I bought an airport extreme (5th gen) and have set it up today. However I am having troubles getting it to co-excist with my already set up ethernet connections which are necessary due to the size of the house.

Please let me know how I can set it up so it works along with my ethernet cables and downstairs network. I have several ethernet connections that I need to use as they are out of range of the network.

When trying to connect my AppleTV 3rd gen to another ethernet port of airport extreme with another faster (85mbps) Trendnet ethernet adapter via a different electrical outlet, my extreme goes from green light to flashing amber light and my wifi stops working.
If the Apple TV was originally setup for WiFi, I suggest that you reset the device back to default settings and then configure it again with Ethernet plugged in. Settings > General > Reset > Reset Settings
As a test, connect a spare Ethernet cable of any length (that you know is working) from the LAN <-> port on the AirPort Extreme to the Apple TV for the setup.
Setup the ATV again and double check to make sure that it is operating correctly
Change the location of the ATV back to the desired location on the network behind the powerline adapters
If you have a problem now, the first thing to check is the powerline adapter and or wiring

Similar Messages

Solution: Airport Extreme (5th gen) and Comcast

Recentlty, I had a nightmare trying to install a new Airport Extreme (fifth generation) into a plain jane Comcast-iMac hardwire setup. Applicaton was to provide secure net for video streaming to Xbox and for printing as well as guest network for, uh, guests. After a struggle, I found both the problem and the fix.
Comcast modem direct wire to iMac was solid, but modem to Extreme WAN was no go with either wireless or wired connection between iMac and Extreme. After a few choice words hurled at the obviously incorrect "Ethernet cable not connected" message reported by the Extreme, it finally dawned on me to listen to what I was being told.
If the Airport Extreme couldn't see the cable going from its WAN port to the Comcast modem, then either my cable was bad or the two devices were "failing to communicate." I knew the cable was good (I tried both known good Cat 5E and Cat 6 ones), so it had to be the devices. Then, I remembered they first had to do a little dance (autonegotiation) to decide at which Ethernet speed (10/100/1000Mbs) to talk to each other. I found the settings page that controlled this process and switched it from Autonegotiate to 100Mbs Full Duplex and voila!
Comcast modem was Ubee DDM3513 (standard equipment for Comcast basic hardwire installation).
Hope this helps someone else.

+1
Thanks for the info. This sure helped me out.
I have CableVision Optimum Broadband, and was experiencing the same problems.
Changed from autonegotiate to 100Mbs and boom, internet.
I wonder if it will be faster work with 1000Mbs...

Multiple WPA2 passwords on Airport Extreme (5th Gen)?

I have just purchased an Airport Extreme (5th Gen) and would like to set up each radio with a different WPA2 password. Is this possible?

Unfortunately, Apple does not provide this option.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Airport Extreme 5th gen overheating

Lately we've had some very hot weather, and my AirPort Extreme (5th gen) has been dropping out in a weird way.
It drops all connections, the other connected AirPorts flash orange, but the Extreme just sits there with a green light like nothing is wrong.
Only unplugging and plugging in again fixes it. When this happens, it feels quite warm on the top, which makes me think it might be overheating.
Setup is basically AirPort Extreme handling PPPoE login bridged to a DSL modem, two AirPort Expresses wirelessly extending and bridging the network to Ethernet, no direct Ethernet connections on the Extreme. Latest firmware.
Worth taking it to the Apple store? Bought it in August 2012.

Well it is out of warranty unless you have applecare on a computer or ATV, that is current.
I would say the latest firmware is fairly bad for this setup.
Return it and the express units (I know less about them) to 7.6.1 firmware and do a factory reset and start over.
Ignore any future request for upgrade of firmware.
What airport utility are you running?
Downgrade is very easy from v6.. hold in option key and click the existing version number.. and a selection of firmware will be presented dependent on the model.
In very hot weather.. Like 4 days of over 40deg we just had in Melbourne.. you would find the top of the TC 15deg above ambient.. it is pretty hot.. more than 20 is serious.

Can't print from iPad to HP via Airport Extreme (5th gen)

I have an HP Deskjet 5900 connected to an Airport Extreme (5th gen), via the USB port. I'm currently running 10.6.8 and have succesfully setup the printer such that I can print wirelessly from my MacBooks, as well as directly from my MacPro desktop (which is connected to the AEB through the network).
What I can't do is AirPrint from my iPad or iPhone.
I've skimmed through quite a few questions on here, but haven't come across this specific scenerio. The closest one refers to printers that are AirPrint compatible, but I believe that only applies to wireless printers that are being connected on their own (without an AEB).
I really hope I don't have to download an app for this... it's built right into the iOS!
Thanks for the help.
Stephen

To use AirPrint directly from your iPad, you will need a printer that is AirPrint-compatible. Currently, the HP Deskjet 9500 is not one of them. There a few workarounds, but they will require obtaining an App.

I will have an AirPort Extreme 5th gen in a few days.....

I will have an AirPort Extreme 5th gen in a few days. I have an older model and when playing with settings, I found out that my Epson wireless printer can only see 2.4 ghz 802.11n networks.....
but I want to use the 5Ghz wireless.....is there anyway to bridge the 2 networks or connect to both for AirPrint's sake?
Any suggestions?

but I want to use the 5Ghz wireless.....is there anyway to bridge the 2 networks or connect to both for AirPrint's sake?
If the printer can only support the 2.4 GHz radio band then, even if you could bridge the two (not possible), the printer would still not be able to connect ... and this is true for any wireless client whether it is a printer, computer, etc.
Wireless clients that support both bands can connect to one or the other typically based on received signal strength. They don't connect to both simultaneously.

Is the original iPad capable of configuring the airport extreme 5th gen?

How to set up hdd with airport extreme with iPad?

Is the original iPad capable of configuring the AirPort Extreme 5th Gen?
Yes, using AirPort Utility for the iPad.
AirPort Utility for iPhone, iPod touch, and iPad on the iTunes App Store
How to set up hdd with airport exreme with iPad
You do not set up a hard drive with the iPad, you set up a hard drive using Disk Utility on your Mac. Make sure that the hard drive is formatted in Mac OS Extended (Journaled) before you connect it to the USB port on the AirPort Extreme.
If you want to access data on the hard drive from the iPad, you will need an App like Filebrowser.
FileBrowser - Access files on remote computers for iPhone, iPod ...

Airport Extreme (5th gen) Buzzing / Hissing

I have a 5th generation airport extreme that I am using with Sky fibre broadband in the UK. It is working fine I am however experiencing an issue that I have never seen with a router before which is that it making a hissing or buzzing sound under certain conditions.
It is not really loud and I have to be pretty close to hear it, I have not done any extensive testing however it seems to only be happening when connected to my Macbook Pro over 5GHZ wifi and some activity such as copying a file is taking place. I have owned an airport extreme (5th gen too) previously and never noticed this then although I could have just missed it.
I have found similar cases searching online but these mostly seem to indicate that they had the router replaced only to experience the same thing on the replacement! I have a genius appointment at the weekend but as I live a fair way from the store I’d rather not go in if this turns out to be normal behaviour, especially as it is (at the moment) really not that loud. Likewise however any kind of hissing or fizzing from a router just does not seem right to me and I’d also worry that it could maybe get worse.
Anybody else experienced this?

An Extreme should be completely silent but a buzzing or sizzling noise can emanate from components in its power supply. It may change depending on the Extreme's power demands; a function of your wireless environment.
If it were new I'd want to exchange it for another because the noise can be annoying, but if it's out of warranty I wouldn't be concerned. It does not necessarily indicate an impending failure.

Usb hard drive connected to AirPort Extreme 5th gen not detectable

hello
I connected a exFAT formatted HD via USB to my AirPort Extreme 5th gen.
I'd like to have access to it via my iMac as well as my gf's win laptop.
I only can se the drive in Airport utility but am not able to use it (copy files, read files I put on directly connected to my iMac).
so what could I do?
thank you in advance!
cheers Chris

Thank you!
That was a great hint. I can now access the external HD via my iMac.
on the other hand I'm no longer able to go online with my gf's win laptop.
there's no way to get an internet connection working.
I can see the wlan of the airport extreme but I am not able to log in...
I have no glue!
any help is highly appreciated.

I have an airport extreme base station and have no clue how to set up a private wireless network instead ton open one i have now.

I have an airport extreme base station and have no clue how to change to a pawword type network from the network i have now that is free to the neighbor hood.

Which version of the AirPort Utility are you using?

HT1373 I bought an ipod nano 5th gen and it came with 900 songs on it. How can i retain the music before i authorize this unit to my itunes account? It says it will erase all content once I sync with my imac7. Is there anyway to keep the music??? please h

I bought a used ipod nano 5th gen and it came with 900 songs on it. How can i transfer, sync, and retain the music before i authorize this unit to my itunes account? It says it will erase all content once I sync with my imac7. Is there anyway to keep the music??? please help!!
Thanks,
Aaron

The music does not belong to you. You have no legal right to it and there is no way to keep it.
Sorry

AirPort Extreme (5th Gen) WiFi access point disappears but wired ethernet is ok

My AirPort Extreme SSID and access point "disappear" randomly from available WiFi networks. I had a 1st gen AirPort Extreme and never had this problem until earlier this year. I thought it might be a failing radio in the 1st gen unit so I used it as a good excuse to get a 5th gen AirPort extreme about 3 months ago. Same problem has been occuring; unfortunately it is random and I cannot get a handle on what/when/why it is happening.
For example, my iPhone 4S was connected to the network at about 1700 today and when I next checked the phone around 2115, no wifi connection and my network was not listed in the WiFi connections. The base station is away from other wireless devices (mouse, keyboard) and is about 10 feet from the nearest PC and monitor. Both printers are accessed via ethernet, not wifi. The strange and puzzling thing is that the PC, which is connected by ethernet to the AirPort Extreme, is still connected to the internet (I can browse, check email, newsgroups, etc.).
When I run the AirPort Utility, the base station is identified (AirPort Extreme 802.11n 5th Generation), there is an appropriate IP address, Version 7.6 firmware, and MAC address is listed. However, when I attempt to Continue or do a Manual Setup, I'm prompted for the admin password, the progress bar moves during 'reading from the Apple wireless device. Please wait...,' and then the utility reports "An error occured while tryong to access the Apple wireless device. Make sure your network connection is valid and try again. Error -6722.
If I unplug, wait, and reattach the power to the base station, WiFi becomes available again. When the WiFi connection "disappears", the LED light is solid green.
Any insights are appreciated; please let me know other helpful information I can provide.
Scott

I have the exact same problem and it's driving me nuts.
I bought an airport extreme n last week and plugged it in, hooked it up to my adsl router by Ethernet, configured it to set up a new wifi network and got the green light. I use an iPhone 4, iPad 2, and Windows 7 PC with an N wifi adaptor.
The airport works fine for about 2 hours before the wireless network disappears without a trace. Green light remains on the base station and I can connect fine by Ethernet.
"it just don't make sense"
I hope it's not a windows-7-only thing, Apple.
PS. Updated firmware to the newest version, no difference.
Airport is near to a wireless phone so I set a specific wireless channel and frequency to prevent a clash. No change.

I bought an iPod touch 5th gen and its stuck on the find my iPhone screen and i do not have the password! How do i reset it to my account?

Plz help

Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.

Extend my wired Airport Extreme (5th Gen) with a 2nd Wired Airport Extreme (also 5th Gen)

I have a 5th Generation Airport Extreme in my house hard wired directly from my fiber optic provider
Then I have that 5th Generation Airport Extreme hard wired directly to my Desktop Computer in a separate building in my back yard (using an Ethernet Cable run through an underground conduit).
Using that setup, I DO get Wi-Fi for my iPhone 4S & iPad 3 in that separate building in my back yard, but it is sometimes so weak, it really is not useable.
To improve the Wi-Fi signal for my iPhone 4S & iPad 3, I plan on adding a 2nd 5th Generation Airport Extreme in the separate building in my back yard.
I will disconnect the Ethernet Cable that is currently plugged directly into my Desktop computer & plug it into the 2nd Airport Extreme.
Then, I will use a short Ethernet Cable to directly connect my Desktop Computer to the 2nd Airport Extreme.
The desktop computer is an older Dell Dimension 9200 running Windows XP Professional with Service Pack 3
With this set-up, will the strong Wi-Fi signal I now get in my house from the 1st Airport Extreme NOT be reduced?
And since the separate building is only 300 square feet, I assume the Wi-Fi signal there will also be as strong with the 2nd Airport Extreme being so close to everything?
Could someone point me to SPECIFIC instructions on how to CORRECTLY set this up so that the 2nd Airport Extreme will EXTEND my home network?

So, I should unplug the 1st Airport Extreme from the outlet before doing anything?
Yes.
Since the 2 Airport Extremes will be in 2 separate locations, which do I plug into the outlet first?
I would suggest plugging the one in the house first, then the second one in the backyard building. Be sure to connect the Ethernet coming from the first into the second before power-on either base station.
Could I connect the Ethernet both to the 2nd Airport Extreme & then to the desktop, then plug in the current Airport Extreme in the house, then run out & plug in the 2nd Airport Extreme in the separate building?
The key is to leave everything powered-off; connect the Ethernet cables, and then, start by powering up the house unit, then the backyard unit, and then, the PC. Make sense?
P.S. I have the Version 5.5.3 of Airport Utility for Windows (using Windows XP Professional with Service Pack 3)
There does NOT seem to be a later version than that.
That worked great for the installation of the 1st Airport Extreme several months ago, so I shouldn't have any problems, should I?
There is a later version (5.6.1) for Windows, but required Windows 7 to run on. Since you can already administer the 1st 5th gen Extreme with the version you have now, you shouldn't have any issues continuing to use it for the second unit.

I bought an airport extreme (5th gen) and have set it up today. However I am having troubles getting it to co-excist with my already set up ethernet connections which are necessary due to the size of the house.

Similar Messages

Maybe you are looking for