I buy iPod touch with face time ad after make restore face time disappear what can i do ????

please help me with this problem facetime disappear

Where did you purchase the iPod? If from one of the countries that prohibit FT, there is no official way to get FT on the iPod

Similar Messages

  • I have an ipod touch with ios 5.1.1 that wont connect to wifi. what can i do?

    have an ipod touch with ios 5.1.1 that wont connect to wifi. what can i do? Ive done a restore, recovery, and still wont connect.

    Does the iOS device connect to other networks?
    Does the iOS device see the network?
    Any error messages?
    Do other devices now connect?
    Did the iOS device connect before?
    Try the following to rule out a software problem:                 
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on your router
    .- Reset network settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - Wi-Fi: Unable to connect to an 802.11n Wi-Fi network       
    - iOS: Recommended settings for Wi-Fi routers and access points
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device. Not clear if you did this type of restore
    If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
    Apple Retail Store - Genius Bar

  • Ipod touch with Quick time streaming server

    Hello,
    I would like to test video streaming in the ipod touch with Quick time Streaming Server.
    Please let me know how to do that ?
    Best Regards,
    Geunhyung Kim

    Please let me know how to do that ?
    Unless there's an application in the iPhone application store which supports RTP, you can't.
    (34712)

  • TS1591 my ipod touch 2g is no longer being recognized by itunes why and what can i do i have reset it and everything

    my ipod touch 2g is no longer being recognized by itunes why and what can i do i have reset it and everything

    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here.

  • My daughter has an iPod Nano but just received an iPod Touch 5G but iTunes won't recognise the new device. What can we do?

    My daughter has an iPod Nano but just received an iPod Touch 5G but iTunes won't recognise the new device. What can we do?

    iOS: Device not recognized in iTunes for Mac OS X
    or
    iOS: Device not recognized in iTunes for Windows
    You need iTunes 11.1 or later on the computer.
    Does the iPod charge?

  • HT3302 My iPod Touch fell into the washer and now does not start. What can I do to fix it?

    My iPod Touch fell into the washer and now does not start. What can I do to fix it?

    If it is totally dry:
    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
    Apple Retail Store - Genius Bar       
    Apple will exchange your iPod for a refurbished one for this price. They do not fix yours.
    Apple - iPod Repair price      

  • HT1296 One Ipod touch has a different Apple ID than the rest. We are unable to sync Ipod Touch with our computer to transfer music we already purchased. How can we get this music transfered?

    How can I transfer music from our computer to an Ipod Touch with a different Apple ID?

    Go to Settings>iTunes and App Stores and tap the Apple ID listed and sign out and sign in with other ID
    You also may want to go to other places like:
    - Settings>iCloud
    - Settinge>FaceTime
    - Settings>Messages>Send and Receive and change the ID
    It may be best to go to Settings>General>Reset>Erase all Content and Settings and start over again and set up the iPod again with his account/ID

  • I would like to sync my ipod touch with my iMac but I'm afraid of losing data how can i do this without buying non apple software

    i have recently changed from windows to apple, i have my whole record collection on an ipod touch, i have successfuly transfered my music data from my old computer but i am affraid to sync the ipod touch incase something goes missing also for some reason i have numerous duplicates and dont want to have them on my touch i have seen that there is software on the market to help with this problem but i am reluctant to use non apple software on my new computer can anyone help.

    Tough spot if you want Apple only SW, no idea where you can get where you want without some decent 3rd party SW, which as a rule outshines Apple's SW by light years.

  • Ipod touch doesn´t sync  my Apps from my computer. why? What can I do? I payed for my Apps and I don´t want to buy it again.

    My ipod touch doesn´t sync my Apps from the computer. What can I do? I payed for my apps.

    Can you directly download the apps to the iPod?
    T not be charged again:
    Downloading past purchases from the App Store, iBookstore, and iTunes Store

  • My iPod Touch 2G 4.2.1 is acting up on me. What can I do?

    I have an iPod Touch 2G with an iOS of 4.2.1. I've had it since 2011, when I found it slightly beaten up but still usable in the bottom of an old sofa chair. I think that one of my relatives accidentally let it slip from their pocket, but that's another story. Since then, I've used it as my main portable Internet device. I've also jailbroken it. Unfortunately, the past few days have seen it work really badly, so much so that I had to reset the whole thing. Last night, I attempted to reset it. The instructions said that the reset would take about two hours to complete. But now, the thing keeps loading, shutting down, and re-loading and re-shutting down over and over. No main screen, just the Apple logo and my jailbreak logo, and then it shuts down and does it over and over and over and over. It's been almost 24 hours since I began to reset my iPod Touch. I'm so worried. I tried to disrupt the process by holding the home and power buttons at the same time, but no response. My computer can't even get it to respond.
    I cannot afford to purchase a newer model (or even an iPad) or have it repaired. I'm on food stamps and still looking for work. Plus, the iPod Touch's warranty ran out years before I came across it, so Apple can't send me a new one. I have another iPod, but it's an iPod Classic. I've had it for over four years and it's become an indispensable part of my life, and so has the iPod Touch. I'm extremely upset right now. If I took this to the nearest Apple Store's Genius Bar and asked for help, I would probably be laughed out of the store. I just don't know what to do.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer          
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. The appointment is free.
    Apple Retail Store - Genius Bar       

  • My ipod touch shows I have wi fi connection but no internet access, what can I do about this?

    I have a new ipod touch and it shows I have a wi fi connection, but I am not able to connect to the internet.
    Any suggestions?

    Try this first.  In Settings > WiFi: Turn wi-ff, then turn it back again.  If this does not work try Settings > General > Reset > Reset Network Settings.
    If you have never been able to connect and are using WPA security, make sure your password is correct.  If you are using WEP security, you're wasting your time as WEP is hackable in less than 30 seconds.  And the iPod often has problems with WEP.
    In any case, if you can't get it to work at home, try it in a place with free wi-fi.  If it works there the problem is probably with your router (this can be the case even if your router works with other equipment).

  • Ipod touch will not turn on after a restore

    I had my ipod serviced by 3rd party warrentee for a broken screen. i used back up before sending off to service. the ipod was returned to me in working order and i proceeded to restore my last back up and now the ipod will attempt to come on (apple logo) then stop after 7-10 seconds. itunes and computer will not recognize ipod since it is not on.

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that usually indicates a hardware problem and I would then contact the repair place.

  • HT2101 My IPOD touch just died. It only shows the apple icon. What can I do?

    I was trying to upload a change to an app and my IPOD died. It shows the Apple logo and notheing else

    Hello Tolhurst,
    We have an iPod Touch assistant that should be helpful in getting your iPod Touch working again.
    Frozen or unresponsive iPod touch
    http://www.apple.com/support/ipodtouch/assistant/ipodtouch/
    If you continue to have trouble getting the iPod Touch working again, I'd recommend putting the device into recovery mode and attempting a restore that way.
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Cheers,
    Allen

  • All of a sudden, my iPod Touch 4G won't connect to our Comcast internet provider. What can I do?

    All of a sudden, my iPod Touch 4G won't connect to our Comcast provider.  What can I do to get it reconnected?

    Have you tried any and all of the suggestions in this Apple support document?
    iOS: Troubleshooting Wi-Fi networks and connections
    B-rock

  • My mac book pro (2.66Ghz Intel core i7 4Gb ram) crashes every time I open iPhoto, browse photos or videos from Finder and work with slides, this started after I upgraded to mountain lion, what can I do??

    I updated my OS to mountain lion and since then my mac book pro is virtually useless, seeng pictures, videos, using graphics applications and Iphoto is impossible, the screen goes black, and the system restarts.
    This even happens sometimes at login, the login screen appears then the computer crashes and restarts, sometimes more than once, yesterday it even happened 6 times in a row before I was actually able to enter the password and log in.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac. 
    These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing. 
    Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects. 
    Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands. 
    Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply. 
    Launch the Terminal application in any of the following ways: 
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.) 
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens. 
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid. 
    When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign. 
    Step 1 
    Triple-click the line of text below to select it:
    kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}' 
    Copy (command-C) the selected text to the Clipboard. Then click anywhere in the Terminal window and paste (command-V). Post the lines of output (if any) that appear below what you just entered. You can do that by copy-and-paste as well. Omit the final line ending in “$”. No typing is involved in this step.
    Step 2 
    Repeat with this line:
    sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}' 
    This time, you'll be prompted for your login password, which you do have to type. It won't be displayed when you type it. You may get a one-time warning not to screw up. You don't need to post the warning. 
    Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step. 
    Step 3
    launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}' 
    Step 4
    ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null  
    Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting. 
    Step 5
    osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null 
    Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output. 
    You can then quit Terminal.

Maybe you are looking for

  • Block material for Sales Area & Customer.

    Hi. I want to block material for particular Sales area. For that i used  "X-distr.chain status" &" DChain-spec. status" in Saleas Org1 Tab of material Master. Now in Sales Order Creation i am getiing Warning message as "Material 95343431321 has statu

  • Output Condition Records based on Document Value

    I have a need to send/not send different pieces of output based off of Quote value. Example:  if a quotation is over $100 send a copy of the quotation to the field sales rep automatically.  And simultaneously if the quotation is under $4000 automatic

  • AWR and ADDM in general

    Hi, where can I find good easy material on net fro AWR and ADDM with examples and scenarios. Thanks rgds saaz

  • Trouble accessing the cloud

    How do I access the Creative Cloud? My 30-day trial expired. My company paid for my license.

  • How to decode Google map polyline from 64base to decimal number

    I need help decoding Google map polyline ASCII characters to decimal point. Can someone please help, I have tried few example on NI website but they do not produce desired results. I need something that is going to work like Googles decoder utility h