I can connect to wireless network, but it doesn't work

I am able to connect to my wireless network from my iPad and iPhone, but it's not working.

I am able to connect to my wireless network from my iPad and iPhone, but it's not working.
If you are able to connect to your wireless network as you state.....then can you provide more details about what is not working?

Similar Messages

Can connect to wireless network but no internet access

I have a PC that runs on Windows Vista and a wireless network using Airport Extreme. My PC can connect to the wireless network but I cannot access the internet. Windows Network Diagnostics states that 'A problem with your network router or broadband modem might be preventing an internet connection'. There should be no problem with my modem as I can access internet using my powerbook. When I run airport utility on my PC, there is an error message that states that 'An error occurred while trying to access the Apple wireless device. Make sure your network connection is valid and try again', 'error -6753'.

I am glad you brought this up. I am having the same difficulty. I run an iMac OS X 10.5.6 with an intel processor and a parallel system to get me on the Windows side. When I try to access the internet using my Airport extreme I cannot access any sites and the internet explorer page pops up with "The page cannot be displayed and sends me to try the diagnose connection problems on the toolbar method. However I can see my base station and all looks fine with the information there. I can also access the internet from my mac side of the computer. It would be nice to use the Windows side to gain access to the net because I have programs for the windows side that need updating. Anyone out there have any suggestions?

Can connect to wireless network but no internet?

Ok, I'm sure this is answered somewhere, but I'm tired.
At this point I'm not even sure if it can be done. But... I tried to connect to my mother's wireless internet using my Airport Extreme. I connected to the wireless but was unable to access the internet, or email. I tried manually setting the IP address, DHCP, router, DNS etc. But to no avail. It kept saying "Airport is connected to wireless ..., but it has a self-assigned IP address and may not be able to connect to the internet". I got it to accept the new IP address and finally it said " Airport is connected to wireless..., and is connected to the internet" but I still could not get on. It does say on her computer that it is protected by a key. But I used her password to get on and it recognized it? But her password was not the key.
I thought that I could connect to any wireless network with the password?
Can this even be done?
Thanks
A

Duane,
Thanks for the response. I did not see anything about MAC filtering enabled. It did say encryption was enabled. All I foud was the IP address, router, DNS etc. It is a WEP password and it did accept the password to log on to the network. It's Time Warner and she has a PC. I tried everything, set up new location. I'm going to try to log on to my friends wireless network and see if I can do so there. If my memory serves me right, the last time I tried to log on to a wireless network it didn't work either. Also my mother does not know much about it, someone set it up for her and she is one to not understand these "new fangled things". So...

WRT54G v6 - Can Connect to wireless network but can't access internet

Ok, this is my last resort for help. I spent two hours yesterday with linksys "chat" support to no avail.
First the techincal details:
OS for all machines = Windows XP
Laptop w/two adapters - one wired, one wireless
WRT54G v6 upgraded with 1.00.9 firmware
SpeedStream modem from DSL provider
I have manually set the IP, subnet mask, gateway, primary and secondary DNS for my wireless adapter (using the Alternate Configuration in the Internet Protocol Properties of the Wireless Network Connection). When I connect to the wireless network I see that the IP, subnet, gateway and DNS server IPs are all correct (via ipconfig /all). I see that I am connected to my SSID (11.0 MBps, signal strength Excellent) however I can't access web sites (the server not found message appears in the browser) nor can I ping the router IP or any other IP (LAN or WAN).
My wired PC works fine with this router. My laptop works fine with this router when wired.
Anyone face a similar situation and have a solution? Thanks.

A new discovery...
When I disable the wireless security on the router, I am able to connect to the wireless network, ping the router and access the internet. So, there is apparently something wrong with the WEP security (although I am able to connect to the wireless network when WEP is enabled).
I am thouroughly confused. Any help is appreciated. Thanks.

NB200 Can connect to wireless networks, but cannot connect to the internet

I have been able to connect my Win XP netbook to my secure wireless network at home, other people's networks and public networks like the library and McDonalds. This week I'm away from home and discovered that while I can still connect to a number of different wireless networks, I cannot connect to the internet using Internet Explorer.
I've had this problem once before and fixed it by reinstalling Windows XP and all my other software. I have no idea why it has happened again. I'm hoping for a less drastic solution to the problem..?

Hi Nakia,
> I cannot connect to the internet using Internet Explorer.
Have you tested other browsers like Mozilla Firefox and does this work?
As MasterG wrote try to renew the IP address using the commend line.
Last week I had a similar problem and I could solve it by updating the WLAN driver. Just remove the driver, restart the notebook and install the newest one. :)

Can connect to wireless network but not to internet

Ok, so I bought a new AEBS and have finally managed to get it set up with my cable modem, and with security on so that the light is green, and not amber... the only problem now is that although I can connect to the wireless network that i have created using the base station, I cannot connect to the internet through it using my MacBook.
I don't have problem connecting my iMac to the net wirelessly using the base unit so am confused.
Anyone got any ideas?

It is described on Page 51 of "Designing AirPort Extreme 802.11n Networks" (http://manuals.info.apple.com/en/DesigningAirPortExtreme802.11nNetworks.pdf).

[SOLVED]wlan0 connects to wireless network, but internet does not work

I have a Compaq Presario A900 laptop just installed Arch on it, went through the wireless Wiki and also checked this thread: http://bbs.archlinux.org/viewtopic.php?id=65467 (similar issue but I don't use any proxy). It has Broadcom card, 4311 Rev 02. I tried both the b43-firmware and broadcom-wl AUR packages and b43 works with my card.
I have tried with the shell to connect but "iwlist wlan0 scan" always returns no results. (Yes, I did try ifconfig eth0 down first as well before bringing wlan0 up). So I have tried wicd and it worked to connect me to my wireless network which uses WPA, and signal shows ~80% strength, however ping google.ca, nothing works as far as connected to the net.
Any output I should show I will if I have forgotten, thanks very much for your help!
Last edited by colbert (2009-05-27 00:40:48)

Thanks for your help hokasch, however it was a result of needing to reboot and have proper daemon in rc.conf, and it has been working great last few days Thanks!

I can see my wireless network,but my ipod4 will not let me connect to the network?

I can see my wireless network, but my ipod4 will not let me connect to it. When I try it tells me that it is unable to join. I can access the network on my laptop fine. I am also having trouble with connecting my ps3. It has the exact same problem. Can anyone help me?

The ps3 problem tends to indicate a router problem. Have you powered off and then back on your router?
For the iPod try:
- a reset:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Reset Network settings: Settings?|>General>Reset>Reset Network Settings
- The troubleshooting here:
iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections

HT4259 I have a Netgear wndr3400 and I can "join a wireless network" but can not "extend a wireless network" on my Airport express. Does anyone know why?

I have a Netgear wndr3400 and I can "join a wireless network" but can not "extend a wireless network" on my Airport express. Does anyone know why?

Sorry, but "Extend a wireless network" is a proprietary Apple setting that will only work if you have another Apple router.
It is not compatible with devices from other manufacturers.

Hey ! I was senting a text and my iphone suddendly off. I try to press "home" and "start" and to connect it at itunes but it doesn't work! Can you help me please

Hey ! I was senting a text and my iphone suddendly off. I try to press "home" and "start" and to connect it at itunes but it doesn't work! Can you help me please

Hold HOME and START at the same time until an Apple logo appears. This is called a "reset", and essentially it reboots iOS. You will need to hold for about 10 seconds.

Hp C4580 printer won't connect to wireless network, but see network is available.

I've sat through quite a few of the threads here with regard to photsmart C4580 printer not connecting to wireless network.
My issues started with a cartridge issue, which I resolved with a new cartridge, but only after trying out different solution offered on HP forum.
Now printer won't connect to my network which it has been connected to for over 2 years with no issues. The wireless network is working perfectly fine and I even printed out a HP photosmart C4500 series connectivity status and in this report printer can see the network I need to connect to.
I've tried downloading various programs from Scan doctor to complete install of all HP programs and even tried installing printer from Windows 7 "add a printer", but none can see this printer.
lastly I was hoping trying to locate IP address for printer which looks like it may help, but report says IP Address "not applicable".
I believe printer, wireless network and PC are working correctly, this there a way to switch printer to online so it can be seen.
Help would be great.

Hello there! Welcome to the forums @Cushionman ,
I noticed your post about the issues you are having with connecting the printer to your network. I am wanting to offer you my suggestion that might help you out!
Click this link and then choose Windows 7, and "Solution two: Manually resolve the issue", and follow the steps from there: The Printer is Not Found During Wireless Network Installation in Windows
Let me know the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Can connect to wireless router but not to the internet

Please Help, I have a WRT150N and I can connect to my wireless router by it will not connect to the internet from there, even though the internet, wireless, and security lights are lit up. If I plug a cord into the back of the router and then into my computer, I can connect to the internet, but once I disconnect the cable, I can still find and connect to my wireless router, but it will not connect to the internet from here. Under access it says "Local Only", I have the security type set to "Shared" under the security properties, and set to "WEP" with WEP key #1 entered. I have spent about 4 hours working on this problem now and could really use some help. Thanks.

Type ipconfig /all in command prompt(cmd.exe) to see whether it displays valid and correct IP, netmask, gateway and DNS info. If not, take a look on these cannot connect to wireless network problem and using ping to troubleshoot network problem articles to get more ideas. Hope it helps..

EA3500 Phones can connect to wireless router, but cannot transfer data

Ok, Since Cisco is completely helpless on helping me (this is why we are switching from Cisco stuff to other brands like Aruba at my work) I was thinking you guys would help me. I got hanged up twice on this problem. TWICE.
So, my phone and my friends phones can connect to the wifi but I cannot receive nor send data from it. The phones work completely fine elsewhere. Here is the kicker, my computer works completely OK on the router and my phone used to work for 3-4 hours before this issue started going again. Now it is constantly. I restarted the modem, default reset it and still nothing. I get an IP address too and it stays connected. Any help. Cisco thinks its the phone, but its multiple phones that are having the problem and my phone and other works completely fine at other places.

The quickest way to get your phones working is to configure them staticly. More than likely........either your modem, your firewall, your router, or your ISP is blocking the proxy. Try using Google Public DNS. 8.8.8.8 and 8.8.4.4 Disable any proxy blocking features of your modem or firewall.
Sometimes simply changing the DNS on your router to Google Public DNS might fix the problem.
http://www.ehow.com/how_8275878_put-static-ip-iphone.html
http://unlockforus.blogspot.com/2012/05/how-to-use-static-ip-address-at-android.html
http://homekb.cisco.com/Cisco2/GetArticle.aspx?docid=816d2158e9e84c6da97fc236b4234ae2_3954.xml&pid=8

Can't connect to wireless network but wife can...

Hi. I've just bought a Macbook pro. I am trying to connect it to a wireless network. The macbook finds the network (and others), but after I give the correct password it says 'authentication failed'. The weird thing (to me) is that my wife can connect to the same network with her macbook with no problems. These are my Airport details (no working connection)
Software Versions:
Menu Extra: 6.2 (620.24)
configd plug-in: 6.2 (620.15.1)
System Profiler: 6.0 (600.9)
Network Preference: 6.2 (620.24)
AirPort Utility: 5.4.2 (542.23)
IO80211 Family: 3.1 (310.6)
Interfaces:
en1:
Card Type: AirPort Extreme (0x14E4, 0x8D)
Firmware Version: Broadcom BCM43xx 1.0 (5.10.91.26)
Locale: ETSI
Country Code: DE
Supported PHY Modes: 802.11 a/b/g/n
Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
Wake On Wireless: Supported
Status: Not Associated
and these are her's (working connection)
Software Versions:
Menu Extra: 6.2 (620.24)
configd plug-in: 6.2 (620.15.1)
System Profiler: 6.0 (600.9)
Network Preference: 6.2 (620.24)
AirPort Utility: 5.4.2 (542.23)
IO80211 Family: 3.1 (310.6)
Interfaces:
en1:
Card Type: AirPort Extreme (0x14E4, 0x8D)
Firmware Version: Broadcom BCM43xx 1.0 (5.10.91.26)
Locale: ETSI
Country Code: DE
Supported PHY Modes: 802.11 a/b/g/n
Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140
Wake On Wireless: Supported
Status: Connected
Pretty similar......
We are both running 10.6.2 with all the latest sofwtware updates. Does anyone have any suggestions as to what might be up? The router is a Netgear DG834Gv5, again with the latest firmware. Security is WPA2.
Thanks in advance,
wrathkeg

Two things I'd check first:
1 - in your router, do you have mac address filtering turned on? If so, add the mac address (Airport id) of your MacBookPro to the 'Wireless Station Access List' in your router. You can find your Airport id under *System Prefs > Network > Airport > Advanced > Ethernet* .
2 - in your MacBookPro, turn Airport OFF. Then go into *System Prefs > Network > Airport > Advanced.* In the Preferred Networks box, delete the wireless network you are having trouble authenticating with. Click OK, then Apply. Exit System Prefs. Then turn Airport ON. Find the network; re-enter your password. See if that fixes things.

Can't connect to wireless network but connects if I move it 1 meter

Hi all,
I've had my 27" iMac Intel Core 2 Duo for over 3 months now with no issues, but suddenly over the weekend I can no longer connect to my network.
Sometimes I can see my network listed (but the signal is now very weak when it used to be very strong) and when I try to connect I get a "Connection Timeout" error. Othertimes I can't even see my network.
If I move my whole mac about 1 meter "closer" to the router (it sits downstairs, my mac upstairs) it connects fine. But as soon as I put it back on my desk, where it has been sitting for the past 3 months, the connection drops out or it can't find the network. (I can't leave it "closer" to the router, as that would mean I'm sitting on the floor right in my room doorway...)
All other PC's, laptops, my MacBook and iPhone all connect fine. In the MacBooks case, it connects fine in exactly the same spot as where my mac had been sitting for the past 3 months.
I'm using a Belkin N150 wireless router which is supposed to have a range of 300m (my house is definitely not that big!) and using a WPA2 Personal password security setting. As I said above, no issue before this past weekend (same router, same settings).
I have tried the following:
- restarting router, modem, computer (in various orders) to no avail
- deleting the system configuration folder, re-starting, etc.
Just wondering if there's something I'm missing? Or whether or not it's to do with the wider issue of connecting that people seem to have? I thought it may be different since I can connect if it sits somewhere else...
Any help wold be appreciated since my support has run out!
Thanks in advance!
Message was edited by: chuppachup

Yeah I've tried moving it but unfortunately I'm a bit constrained as to how far I can move it (aprox 20cms each way). There are lots of ethernet cables plugged in and they all run behind what is, a very solid, very big desk/shelving thing.
However, the position of the router hasn't changed in the past 3 months.
I've also tried disconnecting the cordless phone which sits in the same room and moving any extra cables around the router to no avail. But none of these things are new either.

I can connect to wireless network, but it doesn't work

Similar Messages

Maybe you are looking for