I bought nano 7th generation and docking station adapter, now nano reads Unsupported Acccessory is not supported" and nano will not operate in IPOD docking station??
My ipod nano 7th generation requires a docking adapter which I bought however when connected to docking station a message appears "unsupported accessory is not supported" how do I correct this so it will play?
If it is a lightning to 30 pin adaptor, and you have a 7th Generation Nano it has to fit the Nano.
This is lightning to 30 pin adapter: http://www.bestbuy.com/site/Apple%26%23174%3B---Lightning-to-30-Pin-Adapter/6651 936.p?id=1218803450821&skuId=6651936#tab=overview
Is this what you bought?
You need to contact Sony and see if they model you have is compatible with the docking adapter. It may not be.
Similar Messages
-
How do I get the ipod nano 7th generation to only show the album artwork? the volume control, info bar and album artwork shows whenever a song is playing.
Hi TheGuru146,
It sounds like the iPod isn't restoring correctly. Try putting the it into Disk Mode manually and then restoring the iPod again as described in the article linked below.
Putting iPod into Disk Mode
http://support.apple.com/kb/ht1363
iPod nano (7th generation)
Before placing the iPod into Disk Mode, verify that it has a charge.
Reset the device by pressing the Sleep and Home buttons simultaneously until the display shows the Apple logo. This should take about eight seconds.
When the Apple logo appears, press and hold the Volume Down and Volume Up buttons simultaneously until the device enters Disk Mode.
-Jason -
It doesn't say so on the box, just the ipod nano 6th and earlier. I am hoping someone already tried using the 7th and has an answer.
Hello Jay,
Welcome to the Sony Community.
The Sony RDH-GTK33iP Home Audio Docking System is not compatible with iPod Nano 7th generation.
Thank you for your post. -
How can i load the device driver for my ipod nano 7th generation
When I plug in my ipod nano 7th generation (for the first time), I am getting a message about "unknown device" and "driver not installed properly". Can I manually load the device driver some other way?
Hi there Jen292,
You may find the troubleshooting steps in the article below helpful.
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
-Griff W. -
I have a new Ipod Nano 7th Generation. When I plug the earphones in, there is no sound coming from the earphones, even thought the Ipod shows the song as playing. Any solutions?
And the Radio app probably doesn't work either.
The headphone jack on the nano is very tight when new. Push the jack all the way in, the plastic on the headset jack should be flush with the body of the nano. -
How to use search function in ipod nano 7th generation
how to use search function in ipod nano 7th generation?
Cheers thanks.There is no search function. If there was, it would be mentioned in the iPod's User Guide.
7G Nano User Guide
B-rock -
HT201570 Looking for a MSDS for a Ipod Nano 7th generation can anybody help?
Looking for a MSDS for a Ipod Nano 7th generation can anybody help?
Here, at the end of the site, you can find some environment specs from ipod nano 7th generation... hope this few informations could help you
http://www.apple.com/ipod-nano/specs.html -
my ipod nano 7th generation....works fine as long as it's on the docking station. when off the station, the display goes dark after a few seconds. it's fully charged. please help. this is the heartbeat of my business. thanks
In the worst case, it's still under warranty (all 7th gen nanos are still under one year from purchase).
So, you disconnect it from power, and it almost immediately goes dead? You can try a Restore... but it doesn't sound like the type of problem a Restore will fix.
You should probably have it looked by Apple Tech Support. If there's an Apple Store nearby, you can take it to the store's Genius Bar. To avoid waiting, you can make a reservation at the store's web page
http://www.apple.com/retail/ -
Just bought an IPod nano 7th generation. I have a Mac computer OS X v10.5.8 with 10.6.7 iTunes player. To use the new IPod nano I need a OS X v10.6.8 or later and iTunes 10.7 or later. What are my options to upgrade the Mac?
Thanks to your feedback.Click here, check that your computer meets the requirements, purchase and install the DVD, and run Software Update.
(74380) -
I bought the i-pod nano 7th generation. But it has a new connecting cable. How do I connect it to my audio dock player which has the wide pin dock?
you will need to buy a lightning to 30 pin adapter
http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter -
Can the i pod Nano 7th Generation be connected to a Bose docking system?
Can the i pod Nano 7th Generation be connected to a Bose docking system? Or is there some other docking system that can be used? I need to play my i-pod Nano over a loudspeaker system of some kind.
In order to connect the 7G Nano with older accessories, you'll need the Lightning to 30-pin adapter.
http://store.apple.com/us/product/MD823ZM/A/lightning-to-30-pin-adapter
As for a clip, you'll have to wait and see if any third party manufacturer's release a case/cover/sleeve that includes a clip.
B-rock -
My iPod Nano 7th Generation couldn't be detected by iTunes when I plugged in. I tried resolving the issue by uninstalling the iTunes and then install it back again but yet still the same problem exist. Can you please help me to solve this issue? I have already updated to the latest version of iTunes on my Windows 8 and I cannot synchronize my iPod for the time being. Please do help me to solve this problem. Thank You.
uninstall all iTunes,5 programes,this worked for me after reinstall them
-
I recently purchased the new nano (7th generation) and I love it except for one issue. On my old 2nd generation nano, when I played podcasts, it would play podcasts one at a time. So if I had 20 episodes of a podcast on the device, it would stop at the end of each one.
With the new nano, I can select and play a podcast, but when it’s over, it goes straight to the next one without prompting. It keeps on playing all of the episodes of any podcast until you stop it manually. Setting the repeat function differently does not prevent episodes from being played automatically.
This can be very irritating when I only want to listen to one podcast. I’ve often fallen asleep listening to one episode of a podcast, only to be woken up hours later by the iPod working its way through all subsequent episodes. It is also annoying that any podcast which has started automatically in this way is marked as ‘played’ – even if you stop it within a few seconds. This makes it hard to keep track of what you have actually listened to.
Is there any way to set the iPod to play all the podcasts individually? I have read the User Guide from cover to cover, and can’t find a way of doing this.
MDDude or hot-spur,
Not fishy at all!!!! You really think I would have taken any more of my time to post a bogus rant? We'll no, it is unfortunately all true. I want to hear from anyone who is experiencing such problems not anyone else that wants to put there two cents in. I really don't need anymore hate or negativity. Just people's experiences because I feel like I am the only one having so many problems. Thank you
Yes, I have had some unfortunate bad luck to have so many problems at the same time, but some of them are just things you cannot do on the new OS.
Thank you again -
I have an ipod nano 7th generation and can not get it recognised by my Windows 8.1 laptop (it appears briefly on My computer, then disappears). This happened after I updated iTunes to the latest version. Does that have something to do with it?
Hello there, kiwilucea.
The following Knowledge Base article offers up some in-depth steps for troubleshooting your issue:
iPod not recognized in My Computer and in iTunes for Windows
http://support.apple.com/kb/ts1369
Keep in mind if you get to Step 12 Reinstall iTunes, those steps need to be followed exactly as outlined for the reinstall to be effective.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
For some reason my IPod nano 7th generation is not recognized by ITunes. It has recognized it up until today. I have followed every step that is provided for troubleshooting and nothing is working. Does anyone have any suggestions?
Hello sipsy12,
Thanks for using Apple Support Communities.
For more information, take a look at:
iPod nano not appearing in iTunes
http://www.apple.com/support/ipodnano/assistant/itunes/
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/TS1363
Have a nice day,
Mario
Maybe you are looking for
-
[SOLVED] Problem with Kate and his dependencies
hi, I just read the post which explains how to install kate from other packages of kde. http://bbs.archlinux.org/viewtopic.php?id=51748 I've done what we said last answer, but my problem is that when I try to install kdesdmod with its dependencies, t
-
Errors Installing on Windows Vista
It looked like Flex Builder 3 installed correctly on my new Windows Vista machine, but then I go to run the program (Adobe Flex Builder 3) as an administrator, see the black splash screen come up, but then receive the following message: FlexBuilder [
-
Transfer my OS to a larger drive
I have a mac pro 8 core and need to upgrade my hard drive to a 1TB. I know how to format it. I can also add ML, but I want to bring everything over from my 640TB Drive. Without a firewire cable (I dont' have an external housing) if I insert the drive
-
Adobe E-mail Service doesn't work
I'm trying to send ONE photo to a friend. The HTML Email dialog box appears requesting verification. Is this really necessary? Anyway, I'm supposed to receive an email with a "Sender Verification" number. I never get an email. I press "Resend e-
-
Odd behaviour with parameter id on selection screen
Try this code PARAMETERS: p_fpath1 TYPE string LOWER CASE MEMORY ID rofile, p_fpath2 TYPE string LOWER CASE. AT SELECTION-SCREEN ON VALUE-REQUEST FOR p_fpath1. PERFORM get_filepath CHANGING p_fpath1. AT SELECTION-SCREEN ON VALUE-REQUEST