I can send imessages but not receive them?

Apologies if this is a stupid question.
I just got an iPhone 5 and can send imessages without any trouble, but when I receive a message it says 'Text Message' in small grey writing above the message. Does this mean that people are unable to send me imessages? I know that the people I am messaging have imessage turned on because I am able to send them imessages.

Macrumors posted a solution for this.  I used it and it seems to have worked for me.
Here's what they said:
1. Turn off iMessage in Settings > Messages
2. Reset networking settings in Settings > General > Reset
3. Reenable iMessage in Settings > Messages
Source:
http://www.macrumors.com/2013/09/30/resetting-network-settings-may-fix-imessages -not-working-in-ios-7/

Similar Messages

  • I can send emails but not receive them. The sender address was rejected by the server

    i can send emails but not receive them. The sender address was rejected by the server.

    Your mail server doesn't like the sender's address for some reason, perhaps because his mail server has been blacklisted for spamming.

  • I can send iMessages but cannot receive them?

    I can send Imessages to my friends with iphones but when I receive them they come in as texts. When I asked my friends they were sending me imessages but i was getting them as texts. This happened with multiple friends. What is wrong with my phone?

    Try turning Imessage off, and use it like that. It won't have all the capabilties but it still should work.

  • Can send SMS but not receive after update...

    After updating my iPhone 4S to ios6 i have problems with receiving messages.I can send SMS but not receive. What to do?

    Although I don't believe in consequences, I think this might be one of them. My email was working fine until I installed my VPN. I use the Thunderbird email application, which I like a lot, for three Hotmail accounts and two Yahoo accounts. After installing the VPN I could receive mail but could not send it on any of my accounts. I contacted the VPN and they sent me some numeric IP Addresses to put in my account settings. One for the Hotmail accounts and one for the Yahoo accounts. I did as instructed and the email seemed to work okay. It was late in the evening and I went to bed. The next morning, I could send and receive emails on the Yahoo accounts, but could only send emails on all of the Hotmail accounts.
    I guess I'd like to know if anyone else is having this same problem. I'd hate to think it was just me. :-)
    I would like for Thunderbird to tell me if there is a way to change the outgoing server in the Account Settings, so I can enter the IP Address in there, or does the fact that I entered an IP Address in the Server Name box, cause it to override any other entries? Or should that even make a difference with me receiving mail?
    Also, at what time limit does Thunderbird send back a message that the connection to the server timed out? I continually get that message.
    I found a way to do a ping on the Hotmail server and the fastest response time for the last two days was 258.09 which seems very slow for a business computer. At least for a business that wants to stay in business. So is that time above the Thunderbird threshold of the connection time out message to be generated?
    Thanks for all your help and suggestions, Carole

  • I upgraded to lion today and just realized I am not receiving any mail. I can send out but not receive. i'm using a POP Road Runner account. Any help appreciated.

    I just upgraded to Lion today and realized I'm not receiving any mail. I can send out but not receive. I am using a POP server Road Runner acct. Any help would be appreciated.

    Try Mail->Window->Connection Doctor.  If there is a problem reported, try:
    Open Mail->Preferences and check your settings.
    If you still have a problem, Copy your settings (screen capture ⇧⌘4), delete account, and re-setup account

  • HT1430 hey, I just reset my Apple ID and suddenly much of my Iphone text history disappeared.  and I can send texts, but not receive any.  what do I do?  is this related to AppleID, or is the text issue from something else?  thx!

    hey, I just reset my Apple ID and suddenly much of my Iphone text history disappeared.  and I can send texts, but not receive any.  what do I do?  is this related to AppleID, or is the text issue from something else?  thx!

    Hi blyther,
    Thanks for using Apple Support Communities.  If you're unable to receive texts, see this article for troubleshooting steps:
    iOS: Troubleshooting Messages
    http://support.apple.com/kb/ts2755
    Cheers,
    - Ari

  • Cannot send iMessage, but I receive them.

    My friend switched from Android to iPhone 5s.  When he texts me, I receive it as an iMessage on my 5c, but when I respond, it is sent as an SMS.  How can I make my messages go through as iMessages?
    I have already turned iMessage off and back on.
    I am using iOS 7.0.4
    I can send iMessages to my other contacts who have iPhones.  It is just this one contact.

    Hi Snerts,
    Thanks for the question. Based on what you stated, it sounds like you are not sending imessages to one contact. I would recommend that you read this article, it may be able to help the issue.
    iOS: Troubleshooting Messages - Apple Support
    To resolve issues with sending and receiving iMessages, follow these steps
    Check iMessage system status for current service issues.
    Go to Settings > Messages > Send & Receive and make sure that you registered iMessage with your phone number or Apple ID and that you selected iMessage for use. If the phone number or Apple ID isn't available for use, troubleshoot iMessage registration.
    Open Safari and navigate to www.apple.com to verify data connectivity. If a data connection isn't available, troubleshoot cellular data or a Wi-Fi connection.
    iMessage over cellular data might not be available while you're on a call. Only 3G and faster GSM networks support simultaneous data and voice calls. Learn which network your phone supports. If your network doesn't support simultaneous data and voice calls, go to Settings > Wi-Fi and turn Wi-Fi on to use iMessage while you're on a call.
    Restart your device.
    Tap Settings > General > Reset > Reset Network Settings on your iPhone.
    If you still can't send or receive an iMessage, follow these steps
    Make sure that the contact trying to message you isn't blocked in Settings > Messages > Blocked.
    Make sure that the contact you're trying to send a message to is registered with iMessage.
    If the issue occurs with a specific contact or contacts, back up or forward important messages and delete your current messaging threads with the contact. Create a new message to the contact and try again.
    If the issue occurs with a specific contact or contacts, delete and recreate the contact in the Contacts app. Create a new message to the newly created contact and try again.
    Back up and restore your device as new.
    Thanks for using Apple Support Communities.
    Cheers,
    Mario

  • My iPhone 5s will send messages, but not receive them. Replies show up on my iPad. How do I fix this?

    Anyone know how to fix imessage and FaceTime issues with iPhone 5s?  I can send messages, but replies only show up on my iPad, not my phone. Can't FaceTime at all, just on iPad.  Says "waiting for activation". Or "Activation unsuccessful. Turn on iMessage to try again."  And a screen comes up "iMessage Activation. An error occurred during activation. Try again."  If I try to log in with my Apple ID, it doesn't work, either. Same problems for FaceTime.
    I have tried all the "fixes" I found on another thread, nothing worked. This is a replacement phone. My first one had problems with the touchpad not working, but the messaging and FaceTime were fine. The touchpad works on this phone. Any suggestions?

    Fixed!! My cellular/internet provider had to do a restore and now it works

  • I can send iMessages but not send texts?

    I don't know why but for some reason my phone will let me send iMessages but it won't let me send texts.
    Also, when I send an iMessage it uses my e-mail and not my number?

    Hi Friend,
    In Settings>>Message>>Send&Receive, set to be contact in your mobile number and email. Below you set to start new chat just with your mobile number.
    Hope it will be helpful

  • I can send emails but not receive any??

    Hey guys n gals,
    I'm new to Blackberry and to be honest I'm not the most technical person in the world!
    I have recently been given a blackberry pearl 8100.  have enabled the bolt on with 02 etc.
    I can send emails but i can't receive any - would really appreciate any help you can give me
    Thanks
    Solved!
    Go to Solution.

    Hello CWNI,
    Check out this KB article, it should help you
    http://www.blackberry.com/btsc/kb02857
    Hope that helps!
    More than likely, you use outlook or similar application on your computer for email and it is just not leaving a copy of the message on the mail server. 

  • Can send packets, but not receive packets

    Running Windows XP, my Internet was working fine and then stopped working. It still shows that I am connected to the Wireless Network and shows that packets are being sent, but not received. Will work directly from the cable, but not wireless. Tested Wifi card on other computer, that works, Internet is working on other computer wirelessly.
    Any options?
    Using Wireless-G Notebook Adapter with SpeedBooster WPC54GS
    Broadband Router WRT54GSMessage Edited by tiggerx40 on 10-09-200603:49 PM

    What is the router model number and version? You may find the model number underneath the router itself on one of the stickers.
    Anyway, if you are plugged in to the router:
    1) open up internet explorer and go to 192.168.1.1
    2) username: just leave it blank password: admin
    3) go to the wireless tab:
    You may change the ff:
    SSID - this is the name of your network
    Channel - signal of the router (suggested value is 11)
    ----> save settings after you have done the necessary changes
    4) go the wireless security (found on the subtab)
    set-up security:
    - suggested mode is WPA Personal
    If your router is a WRT54G v5-v6, go to the status page:
    - check the firmware version, if the firmware version belong to any of the ff. below then download and upgrade the firmware.
    ► 1.00.1
    ► 1.00.4
    ► 1.00.6
    ► 1.00.7
    ► 1.00.9

  • Can send mail but not receive -- connection doctor OK, GetInfo shows msgs

    In the last couple of days I stopped receiving email on my Mac in the Mail app, but not my PC. Both access POP3 accounts at the same ISP, different POP3 accounts. All software is patched to latest version using Software Update -- PowerMac G5 Dual, latest OSX version. On the Mac, connection doctor says I'm A-OK (internet connection, POP connection, SMTP connection.) Also, if I do a Get Info on the inbox and show messages on the server, it shows 75 messages on the server. I have not retrieved messages to my knowledge (so I don't think the server thinks I already downloaded them), and the "Messages that have been downloaded to my Mac" pulldown option in Get Info confirms this, by not showing any of the 75 messages in the Show all messages pulldown option. But -- Get Mail does nothing! I have tried rebooting, deleting and recreating the account, etc. Since I can get POP mail for another account at the same ISP on my PC, and I have touched nothing on the Mac, and all the diagnostics show the connection and POP3 chat is working perfectly, this very strange. I do not think I have applied any patches or anything that might screw it up, but who knows.
    The only strange thing that might be a clue is the little spinning status indicator next to the InBox label runs for about 30 sec or so before it decides not to do anything -- seems a little long. Any suggestions? Any way to do detailed debugging of the POP3 session to see if the Mac-server conversation is wanked up somehow?
    Thanks!
    David

    For POP accounts, Mail uses a file within the account folder to keep track of which messages have already been downloaded. Deleting it should cause Mail to download everything still on the server as if new. I don't think it'll work in your case, but try it anyway just to be sure:
    1. Quit Mail.
    2. In the Finder, go to ~/Library/Mail/POP-username@mailserver/.
    3. Locate one or two files named MessageUidsAlreadyDownloaded and move them to the Trash. Mail 1.x used MessageUidsAlreadyDownloaded to keep track of which messages had already been downloaded. Mail 2.x uses MessageUidsAlreadyDownloaded2 for the same purpose.
    You can use the Account Info window first to remove from the server any messages you don't want to be downloaded again.
    You may try creating a new user account in System Preferences > Accounts, set up mail anew there, and see whether the problem happens there as well.
    Another thing you may try is using a different method to connect to Internet, if possible. Also, if Preferences > Check for new mail is set to Every minute, changing it to something greater (e.g. Every 5 minutes) might help.
    Something that usually works is removing some messages from the server (download them with another mail client first, to avoid losing them). Sometimes, Mail chokes on a message it cannot download, and that prevents it from downloading the rest as well.
    Any way to do detailed debugging of the POP3 session to
    see if the Mac-server conversation is wanked up somehow?
    Detailed debugging no, but looking at the Console could be informative:
    1. Open /Applications/Utilities/Console.
    2. From the File menu, choose either Open Console Log, or Open System Log, or both, so that the Console application displays the contents of both system.log and console.log.
    3. Try to reproduce the problem and look at the bottom of the Console windows for messages that might be written there as a result. They may provide some clues as to what the problem is.

  • I can send messages but not receive.

    My iChat used to work fine. For some reason, however, now I can send messages that my buddies can read but do not appear in my chat box after I hit send. I can no longer read any messages my buddies send to me. I also cannot see chat room invitations that are sent to me. My Mac store people tell me they can find nothing wrong and it "works fine" when they use it. I thought perhaps it was my user account, but I can use iChat at work and on my husband's iMac with no problems. All the settings seem to be identical. I thought about setting up another AIM account, but my original works fine on the other computers.
    Oh, I am able to video chat with my husband. It seems to be only the text chat that does not work.
    Any ideas or suggestions?

    Hi,
    Chats that do Text Chat and then send files or Pics in the chat change it to a Direct IM
    This changes the Protocol iChat uses to send and receive data on.  (It swaps from port 5190 (Or whatever login port you have set) on TCP to using port 5190 on UDP)
    This means you have to have port 5190 open on your router to the UDP protocol.
    (Of course it has to be opened in such a way that two computer can use the port and protocol at the same time. (UPnP is method of choice)
    Group chats also use port 5190 on UDP
    This would seem to be the most likely thing with what you list about the account and the Computer working at a Store  (I take it they tested Your iChat Account there ? (testing their own account would prove very little)
    11:20 PM      Wednesday; August 10, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb( 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • I can send email but not receive on my iphone 3GS. Emails to my .me address are OK but not emails to the address hosted by Network Solutions. NS have checked my settings twice. I am using IMAP. Is this a problem with iCloud?

    I use IMAP email hosted by Network Solutions for my main email address. I can send and receive this OK in my Mac Mail on my MAC book and also on webmail. However my iphone doesn't receive these emails but it can send. I have checked settings on my iphone twice with Network Solutions but no luck. Emails addressed to my .me address are received OK. I have a suspicion this problem started when I signed up to icloud.
    my ISP is BTconnect
    Any ideas?

    Useful suggestions. In fact I had already deleted and re-entered the account details a few days ago without apparent success. The error message was along the lines of "cannot access the server".
    Anyway about an hour after your message, my emails started coming through after a 6 month gap!  - makes me think someone at Network Solutions monitors these discussions.
    Many thanks

  • I can make calls but not receive them on lync 2013

    For some reason I can not receive calls from anybody in Conference mode or PC to PC  in some users. What type of logs can I enable on lync to verify this? I tried disabling an re-enabling again the user on lync and some users seem to work this, but
    in others not. 
    Thanks for your help.

    If you have deployed the Lync Monitoring Server you can look at the CDR and QOE data for calls: http://www.microsoft.com/en-ca/download/details.aspx?id=890 If you haven't
    deployed the Monitoring server, it's recommended when doing voice: http://technet.microsoft.com/en-us/library/gg398199(v=ocs.14).aspx
    You can also use snooper to trace calls (4 part blog explaining): http://blogs.technet.com/b/nexthop/archive/2012/04/16/troubleshooting-lync-server-2010-with-snooper-part-1.aspx
    Please mark posts as answers/helpful if it answers your question.
    Blog
    Lync Validator - Used to assist in the validation and documentation of Lync Server 2013.

Maybe you are looking for

  • Scandisk flash drive not recognized by windows 7 desktop

    my Scandisk SDCZ36-032G Cruzer works on my laptop but not on my desktop pc This question was solved. View Solution.

  • Finding out JRE version

    I don't know, how to make a request for a new feature to JRE, but I have a suggestion for a very small enhancement: every now and then I need to check the version of the current default JRE in my machine, e.g. to check the current build of u10. So I

  • How to avoid Invalidation of Stateful Session Bean in case of an Exception?

    Hi developers, I'm working on a project using JSF, Toplink and EJB 3.0 using JDev. I'm using a statefull session bean that is stored in the session but when an exception occurs in a business method in the stateful bean the bean crashed and can never

  • Stacked events. Events get added on top of one another.

    I have noticed that using the "addEventListener" and coming back into a frame, I get multiple events tied to the same component. The design I am using jumps to an "I" frame (intermediate) and then back to the "M" frame (main) when the user performs a

  • Error applying patch for bug 4554072 (APEX 2.2.1 requirement)

    All, I am installing APEX 2.2.1 and is trying to apply the patch for bug 4554072. I have checked the OWA version: SQL> select owa_util.get_version from dual; GET_VERSION 10.1.2.0.0 And When I am trying to execute the privht8.sql script I get the foll