I bought printer with that recognizes my wireless router it is hook up to my pc, how can i get my mac and i pad to print to to, i bought printer with that recognizes my wireless router it is hook up to my pc, how can i get my mac and i pad to print to to
i bought a printer with wireless capabilities, i have it recongnizing my router and it is loaded to my pc. how can i get the printer to recongnize my mac book and ipad. all my apple prouducts use my router.
While uselessSABOTAGE's advice is great, in case of future issues, it would helps us in the future if you would post accurate tech specs of your model iMac.
You info states you have an older IMac PowerMac, but is also says your OS X version is OS X 10.7.2.
This is not possible. OS X 10.7.2 Lion only runs on Intel CPU Macs.
Please, go up to the Apple symbol in the upper top left of OS X main menu bar. Click the symbol. Then click About this Mac. A popup window appears that gives some basic info. Then, click the More Info button and both post your iMacs complete specs by selecting/highlighting all of the info and copy paste this into a reply to this post, editing out your iMac's serial number. Then update the info you posted in your user profile with some of this new found data for future postings.
Similar Messages
-
I don't have a wireless printer, and want to print things off of my iPad. I know that I can use the iPad Camera Connection kit to connect USB devices like keyboards and I am wondering if I could do the same with a USB printer.
I don't think you can connect a printer since you won't have the printer drivers. I use FingerPrint from collobos.com to print to my non-AirPrint printers.
-
I have a Mac connected to Internet via DSL modem. Just bought an iPad2 and need to know what hardware do I need to add wireless LAN so I can use iPad anywhere in the house. Will a Linksys router work with Apple? Can Mac be "hardwired" and iPad wireless? Probably stupid questions but I need to learn. Thanks.
Bob Timmons wrote:
Thanks for the info. You are correct. I was speaking in general terms here based on my experience with the two devices in day to day use, and not in terms of exact specifications.
A better choice would have been to say that the "coverage" is about the same with the edge going to the Extreme....due to the newer mutliple antenna design.
We sure could use more help on the forums. Hope that you will become a regular.
Hi Bob
RF is a minefield, but one that I have worked in for ages, the most critical factor in my experience is location, location, location!
Better routers have more intelligently designed antenna systems, output power as I said is the same, radiation pattern (coverage) is dependent on antennas and physical location more than all other factors. -
I am a Canadian staying in England for a few weeks. How can I get an iPhoto Book printed win England and sent as a gift to an English relative? With my account, it seems that Apple only allows for my book to be printed in Canada and then sent to my Canadian address..
in the iPhoto preferences change the print products country to the UK and give it a try - there may be some restirctions on billing but it has worked for some people
LN -
I have repeatedly installed and uninstalled Microsoft Silverlight, I have followed every thing out there and uninstalled from various folders. It still states the program is there and it won't run. This is also happening with my coupon printer that word
Copied from a page that helped me:
I followed someone else's advice and found all the silverlight files in "INVISIBLE FILES".
In the Finder, choose File > Find or press Command (⌘)-F.
From the far-left pop-up menu (labeled “Kind”), choose Other.
In the list of search attributes, select the “File invisible” checkbox, and then click OK.
In the related menu, choose Invisible Items.
once loaded go to folder Private
then to folder VAR
then folder db
then folder Receipts
scroll to any com.microsoft.silverlight item and delete. there are a bunch of them.
close, restart and install silverlight. -
Does anyone know what's wrong with it? not booting up. instead of it a picture of a file appears with a question mark on it in the middle of screen?
Sounds like abad hard drive. The clicking sound is coming from the HD. The folder with the question mark means that your computer can't find the statrup disk or the hard drive.
Boot your computer using the install disc and check if Disk Utility can recognize your HD. If not, then it needs HD replacement. If you have AppleCare or within the 1 year warranty, then replacement should be free from Apple. Check the nearest Apple Store in your area. -
Hey
I don't know if my mac book air is frozen, but the screen is gray with the apple logo in the middle of the gray screen, with the 'booting' icon turning round and round. I have switched it off fron both the power and power button on the computer, it goes off, when I put it on, same screen comes on again. Help Please!Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 3
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 4
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 5
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 6
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 6.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 7
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 8
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 9
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 10
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a boot failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 11
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
In Safari, my iMac sometimes zooms way too much and will not zoom back. I have a wireless mouse set to zoom in and out on double tap, but the excessive zooms happen with no taps. A page zooms in so less than 1/4 of the page is visible and nothing I do will zoom back out, command minus doesn't do it, double tap on mouse does not zoom out, and the window will not scroll to show any of the rest of the page. reloading the page does not help. Loading a different page gives me a normal view again.
If it were a tweaked setting, it should happen less randomly. And there should be no settings that could override the zoom setting in unversal Access and the Mouse zoom preferences.
In addition, this only happens in Safari 6, and seems to happen more fredquently on some websites and not on others. That suggests some sort of conflict in the site code with Safari and Apple wireless mouse code. It does not happen in Mail, Word, Excel, Photoshop, Illustrator, or other software as far as I can tell. -
I am trying to set up my apple tv using the hospital network. I am able to detect the network and chose it. But the way the system works is that you have to agree to the terms and conditions of using their network before access the internet. How do I accomplish this with apple? Please help.
There are some other options to you, if you're not at home and nobody is using your router you could set it up at the hospital, if this isn't an option you could get a second router and use it. Many ethernet routers are available on the cheap, and ethernet cables are cheap too.
Also, a macbook can share it's internet via the built in wifi it has. See this go to settings-sharing-internet sharing and configure as desired. This may require an internet connection via ethernet. But you should be able to create a wifi network for using something like airplay/home sharing. -
Hi, I've got an imac using mac os x version10.4.11, does anyone know of any printers that are compatible with this operating system version?
Yesterday I set up a Canon IP3600 to work on a PowerBook G4 running OS 10.4.11. It is a print-only unit. I got the 10.4 drivers off the Canon website before connecting the printer. Many Brother printers still have support for older Mac OS versions.
If you need a multi-function device, it is gettng very hard to find any that support PowerPC Macs (pre-2006) of OSX versions older then 10.6 any more.
As you posted in the PowerPC iMac forum I assume you have one. However, there are some Intel Macs (2006 and newer) still running 10.4. Check "About this Mac" under your Apple menu: if it says you have an Intel processor, you have many more doors open. -
How can I access my apps? They are all greyed out in itunes. I have tried restoring my iphone to factory settings but that didn't work. I have a feeling it may have something to with the restrictions settings on my phone restrictions are on) but it won't allow me to change the restrictions without putting in a passcode. I don't remember ever having a passcode and after several attempts have not been able to get the right code.
Also. on my phone, in settings, personal hotspot, iCloud and Twitter are greyed out. And, the App Store icon is missing from my screen as well.
Can anybody help me with this?
Thanksyep, unfortunately can't reset without the passcode either.
With regards to doing a restore, do you mean:
open itunes on my computer
click on my device on the left
go to the device summary
click restore
it then asks if i want to back up before i restore (to which i say no)
then it asks me if i'm sure I want to restore to factory settings and that all of me media and data will be erased and replaced with the newest version ( to which I say yes)
then it takes about 90 mins to do this but when I look at my phone, everything is exactly the same.
Am I missing something? Obviously I'm technologically challenged, but I HAVE to get to the bottom of this! -
I have been trying to download apps from the app store and every time it tells me there is a problem with my previous billing and direct me to put in new billing information and every time i do that it still will not let me download any apps.
Have a look here > http://support.apple.com/kb/TS1646
-
I have huge lag with Safari's Reading List using a rMBP. I have probably 80 articles saved, which is likely the cause of the lag. Is there any way to export that list of articles so as to be able to delete them from Reading List but still have a record of the articles I intend to read?
I'm currently dealing with this issue myself, except that my rMBP has NO articles in the reading list. It's a brand new rMBP too, purchased just this week, with the 2.6 Ghz Processor & 16GB of RAM.
Let's see what we can find. I may just take it back to the Apple Store. -
The Airplay icon does not show on my Mac Pro, regardless that it is clicked on display. How can I do to see the Airplay Icon in order to connect my apple TV with my Mac Pro?
To check your model go to About This Mac (by clicking on the Apple icon, top left) and then select more info. If you wish to use mirroring you will need one from 2011 or later running OSX 10.8 or later. The alternative would be to use 3rd party software like Airparrot.
About AirPlay Mirroring in OS X -
How can i get apple to understand this is an authorize cord? It's the cord that came with the phone.
How can i get apple to understand this is an authorize cord? It's the cord that came with the phone.
cheriefromcatawba wrote:
How can i get apple to understand this is an authorize cord? It's the cord that came with the phone.
Is that what Apple told you when you took your phone and usb cord to the store? -
We are under strict regulations and monitoring at my company. Because of this, we have to define what updates are being installed during a patch cycle by KB Article. Two production networks and one test network. The installed updates have to be the exact
same in the test environment, run for a few days with no problems, and then we install them in our production networks. The issue is, not all of the software in the environments is identical.
I need to figure out a way to take failed/needed updates from production that are unapproved, export that list so I can approve all of those updates in the test env.. Then once I approve those and any other needed updates in test, I need to be able to export
all approved updates from the test env (which includes the needed ones from production) and import those approvals in production.
How can this be done?
Thanks!the easiest way will be to use a single wsus infrastructre for all your environments.
Tis blog article explains how to duplicate the approvals over groups:
https://thwack.solarwinds.com/community/application-and-server_tht/patchzone/blog/2013/08/06/duplicating-approvals-from-a-test-group-to-a-production-group
MCP/MCSA/MCTS/MCITP
Maybe you are looking for
-
Not really sure how this works, but here goes. I bought an IPhone on EBay over a year ago. 3GS. I found out I had to have it jailbroken since it had already been connected to AT&T. I did that and hooked up to Bell and it has beens working fine ever
-
Image from Photoshop is getting masked in black or something
I have a file that I flattened in Photoshop. It looks fine. I batch flattened a group from Bridge and it is the only one with this very strange issue. It was a document with a bunch of layers and when viewed in Photoshop or any other way it looks fin
-
I cant open iphoto -You can't open your current photo library using this version of iPhoto.
i cant open iphoto -You can't open your current photo library using this version of iPhoto.
-
When saving a PDF not all text is displayed
We have a user here whom uses Adobe Acrobat X Pro. When she opens the PDF in question, all text is displayed fine, however, if she makes a small change and re-saves the document then a lot of the text is not displayed - This will also happen if she
-
I have a sony icf-cs15ip and my iPhone 4S
I have had the Sony ICF-CS15IP for a while now. It always worked great with my iPhone 4S. Today I tried to use it and the phone stated that this is not an acceptable accessory. How do I fix this? Thanks