I bought CS6 and got the Serial Number, but when I install, it said cannot verify this number, I need help!

I bought CS6 and got the Serial Number, but when I install, it said cannot verify this number, I need help!

Contact Adobe (You may need the chat option):
Contact Customer Care

Similar Messages

  • I have just bought and installed adobe acrobat pro and got the serial number too, why do you ask for

    I have just bought and installed adobe acroba
    t pro and got the serial number, but now the system k
    eep asking me for an old serial number from my former version.
    During the years I have reached vesion 9, but I don't have any old serial number.
    What to be done?

    you got a discount because you bought an upgrade version. it needs proof that you own a previous version. more info can be had if you post in the correct acrobat forum. this forum is for questions and comments about the workings (or not as the case may be) of the forums themselves.
    http://forums.adobe.com/community/acrobat

  • I bought Studio MX in 2006. I have the CD and the serial Num. but when I tried to reinstall it, it would not recognize the serial number. I registered the product in 06. Back then it was called macromedia.

    I bought Studio MX in 2006. I have the CD and the serial Num. but when I tried to reinstall it, it would not recognize the serial number. I registered the product in 06. Back then it was called macromedia. 

    MX 2006 is so old it's no longer supported.  See if this helps you.
    Error: Unable to Activate | Macromedia products
    Nancy O.

  • My problem started when system preferences was unresponsive and would not force quit.  I tryed to restart and got the grey screen, but it never restarted.  I closed the lid and now the screen is blank.  Has anyone had a similar problem after Lion?

    My problem started when system preferences was unresponsive and would not force quit.  I tryed to restart and got the grey screen, but it never restarted.  I closed the lid and now the screen is blank.  Has anyone had a similar problem after Lion installation?

    No, as I have yet to be convinced on Lion.
    Did a permissions repair help from the install DVD?

  • HT204370 OK i bought a movie got the confirmation email but iTunes says I need to buy it even the funds where taken

    OK i bought a movie got the confirmation email but iTunes says I need to buy it even the funds where taken

    Not sure what your issue is or what your question is.

  • I got a new computer and i cant get my music on my phone from iTunes. i got an mp3 file and got it on itunes but when i try to get on my phone nothing happenes. my family have helped me but nothing is working. i don't want to delete anything

    i got an mp3 file and got it on itunes but when i try to get on my phone nothing happenes. my family have helped me but nothing is working. i don't want to delete anything. DONT KNOW WHAT TO DO!!!!!!!!!!!!!

    Yes but all your previous content from the old computer will be erased.
    Read this:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive

  • I delete people in my phone number but when I go to messages I found their number and name how I can delete them

    I delete people in my phone number but when I go to messages I found their number and name how I can delete them

    There's no option to edit/delete the iPhone cache, the cache will be overwritten in time.
    If you can't wait, only restore as new can get rid of it.

  • I just bought a song on the iTunes store, but when it reaches about one minute, it just skips to the next song. What should i do?

    I just bought a song on the iTunes store, but when it reaches about one minute, it just skips to the next song, with no warnings. I tried to delete and download it again, but it didn`t solve the problem. What should I do?

    Restart your Mac and try again...
    If no joy...  Contact iTunes Customer Service
    Apple  Support  iTunes Store  Contact Us

  • I am able to get color images in the continues shot but when i try to snap a color image which i need for my processing i get only a monocrome image

    I have been using lv_vfw.llb VI's for grabbing images from a CREATIVE WEB CAM ,i am able to get color images in the continues shot but when i try to snap a color image which i need for my processing i get only a monocrome image ,i have been trying to play around with the RGB weightings but i am unable to get a color iamge,it shall be of great help if you could help me in doing this as it is urgent for me.Thanks for your help.

    vicky,
    I am unfamiliar with the lv_vfw.llb, and have not used it before. However, I noticed that you stated that you are able to grab in color, just not snap in color. If this is the case, why not just perform a grab and then extract a single buffer from this grabbed data, which would likely be in color? This seems like a possible solution to the issue that you are seeing.
    Other than that, I really don't know enough about the lv_vfw.llb to be of much help on this issue. Hopefully another member of this forum will be able to assist you with this software.
    Regards,
    Jed R.
    Applications Engineer
    National Instruments

  • I recently did a restore to factory settings on my 2009 macbook and now im stuck on the welcome screen where u choose the country my trackpad allows me to move the arrow around but when i tap continue to choose it does nothing. someone please help

    I recently restored my 2009 macbook to factory settings and now its stuck on the welcome screen where u choose your country. My trackpad allows me to move the arrow around but when I tap on it to select continue it does nothing at all. The only thing else it will allow me to do is go thru the voice over tutorial by pressing escape. Please help me fix this I need to use my computer.

    Hi, teezbreezy64.
    I found a couple of resources to help troubleshoot the issue you are experiencing. The first is this article named Intel-based Mac notebooks: Troubleshooting unresponsive trackpad issues found here http://support.apple.com/kb/TS1248.
    Try disconnecting the MagSafe connector from the computer and check the trackpad function. If the trackpad becomes responsive again, improper grounding may be the issue.
    If a two-prong AC plug is being used with the power adapter, try using the three-prong power cable that shipped with your computer and plug it into a grounded outlet.
    If the issue persists, make sure the third prong is present and do not use an adapter to enable the three-prong adapter to be used in a two-prong outlet. Note that the ground in the three-prong outlet may not be connected. This is common in older homes or buildings with replaced outlets. In these situations, the three-prong power cable will not improve trackpad responsiveness.
    If a grounded outlet is not available, rest your palm on the palm rest when using the trackpad. This should enable the trackpad to function properly.
    If that does not resolve the issue then I recommend resetting the SMC on your computer. Here is an article on how to do that:
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/ht3964
    Regards,
    Jason H. 

  • HT1937 I have already unlock iphone4 from the apple website but when I install SIM card than no service display

    My brother send iPhone from USA to India
    iPhone 4 already unlocked from the apple website
    Not  using jailbreak system
    But when I install SIM card it displays no service
    What I have to do for this solution

    Gauravpatel00045 wrote:
    My brother send iPhone from USA to India
    iPhone 4 already unlocked from the apple website
    ONLY the Carrier that the Phone is locked to can Unlock it.
    Gauravpatel00045 wrote:
    ... when I install SIM card it displays no service
    What I have to do for this solution
    Please see the More Like This section on the right.

  • TS1567 Tried installing itunes and got the message "Service 'Apple Mobile Device' failed to start. Verify that you have sufficient privileges to start system services".

    I did as Apple suggested and went into my services page and stopped the Apple Mobile Device service. Once it stopped I started it again. I then went through the downloading of iTunes process again, and I got the same error. I have McAfee and Webroot Security, and I am operating on Windows 7. What should I do?

    So many people are having this problem! Doehunter's instructions here worked for me!  Hope this helps. https://discussions.apple.com/message/23824640#23824640

  • I bought and paied the Creative Cloud but when I open Photoshop appears the message: "continue the trial". Why?

    I bought and paied the Creative Cloud (€19 por month) but when I open Photoshop appears the message: "continue the trial". Why?

    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • Sold Feb 2008 MacBook to someone. I had Lion and had the drive erased, but now it's asking him to reinstall in disk utility. HELP!

    So, I had a friend who is a computer expert erase my computer before I sold it to someone. I had Lion so advertised the laptop as running Lion. It's a Feb 2008 model Macbook.
    He has since received it and says it is opening in disk utility asking for a username and password to install Lion. Please help! I'm not the best with computers, and unfortunately I am a student and can't afford much to fix this. I also can't find the original disks that came with the computer.
    Thanks!                             

    Your friend didn't erase the hard drive completely so the mac is starting Into the recovery partition. The buyer needs the original discs, if he calls 1-800-MY-APPLE and provides them with the serial number they can ship him a set of original discs for a small fee. He needs to start up with disc one in by holding the C key and then through Disk Uility delete the revovery partition and reinstall the software. If he wants to upgrade to Lion he'll have to purchase that on his own.

  • I got the Blue Screen-But Not After Installing Leopard

    I have not installed anything recently. Except Quake 4 but haven't even run it yet. I Rebuilt my Permissions and Restarted and suddenly got the Blue Screen. I had to hold down the power button and reboot. This is the first time it's ever happened. After I rebooted I got an error message saying OSX shut down unexpectedly. It also said this:
    Sun Feb 24 10:46:29 2008
    panic(cpu 0 caller 0x0019D334): "simple lock deadlock detection: lock=0xd8428b0, cpu=0, owning thread=0xe2376b0"@/SourceCache/xnu/xnu-1228.3.13/osfmk/i386/locks_i386.c:317
    Backtrace, Format - Frame : Return Address (4 potential args on stack)
    0x108cd8 : 0x12b0e1 (0x457024 0x108d0c 0x13321a 0x0)
    0x108d28 : 0x19d334 (0x45eaa8 0xd8428b0 0x0 0xe2376b0)
    0x108d48 : 0x7c0fff21 (0xd8428b0 0x8 0x1 0x19d311)
    0x108da8 : 0x1aeeeb (0x7c1f10a4 0x5328a4 0x2ae14865 0xd9dbd60)
    0x108dc8 : 0x136aff (0x3 0x5 0x108e18 0x5baa44)
    0x108de8 : 0x141681 (0xd9dbd60 0x0 0x108e18 0x41d16e)
    0x108e18 : 0x41d774 (0x5baa40 0xd96bc5c 0x0 0x1298d4)
    0x108e38 : 0x836b6ebf (0xd96bc40 0x2 0x108e88 0x1415aa)
    0x108e98 : 0x836b6f1a (0xd933000 0x0 0x1 0x8358d000)
    0x108eb8 : 0x420af3 (0xd933000 0xda98c80 0x10 0x1997f6)
    0x108ef8 : 0x435cbb (0xda98c80 0x0 0xd980f80 0x0)
    0x108f28 : 0x82d9e521 (0xdab8880 0x0 0xdab8880 0x0)
    0x108f58 : 0x7bee5777 (0xd7fb000 0x0 0xd8de500 0x53)
    0x108f78 : 0x7bedec41 (0xd7d2a00 0x0 0xd8de500 0x53)
    0x108f98 : 0x445d88 (0xd8ec400 0x0 0xd915b00 0x53)
    0x108fd8 : 0x19ed2e (0x83dd3db0 0x0 0x0 0x4e5000)
    Backtrace continues...
    Kernel loadable modules in backtrace (with dependencies):
    com.apple.driver.AppleUSBEHCI(3.0.7)@0x836b3000->0x836c4fff
    dependency: com.apple.iokit.IOUSBFamily(3.0.8)@0x8339b000
    dependency: com.apple.iokit.IOPCIFamily(2.4.1)@0x7be78000
    com.apple.driver.AppleAPIC(1.2.0)@0x82d9d000->0x82d9ffff
    com.apple.driver.AppleIntelCPUPowerManagement(9.33.0)@0x7c0fe000->0x7c116fff
    com.apple.driver.AppleACPIPlatform(1.2.1)@0x7bedd000->0x7bf19fff
    dependency: com.apple.iokit.IOPCIFamily(2.4.1)@0x7be78000
    dependency: com.apple.iokit.IOACPIFamily(1.2.0)@0x7be8e000
    BSD process name corresponding to current thread: kernel_task
    Mac OS version:
    9C31
    Kernel version:
    Darwin Kernel Version 9.2.0: Tue Feb 5 16:13:22 PST 2008; root:xnu-1228.3.13~1/RELEASE_I386
    System model name: MacPro1,1 (Mac-F4208DC8)
    --Does anyone know what this means or why it happened? Thanks a lot.

    Start with http://support.apple.com/kb/TS1541 and the links therein.

Maybe you are looking for