I can not get the ringer symbol off of my home screen on a frequent basis.

I can not get the ringer symbol removed from my home screen on a frequent basis.  I have tried pushing the volume keys and the mute button, but nothing helps. 

Hold Sleep Button with Home Button toghether until it restarts Always it takes 8 to 15 seconds, after it restarts leave the sleep button and remember do not leave the home button it automaticlly switches to DFU mode.

Similar Messages

  • After update to OS4.2.1 I can not get the ringer to work for incoming calls

    after update to OS4.2.1 I can not get the ringer to work for incoming calls. If I set Vibrate on, that's the only notification I get. Tried everything including blowing away ALL my apps and restoring phone to new. Lost all my apps but the ringer still won't ring

    God Bless u! LOL I have an otterbox case on my phone and had no clue that the mute button was there....Thank you so much!! The volume on my movies & everything else worked...even when I would go into "settings" and adjust the volume of the ringtone. I knew it was something simple...Thanks again..

  • My nephew put the Hallmark Channel on my computer and I can not get the sound turned off.

    My nephew put the Hallmark Channel on my computer and I cannot get the sound turned off.

    Is this a separate application? Where did your nephew install it? If you do a force quit (command - option - esc) does it show up so you can force quit it?

  • We are an inner city youth organization, we purchased 30 emac computers for the kids.we can not get the old password off the accounts page for the internet

    We can't get on to the internet, all the account numbers are correct and it says we are connected, but the last step it wants to get the old password in order for us to open on to the internet. How do we find and remove the old password.
    We can't find the password or get it from the school we received the computer from.

    Go to System Preferences
    Click Network
    Highlight AirPort and click Configure...
    Choose “By default, join: Preferred networks”
    Select your access point and Remove your access point with the minus button.
    Launch your keychain access in Utilities and delete your access point keychain entry.
    Reboot
    Go back to the “By default, join:” page and click the plus this time to add your access point. Enter the correct password, save, reboot.
    Instead of joining it from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed. Before I went through network diagnostics and all of that stuff in system preferences, and then I tried the "Join Other Network" method, and now it works like a dream.

  • Can not get the browsers to open their default home page so are safari,firefox,chrome, can not get the browsers to open their default home page so are safari,firefox,chrome

    Safari won't recognize www.apple.com  if by chance opens the home page when I request another website , it tells me I am not connected to internet , but I am , then I try to go to firefox  and i get the same problem , then  I wnet to another place  (at&T htspot and all is working perfect all brwser work normal . I am assuming this has to do with my house network , but all other computers do not have a problem they work ok . So I ask is there a problem with my computer with the network , how can I see if that is the case

    The standard arch kernel includes all the required modules, at most you need to load them explicitly listing them in MODULES in /etc/rc.conf
    You need also the hw specific stuff, that is i915 and intelagp. Check lsmod and see if they are loaded. If they are not, inspect dmesg and see if udev tries to load them and fails for some reason.
    I remember some cases where intelagp and i915 are not loaded by udev in the right order, if this is your case you can try to list them in the right order in MODULES.
    There should be no need to recompile the kernel or to install a particular version of dri (just use the arch packages for mesa, libdrm etc; but I guess you have them already)

  • Guided access has Ben activated no password I can not get the red slider bar to shoe up when I hold the off and the home bottom down, it comes back to sarfri , I also tried  over ten times to enter a passcode, but no go

    Guide access has been activated, never set a pass word,I can not get the red slider to come up by holding the off and home button, tried entering a wrong pass word 10 time to reset it but it will not . Can only use Safari.

    Step by step, how did you arrive at seeing this agreement?

  • I have Adobe Photoshop Elements 10. It came installed on my HP Desktop. I am can not get the warp text tool to work. It has worked in the past. Once I click warp text, the little window does not pop up, and if I try to do anything else after I click warp

    I have Adobe Photoshop Elements 10. It came installed on my HP Desktop. I am can not get the warp text tool to work. It has worked in the past. Once I click warp text, the little window does not pop up, and if I try to do anything else after I click warp text, it wont let me. Just sounds the ding, alert, can still slightly navigate the program but can not use any other tools after clicking warp text. I just have to open task manager and close the program. not sure if I'm doing something wrong or maybe I just need to uninstall and re install. Having trouble finding out how to uninstall and reinstall because the program came pre installed on my desktop.

    It actually sounds like the warp text window is opening off screen.
    Resetting the photoshop elements 10 preferences should fix it.
    *Press and hold the Shift+Ctrl+Alt keys just after you start the launch of the photoshop elements 10 editor
    *Keep holding the keys down until you get a dialog asking if you want to delete the adobe photoshop elements setting file
    *Press Yes

  • My aperture library will not open after restoring my whole computer after a kernal panic.  I can not get the Aperture troubleshooting menu to open...any help?

    My aperture library will not open after restoring my whole computer after a kernal panic.  I can not get the Aperture troubleshooting menu to open...any help?

    Leonie,
    Fisrt let me thank you for your reply and assistance!  So here is the problem with so more detail...I was not sure I was going to get any replies ; )
    I restored from a time machine back up.
    History of Failure:
    I was trying to launch Aperture when the kernal panic occured.  My computer had been closed, and asleep and the battery was dead.  I plugged in charger and it was restoring/waking up after being asleep/shutting down from dead battery.  I launched Aperture from the dock and as soon as it opened the kernal panic occured.  After that the computer would not turn on.  It would try to boot then it would shut off.  I even tried to safe boot to no avail.  I went to the Apple store and they told me that the only thing I could do was restore whole computer from back up.  So thats what I did.
    Since then my previous aperture library: "2011" will not open.  I have created a new aperture library "2012", and it runs fine.  I have added new photos for about the past month...no problems. 
    When I launch aperture with 2012 library then try to switch libraries, I get the following prompt: "The selected library is from an older version of Aperture and requires a relaunch to switch."  I choose "Relaunch" and I get the following warning prompt: "There was an error opening the database for the library “~/Pictures/Aperture Library 20111.aplibrary”."  The only option is "Quit"
    Both libraries are version 3.2.3
    Computer stats: 3.06 GHz Core 2 Duo, 8 GB 1067 MHz DDR3 RAM, OS X 10.6.8
    I have tried to launch aperture troubleshooting by holding option+command from both the aperture icon and from the library file, neither will launch the troubleshooting feature.
    I am ok with computers, but not a whiz (mechanical engineer)...to me it seems as though there is a corrupt path or file or some sort of "check" that is failing, becuase the failure occurs so fast after trying to launch aperture. Maybe that doesn't make any sense but just a thought.
    I hope that you may be able to provide some insight.  Thank you again for you time and I hope that you have a nice day!
    Mike

  • I can not get the iPad to connect to the internet thru the router it shows the modum but will not connect

    I can not get the iPad to connect to the internet thru the router it shows the modum but will not connect it keeps saying choose a netwokand the IP Address it automaticaly puts in is wrong?

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    Additional things to try.
    Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    On your iPad go to Settings > General > Reset > Reset network settings and see if that enables you to connect.
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
     Cheers, Tom

  • I can not get the WiFi to sync to ipad mini

    i can not get the wifi to sync to my ipad mini. i have reset the setting 4 times and nothing i have turn my wifi off and on and nothing. i keep getting asked to retype my password and when i pressed join after it isnt enabled to connect help ?? do i need to take this in store ?

    I assume that you cannot connect to the internet because you don't sync to WiFi. Perform the following steps in the order listed and see if you can connect then.
    Go to Settings>WiFi>Tap the blue arrow next to your network name>Tap Forget this network in the next screen.
    Reset your router. Unplug it from power for about 30 seconds and then plug it in again.
    Go to Settings>General>Reset>Reset Network Settings.
    Reset your iPad. Reset the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider if it appears on the screen - let go of the buttons. Let the iPad start up.
    Go to Settings>WiFi>Tap your network name, enter your password, tap Join.

  • Can not get the screenpicture to fit the screen.

    can not get the screenpicture to fit the screen. problem acurred after hooking up to an external screen. tried everything in screensettings, but the screenpicture is larger than the screen

    When you slide the cursor to the edge of the screen, does the screen image scroll, allowing you access to everything (menu bar, Dock, etc.) even though you can't see all of it at once?
    If it does, go to the Apple menu and open System Preferences > Trackpad. Is the box for "Screen zoom" checked, under "Two fingers"? If so, press the Control key and drag two fingertips downward (toward you) on the trackpad. Does the screen image zoom down to normal size?
    Another possibility is pressing Option+Command+8. If System Preferences > Universal Access > Seeing > Screen Zoom has accidentally been turned on, this will turn it off and return your screen to its normal size.

  • I can not get the temperature to work.

    Howdy
      I just got my MSI FX 5900XT yesterday and it is running fine. However I can not get the temperature to show on it. I have tried everything I can find on the forums like the different registry hacks and such. And it still does not work.
    In the one program 3D Turbo when it is first starting up it looked like the temps are trying to work then they just shut off. It stats to lite up and stuff they just goes down.
    Anyone know of another program or something else that I can try to get it to work ?
    Again I have tried everything that I have found on these forums that people have suggested so do not say try that stuff.
    I know this card has a temp probe as the 5900XT cards from other companies works fine people tell me. So unless MSI done something and took it out it should be there and be able to work just fine.

    Quote
    Originally posted by The Black Wibble
    Every piece of information about the card is obtained through the device driver so I say it is a driver problem.  I'd uninstall the driver, remove all traces of msi/nvidia driver binaries and config files using drivercleaner.  Deleting all references in the registry to MSI or nvidia might help, too, before rebooting and installing nVidia's 53.03 drivers.
    Tony.
    I purchased the card also from newegg and i have yet to get the temp sensor to work. I read in one reveiw that the chip for that is not in this card. Also that the overclocking program from Msi should not be used. I have searched all over for some info on the dynamic overclock technology DOT .The only mention of it is on the motherboard overclocking but it looks like its part of the video driver ? I have had very poor results trying to overlclock this card. 3d clock 450 ram 730 locks up all the time . I also run a amd 2400
    [email protected] Let me know if im missing something on this card or not  but dont want the hazzel of returning it

  • Can not get the Cisco TSP to show UP - 2003 64bit

    Can not get the Cisco TSP to show up on the list of Providers in Phone and Modem Options- Advance tab. Installed ver. 4.1, it seems to install correctly, with no errors but when I restart the server, there is no Cisco TSP001.tsp in the providers list. It works perfectly on my Windows 2003 servers, but will not work on this new Windows 2003 64 bit server. Any tricks to getting this to load?
    Thanks
    Keith

    Hi
    There is no 64-bit TSP yet. Whilst 32-bit apps will work OK for the most part on 64-bit via the WoW function, drivers tend to not be so flexible, and that's what TSP is...
    You'll have to bother your Cisco accounts folks to get this prioritised, it is upsetting a lot of people...
    Aaron
    Please rate helpful posts...

  • I have IMac 10.7.5 Lion I use I forgot the password and I did a few fixes from the we sites, which did not work and now I can not get the computer to reboot the gray screen comes on and if a shift c I get a load bar and it goes half way and help

    I have IMac 10.7.5 Lion I use I forgot the password and I did a few fixes from web sites, which did not work and now I can not get the computer to reboot the gray screen comes on with the apple and if a shift+c, I get a load bar and it goes half way and stops, I can get into the black screen area with the hard drive info
    I did the following:   mount -uw /    rm/var/db/.AppleSetupDone    shutdown/uses/us  reboot Ok I know I should not have, but now I need help to reboot and hopefully not lose everything on the desk top, Linda Markle

    You did the wrong things. In the future it's a good idea to remember not to do something when you don't know what you are doing and what happens when you do it.
    Forgot Your Account Password
    For Lion, Mountain Lion, or Mavericks
        Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
         When the menubar appears select Terminal from the Utilities menu.
         Enter resetpassword at the prompt and press RETURN. Follow
         instructions in the dialog window that will appear.
         Or see:
           Reset a Mac OS X 10.7 Lion Password
           OS X Mountain Lion- Reset a login password,
           OS X Mavericks- Solve password problems,
           OS X Lion- Apple ID can be used to reset your user account password.

  • How do I get the itunes symbol off I just bought it today

    How do I get the itunes symbol off the Ipad2 I bought today?

    See Here for Getting Started
    http://www.apple.com/support/ipad/
    http://manuals.info.apple.com/en_US/ipad_user_guide.pdf

Maybe you are looking for

  • Verizon Wirless 4GLTE for Tarboro, North Carolina Edgecombe and Rocky Mount NC Nash/Edgecombe

    Hello Verizon Wireless! Could you please tell me when the release date for 4GLTE for Tarboro and Rocky Mount which is in Edgecombe and Nash County in North Carolina? Because, 4GLTE has service in Pitt County which is the next county from us which is

  • BPC Error while loading master data from SAP BW

    Hello Guru, I have NW BPC 7.5 installed on BW server. Currently i have started to work on one application where i have to load master data first. I am loading master data for cost center. I looked into the process chain "BPC: Import BW InfoObject mas

  • IPod touch will not turn on or sync with iTunes

    I was listening to music on my iPod and i paused it. When i looked back at my ipod it had a black screen so i figured it was just in like the sleep mode or whatever it is. but when i hit the button for the screen to come back up nothing happened. i t

  • Type the name and password of a user in the "(null)" group to allow this.

    To connect to wifi while in the recovery partition, I'm asked to authenticate the wlan's certificate, and in order to do that I'm asked for "the name and password of a user in the "(null)" group" to make changes to the Certificate Trust Settings. Any

  • Lack of connectivity to iBooks?

    I downloaded Maverick and with it came iBooks. When I click on the icon the iBooks Page opens and when I click on iBooks Store i get the message Cannot connect to iBooks Store. I have connectivity to iTunes and everything else on the internet with fu