safety mode, my alarm does the following:
1) The alarm sound works
2) Side key behaviour does not show up on my screen, so I am not able to dismiss my alarm
3) I manually go to my "Alarm and Clock" app and press the "OFF" indicator. Alarm sound does not stop.
4) I have to go to > alarm settings >Delete alarms >Choose the current alarm to delete > Alarm Sound then stops.
This has been happening eversince the Android Kit Kat version was available for download (the previous and current one). I have reboot my phone, gone on safety mode, I have gone to >Settings >APPS> All> Clock > Clear Data, and went to the Sony PC Companion > Support Zone > Repair phone/tablet, as well as deleted all my apps.
I do not know what else to do. I can only conclude that this is an existing problem with the new software update. I need my alarm working or else I am unable to get up for my morning meetings. PLEASE HELP!so i have been having the exact problem on my Z1. the alrm goes off at the right time....the notification works perfectly but you just cannot switch it off or snooze it. if i go to the drop down menu the active alarm is not listed there...the side buttons dont work or have no effect even when configured.
you literally have to power the phone off for it to stop sounding. this is really annoying and i notice that teh last comment here was a month ago and Sony have still not addressed this problem. if you google this issue there a stacks of people with the same problem and more frustarted as we keep getting suggested fixes like clear clock cache which EVERYONE knows will not work as the problem is not with the data of the alarm....its a bug in the software that prevents the app from excuting teh way it was intended to.
my alarms worked perfectly fine before teh update was applied. ever since teh update i ahev had this problem. i dont believe that a solution is to install another alarm app from google play store. i bought the phone which advertises the alarm as a feature and if sony cannot fix or address this probelm then you have falsely advertised...
i am a sold out sony fan...i will never purchase any other brand of phone based on my past experience with sony products but this problem is making me think otherwise. give us a proper fix for this alarm issue and dont treat us like ignorant fools with your suggessted fixes like start in safe mode or reboot your phone....that will never ever fix the problem....its just a way of avoiding the fact that you dont know what to do to fix this problem... -
my iphone froze last nite and i was unable to exit the app i was on, it then switched the screen off as if it was not in use, now i am unable to open my iphone or switch it off, calls are still comin thro as phone is vibrating but im unable to answer as cant activate the screen?????
pls helpSee Here for > Frozen or unresponsive iPhone
Try this First...
Press and Hold the Sleep/Wake Button and the Home Button at the Same Time...
Wait for the Apple logo to Appear...
Usually takes about 15 - 20 Seconds... ( But can take Longer...)
Release the Buttons...
http://support.apple.com/kb/ht1430
More Info here...
https://discussions.apple.com/message/19521062 -
my iPhone 4 has switched off for no reason, and now I am unable to switch this on again???if anybody could help about a reboot tip , he's welcome, many thanks...
1. On your iPhone 4 press and hold both the button and the Home button for about ten seconds. After ten seconds you should see the Apple logo showing up.
2. Now try to run you phone again and see if it works.
If a hard reset the still can't get the device back to a working order.
1. Plug in the device to the cumputer and start iTunes.
2. Press and hold the Sleep/Wake + Home for 10 seconds.
3. Once you see the Apple Logo appears, release the power and continue to hold down the home button for about 5-10 seconds. Look iniTunes and see if your device have shows up.
4. iTunes will notify you that you are now in Recovery mode. Click on OK to continue with the restore process.
5. Next press and hold on the SHIFT button and click on the Restore button. Select the latest IPSW file and the prompt appears.
6. iTunes should now attempt to get your device back to the manufacturer setting.
7. iTunes will later give you an opportunity to restore you content from the PC. Every time when you do a sync, iTunes makes a backup so you can choose the latest backup from the sync. -
I am unable to switch off Passcode on my ipad3. The button for switch off Passcode is greyed out.
I am unable to switch off Passcode on my ipad3. The button for switch off Passcode is greyed out.
Hello again,
I have managed to disable the Passcode.
I checked and I removed a profile that was linked to a business app.
I think it must have been security policy through business app that didn't work anyway.
Thank you very much for taking the time to attempt to resolve my issue.
Keep up the great work!!!!!!!!!!!!!!!!! -
HT201401 i am unable to switch off iphone with the power on/off button.
i am unable to switch off iphone with the power on/off button. Though I can feel the sense of the button, but it doesnt work.
If there is Warranty or AppleCare make Genius reservation or set up service and take or send to Apple for resolution. If no coverage, Apple charges $199 for Replacement iPhone 4S. You can use Assistive Touch. Settings App > General > Accessibility > Assistive Touch > ON > tap new white screen button > Device > Lock Screen. This can be used to turn iPhone OFF, hold down on the Lock Screen icon until "slide to turn off" appears. To turn iPhone ON, connect to power, charger or USB port of computer.
-
Unable to Switch Audio Sync Settings
Hey everyone,
I'm trying to create an animation based off of a 5-minute mp3 audio recording. I need to be able to switch my audio sync settings to Stream so that I can preview audio anywhere in my animation. Currently if I press play just anywhere in the animation it doesn't play the audio. I have to play from the beginning to hear.
After doing some searching on the Internet, I figured out I have to switch my audio sync setting to Stream so that I can play audio anywhere in the timeline. However, the only option I have available is Event. The other ones are greyed out, as the screenshots below testify. Any help would be appreciated. Thanks!
Hardware and Software Statistics:
Adobe Flash Professional CC (CS6) - Version 13.1.0.226
Windows 7 Home Premium - Version 6.1 - Build 7601: Service Pack 1
Intel Core i7, 4GB RAM, NVIDIA GeForce GT 525MThe first the thing a person should always do when they encounter a problem is restart their computer. No worries, I did that.
I tried converting the file to OGG and WAV to see if it would work better. Apparently Flash Professional handles WAV fine, allowing me to switch between Stream and Event audio sync settings. That's kind of strange, because WAV files are so huge and aren't practical when developing a game or something like that.
Thankfully, I'm just using Flash Professional to export a video, so I don't care about file size, but it's a disturbing bug.
If anyone knows why I was unable to switch to Stream audio sync settings with MP3 files, please speak up. -
HT201412 my wifi switched itself off and i cant get it to switch back on. Any suggestions?
my wifi switched itself off and i cant get it to switch back on. Any suggestions?
Hi JoJo_85,
If you are unable to turn on Wifi or the setting is greyed out, you may find the following article helpful:
iOS: Wi-Fi settings grayed out or dim
http://support.apple.com/kb/ts1559
Regards,
- Brenden -
Hey
I don't know if my mac book air is frozen, but the screen is gray with the apple logo in the middle of the gray screen, with the 'booting' icon turning round and round. I have switched it off fron both the power and power button on the computer, it goes off, when I put it on, same screen comes on again. Help Please!Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 3
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 4
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 5
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 6
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 7
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 8
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 9
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 10
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 11
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
unable to switch on my iphone
RESET DEVICE
Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost). -
Iam unable to switch using the stop button in IPOD
whenever a song/video is played iam unable to switch off the IPDOD but if press the menu button for some 6 seconds and then press the hold button iam able to switch off.If the song/video is not played then if i press the hold button iam able to switch off without any problem.
When a song is NOT playing, press and hold the Play/Pause button. THis is how you shut off the iPod. Then, you can engage the Hold switch to ensure you don't accidentally turn it back on.
CHeers
!-Bryan -
when i watch videos on my iphone 5 my wifi buffers the video and then halfway through it just stops and all wifi stops working on my device. i need to switch back off and on the wifi then it works but the same thing happens every time for videos. NOT A ROUTER PROBLEM. all my other apple devices dont have this problem
iOS: Importing personal photos and videos from iOS devices to your computer
iOS: Unable to import photos or device not recognized as a camera -
How to switch on / off data service to Vivaz?
While I was abroad, I experienced data roaming which is charged per KB, when I was connected to WiFi in my vicinity. I would like to know how to switch on / off data service by changing settings on my phone, SE Vivaz.
Solved!
Go to Solution.Hi,
There is no way to simpy switch data off and on with the Vivaz handset I'm afraid. However my best suggestion would be to create a dummy data account on the handset. If you set this as the account you wish to use when browsing the Internet through your network operator, it will be unable to connect. If you are using Wi-Fi, this will mean that if you go out of range, the handset will not be able to switch to your mobile network data.
This can be done by following these steps:
Settings > Connectivity > Destinations > Access Point > Add New > Packet Data > Name the account (for example, Dummy account) > Select Internet.
Once set up, go into Internet within Destinations and set the dummy account as priority 2 for Internet behind your Wi-Fi connection.
I'd also recommend tapping your Data Internet connection, selecting Edit and ensuring 'Use Access Point' has 'After Confirmation' written under it. This will ensure you are asked if you wish to use that connection before it automatically connects.
Let me know how you get on -
My iphone 4 unable to switch on
my iphone 4 automatically switch off and unable to switch on.
Do a reset hold down the home/sleep button until you see the apple logo and then release, then wait for the phone to boot back up.
Maybe you are looking for
-
Itunes and vista error message
I just purchased a new computer with vista and now my ipod/itunes won't work. i have upgraded to the itunes 7.1 (i think) and at first- my itunes synced with my ipod nano, and now it won't...error message (-50) An unknown error occured. And then it s
-
I recieved my iPhone 5 3 weeks ago and the battery life completely *****! After doing a few things and maybe using it for about 30 minutes the phone start overheating like crazy then the battery starts dropping very fast. Does anyone know if it's a p
-
How to reset?"Enter Administrator Password" on Compaq CQ62. System disabled key 75858185
Hello everyone, I have a Compaq CQ62. When I've turned it on, it comes up with the bios screen message "Enter Administrator or Power on Password". I tried a few incorrect attempts and after the third attempt, a message "System disabled - Key 75858185
-
OUTPUT OF BLACK CARTRIDGE OF hp officejet 6500A
Myprinter is HP OFFICEJET 6500A. All other three cartridges color output cyan, magenta, yellow are coming fine, but I am not able to get outputprinting of black cartridge even after sincere trials after making default factory made setting and loadin
-
Multi-language Package for BlackBerry
Hi, Guys, Do you know where I can download Chinese language packages for the BlackBerry ? Thanks