I bought a 364 XL cartridge for my Photosmart 6510 printer, but it doesn't fit.

I bought a 364 XL cartridge for my Photosmart 6510 printer, but it doesn't fit—it's too wide. Yet the User Manual I downloaded from HP (helpfully called c02983796) clearly shows an illustration of the XL cartridge fitting in the printer. Advice?
This question was solved.
View Solution.

Hi,
The HP 364 XL Black ink cartridge been updated in September 2010.
Take a look in the following document:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02750681&lc=en&cc=us&dlc=en
If your ink cartridge is the older ink cartridge you shoulf contact the retailer to replace it.
Regards,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Similar Messages

  • New cartridge for HP Photosmart 6510 appears faulty

    I have just replaced the old magenta cartridge in my HP Photosmart 6510 printer with a brand new one, from a 4-pack, and it is now telling me that one or cartridges appears to be missing or damaged. The new catridge appears fine and is vented, and repeat re-installations or switching off the printer do not help.  I have tried cleaning contacts but all looks very clean. I managed to get the printer working again with the old magenta cartridge until that definitely ran out, but now the same error is detected, leaving me with a printer which will not work even to print black-only.  I bought the original cartridge as part of a 4-pack from Amazon, so have little chance of returning the fauly cartridge (even if they accepted it was faulty).  Looks like I will have to get a new magenta one and hope that works, but in the meantime, has anyone any ideas how I can persuade the printer to work using just black?

    Hello,  There could be two possibility for this issue,  Ink cartridge that you bought or the Printhead .  Try installing the old cartridge and check if the error shows up.If yes, then its an issue with the printhead, and the printer need to be replaced as the printhead is fixed part in this printer. If No, then the new cartridge is a faulty one, contact HP Tech Support for further assistance. If the new cartridge is HP Genuine, then iam sure Tech Support should  help you out in getting the cartridge repalced ( if you are in USA ). Please call HP Tech Support for further assistance.
    If you are in US , the toll free # is 1-800-474-6836 .
    If you are not in US , then log on to www.hp.com , at bottom-left corner there is a world map icon, click on it and then select the region you belong to, which would then provide support options for you for that region.

  • I started using LT 4 and I have a serial number, also upgraded to LT 5 and have a serial number. Now I just bought a new Macbook Pro and installed the LT 5, but it doesn't accept my serial number. Why?

    I started using LT 4 and I have a serial number, also upgraded to LT 5 and have a serial number. Now I just bought a new Macbook Pro and installed the LT 5, but it doesn't accept my serial number. Why?

    When you installed the Lightroom 5 on your MacBook, did it ask for both serial numbers. Since you purchased Lightroom 5 as an upgrade, you need both the serial number from your original purchase as well as the new serial number for Lightroom 5. If you have both of those numbers and they are still not being accepted then you will have to contact Adobe customer support for a solution.

  • My Ipad2 won't turn off.  I've tried the reset method,  holding both buttons down for at least 10 seconds, but this doesn't work. I'm on version 5.1.1 and all other functions work except that I cannot get onto the internet via wi-fi either.  Help ??

    My Ipad2 won't turn off.  I have tried the reset method by holding both buttons down for at least 10 seconds, but this doesn't work.  I can't get onto the internet via wi-fi either (don't have a 3G card fitted).  All other functions seem to be working OK including charging. Not had this problem before, but I recently upgraded software to 5.1.1 so is there a bug in there somewhere?

    Look at last link.
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130?tstart=60
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • I just bought a macbook air, I want to cut en paste, but it doesn't work, how can I fix this?

    I just bought a macbook air, I want to cut and paste but it doesn't work.  How can I fix this?

    that all works, no problem. but if I want to devide my songs per genre, it doesn't work.  in itunes you find cut, but I can't select it.  I just can copy my songs or photos.  So I've got everything twice.  Can you explane me how I can do that? cause it's my first Apple computer

  • I buy Creative Cloud single-app membership for Illustrator (month-to-month), but it doesn't adjust my PC(Microsoft windows XP) SO YOU HAVE TO REFUND

    i buy Creative Cloud single-app membership for Illustrator (month-to-month), but it doesn't adjust my PC(Microsoft windows XP)
    SO YOU HAVE TO REFUND
    I alreagy finished the credit card payment.

    Hi There,
    Kindly contact our support team to get the subscription cancelled via: Contact Customer Care.
    Thanks,
    Atul Saini

  • Need driver for HP Photosmart 1115 printer for windows 7 beta

    What driver can I use to get this printer to work?  Can you also provide installation procedure?   Would your recommendation also work for HP Photosmart 1215 printer which I also have?
    Thanks

    Had the same problem, got it working by using Photosmart 8200 driver.   You have to go to add a printer, select Dot4 USB for the port, and then pick the 8200 driver from the list that Windows 7 ships with.   Once you do, it just works.   My test page printed on the first try.   HP could make this a *lot* easier for everyone, but I guess they are in the business of selling more printers.

  • Photsmart 5520 gives message cartridge for older generation of printer

    I only use hp cartridges and these are all 364 as used on my previous 5520!
    But the message says cartridge for an older generation of printer
    Help

    Hi,
    The HP 364 ink cartridges only have the warranty end date listed on it, it never list a manufacturing date.
    Follow the guidelines below, the Do I have the updated cartridges? section explain how to identify an updated cartridge, either with its packing material or without it:
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c02435884
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • Setup cartridge for the Photosmart 7520.

    My question is about the setup cartridge. After the initial setup, do you leave that cartridge in or take it out? When I check my ink levels, it's the only one that shows LOW....is that normal?

    Hi,
    The setup cartridges are sent to initialize the printer when you install it for the first time. And these are complimentary cartridges sent along with the printer so it won't have much of ink compared to a normal ink cartridges and it is perfectly fine and use the cartridges until it is completed out.
    Thanks.
    I work for HP.

  • HP6520 How can I use a new, but protected, 564 XL ink cartridge from my broken 6510 printer.

    My 6510 failed after just over one year of use.  I salvaged a brand new 564XL ink cartridge to use in my new 6520.  Message says - HP protected cartridge installed.  Replace Cartridge. 
    I have three more new cartridges from the 6510, color, that likely will have the same problem when I install them.  How can I get them to work in my 6520.

    Hi tsuribaka,
    Welcome to the HP Forums! I understand that you are trying to use the HP 564  XL ink cartridge, from your broken HP Photosmart 6510 with your new HP Photosmart 6520. I am happy to help you with this issue!
    In order to use those old cartridges, you must first use the setup cartridges that came with the new printer, in order for it to initialize. Once you put in those old cartridges the setup cartridges will become unusable. I recommended using up the setup cartridges first, then use the old cartridges that you have.
    Make sure to store the old cartridges, in an air-tight container, such as a zip-lock bag, or a Tupperware container. In a cool, dry place.
    Hope this information helps you, and thank you for posting!
    RnRMusicMan
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to say “Thanks” for helping!

  • HT3500 I have mosx Lion have no driver for my photosmart c4580 printer and the printer test page gives no ip address. How do I get my printer to work?

    We bought a new Mac bookpro using the latest version of lion 10.8. We also have a c4580 photosmart printer and have bee unable to find a driver down load for this printer and our Macbook. We have tried to use u tube and other sites including Apple support to try to connect to our printer. We run a printer test page and the ip address comes up "not applicable". Do we need to connect the macbook to the router? What are we doing wrong? HP site will not give us a driver download. I have to buy it. Seems simplar to goand buy a new printer but this one is still good. Can anyone help? We are not as software savy as alot of you out there. Thanks.

    Download the HP drivers here:
    http://support.apple.com/kb/DL907
    Download the Epson drivers here:
    http://support.apple.com/kb/DL1398

  • Help - Wrieless help for HP Photosmart C4780 Printer / Mac

    I recently moved from California to North Carolina and I am having trouble connecting my HP Photosmart C4780 printer wirelessly to my MAC. I am running OS 10.8. It works through the USB but how do I connect it via wirelessly agian. It worked great in CA, but since moving here and having a new modem/router combo, it is not working.
    I could not find anything so far on this site that has was helpful .
    Software is up to date. just need to know how to make it work wirelessly.
    Thank you.

    You need to connect your printer to you router via your new SSID and password.  Please read your manual for info.
    Replacing your wireless router now try.
    http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
    Say thanks by clicking the Kudos Thumbs Up to the right in the post.
    If my post resolved your problem, please mark it as an Accepted Solution ...
    I worked for HP but now I'm retired!

  • Just bought a season pass to a tv show...but it doesn't work?! Only 30s preview loads??

    Just bought a season pass to "Breaking Bad- Season 1"...but it doesn't work?! Only 30s preview loads??
    I only managed to watch episode 1 and then downloded episode 2, but it only shows 30 seconds of it. Please help!

    Hi Bell_li82,
    Welcome to the Support Communities!
    The articles below may be able to help you with this issue.
    Click on the links to see more details and screenshots. 
    iTunes Store: Download options when purchasing TV seasons, Season Passes, Multi-Passes, movie bundles, music box sets, or individual movies or TV episodes
    http://support.apple.com/kb/HT5731
    Downloading past purchases from the App Store, iBookstore, and iTunes Store
    http://support.apple.com/kb/HT2519
    How to report an issue with your iTunes Store, App Store, Mac App Store, or iBooks Store purchase
    http://support.apple.com/kb/ht1933
    Cheers,
    - Judy

  • OCR for HP Photosmart 6510

    Does anyone know how I can obtain Optical Character Recognition when scanning with an HP Photosmart 6510, please? I have a new PC using Windows 8.1.
    Thanks in advance for any help.

    BusheyBrown,
       Here is a link to a document that might help
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c03478505&lc=en&product=5058336&tmp...
    I was an HP employee
    If I have helped you solve your issue please mark it as solved
    **Say Thanks By Clicking on the Kudos Star**

  • Need Windows 7 driver for HP Photosmart 1115 printer

    I just got a new computer with Windows 7, 64-bit.  My HP photosmart 1115 printer worked great with my old system using Windows XP but I can't get a driver to work now.   The HP site says they don't support it.  Ideas?
    This question was solved.
    View Solution.

    rbaines2 wrote:
    I couldn't find HP 7200 or HP1115  Photosmart - win7 info on that page.
    I followed for a different printer instructions but the Photosmart 7200 driver only lists a manual duplexing option.
    Is there another driver that will work for the HP 1115 that support auto duplex?
    Thanks
    Use the Deskjet 970 or 990 driver as described above and enable the duplexer as described in my previous post.  
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Maybe you are looking for