I can't access the internet from my iPad! I have Wi-Fi but my iPAD won't allow me to join. Any suggestions?

I have tried to reset my Wi-Fi settings. I have powered my iPad 2 off and still can't get it to join. There isn't anything wrong with the internet connection because my laptop is still working just fine. Are there any other ideas on how to get this to connect?

I am having a similar issue. ipad was working fine last night but this morning will not connect to wifi network. wifi is okay as am using it on my laptop. I have turned router on/off dozens of times, have disconnected all cables, unplugged form power, reset my ipad to factory settings, deleted my network and set up again, still no luck, airplane mode is off etc etc. very annoying...

Similar Messages

  • I have a iMac with a built in airport extreme card.  Does the imac act as a wireless router so that I can connect to the internet from my iPad by tethering through my iMac?

    I have a iMac with a built in airport extreme card.  Does the imac act as a wireless router so that I can connect to the internet from my iPad by tethering through my iMac?

    Depends which iMac exactly and your network setup, you can go into System Preferences and under the Sharing pane you can enable internet sharing from ethernet (or whereever you get your internet from) to Wi-Fi.

  • How can I access the internet on my ipad mini while wifi signal is strong, how can I access the internet on my ipad mini while wifi signal is strong

    how can I access the internet on my ipad mini while wifi signal is strong,

    Your question isn't clear enough. If it's a strong signal, you're good to go.

  • I can't access the internet from my home wi-fi.  It works on other wi-fi, and my wi fi is working on my h ome computer.  I keep getting a message that says it can't access the server

    I can't access the internet using my home wi-fi. My wi-fi is working on my home computer, and the itouch can access the internet at another person's home using their wi-fi.  I've looked in the settings, and can't seem to see any differences.....i'm a techno dummy - so please respond in very basic info

    Before resetting try restarting.  Or you can go to Settings from the home screen > Wi-Fi > your network and scroll down to 'Renew Lease' and press that.  When you do you should see a button labeled 'Renew Lease?' and another labeled 'Cancel'.  Select 'Renew Lease'.
    You can either back out of that screen back to the home screen or just use the return button to go back to the home screen.  Then select Safari and see if you can hook in.
    I have to go through that process every five or ten minutes or so when in the second story of our house - weak router signal up there.

  • I can't access the internet from itunes?

    I can't access the ITunes store from ITunes and CD titles aren't loading.
    Under one user ITunes locks up when I insert a CD

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Download the song on your syncing computer and sync via iTunes.
    Then delete/redownload as necessary.

  • Just set up our Apple TV and it works fine for NetFlix.  However want to stream photos and I Tune library from home computer but this computer accesses the internet thru a VPR at my wife's place of enployment. Other than a 2nd computer any suggestions?R

    Just set up Apple TV on home network. Works fine for NetFlix but we can't stream I Tune libruary or digital photos thru it to our home TV as because of my wife's work we bypass COX and access the internet thru a VPN offered by her employer.  Was told we either have to buy a second computer (two expensive for just these two functions) or keep turning on and off the VPN(not practical). Any other ideas? Thanks

    Does she need to access the internet through her employer, or is she just trying to access her internal network at work?
    If it's the latter, split-stream VPN clients (like Cisco AnyConnect) will split traffic so that only that directed at a particlar domain gets tunneled. 
    I have an AnyConnect client at home, but I normally only activate it when I'm using it, so I've never tested it with HomeSharing.  I'm currently traveling, but when I get home tomorrow, I'll try it out and let you know if it works.  If it does, your wife can check with her employer to see if she can configure AnyConnect to work with them.

  • I've updated my iphone 3gs from iOS 5 to iOS 6 and now I can't access the internet on 3g, can anybody help??

    I've updated my iphone 3gs from iOS 5 to iOS 6 and now I can't access the internet on 3g, can anybody help??

    I don't follow your instructions... mine goes Settings->General->Cellular and from there it's just on/off options for Cellular Data, Enable 3G, Data Roaming, etc. Or I could go Settings->General->Profile APN Carrier Settings but when I click that it just shows as verified but no Visual Voice APN or MMS Settings. If I click More Details it goes to Signing Certificate which has a bunch of parameters for unlockit.co.nz but I am unable to change anything.
    I just updated my iphone 3GS to IOS 6 and my internet (wifi and 3G), voice and text all work, but the only thing I can't do is send/receive pictures via text message. I am using At&t prepaid sim. I tried turning off the phone completely but I'm trying to avoid a complete restore.. at least until I can understand the problem better! Any help would be appreciated!
    Thank you!

  • I went from an I-Phone 3GS to I-Phone 5, I can make phone calls out but I can't access the internet when I am away from my WI-FI connection... any ideas?

    I went from an I-Phone 3GS to I-Phone 5, I can make phone calls out but I can't access the internet when I am away from my WI-FI connection... any ideas?

    but in the home with wireless internet access , it is continued when off, sometimes can not working,
    What does "it is continued when off" mean?
    And the same for "somtimes can not working"?

  • TS1398 I have connected my iPad 2 to my Mac Air over blue tooth.  Booth say they are connected to each other.  But I can not access the internet on the IPAD.  I can connect over blue tooth from my iPhone to my iPad with no issue.  Any thoughts?  Thank you

    I am trying to connect my Ipad 2 to my Mac Air over bluetooth.
    I can connect them to each other, and both machines say they are connected over bluetooth.
    However I can not access the internet on the Ipad...says it is not connected to the internet.
    Does anyone know if you can fix this?
    THank you

    Yes I tried this manyfold. But did not work.  Reading on, I took Tesserac's advice. Shut down router and computer.
    Start router after 15 minutes and wait another 10 minutes before starting the computer.
    Et voila.... everything is back in working order,
    Regards form Curacao, Dutch Caribean.
    Pete van Linden

  • Networks will "connect" over Wifi, but DNS resolution is impossible and I can't access the internet.

    My OSX 10.7.5 iMac (late 2011) will connect to my university's wireless network and thinks it's connected to the internet, but cannot resolve any DNS - and cannot actually access the internet on any browser or internet-utilising app. My university has 2 networks, a regular wifi one and an eduroam one. I have the same problem on both networks. My MacBook, running Snow Leopard, and my iPad (latest software) both connect to both networks just fine.
    Because it's my university's network, i can't reset my router or anything like that. I'm in halls. I don't think it's a network issue, because all my other devices are fine.
    I've searched high and low on these forums but haven't found anyone having exactly the same problem as me - I've heard of odd few minutes of people losing their connections in this manner, but my computer's been down now for hours and nothing. I've restarted it many times, even once in "Recovery Mode" and I'm getting nothing. I've followed instructions to flush my DNS cache, renew DHCP leases, I've tried manually inputting various DNSes I've found (eg the 8.8.8.8 and 8.8.4.4 google ones), none of which have worked.
    Using terminal, I can't ping either an http:// domain, or an IP address. Both get "timed out" as a response. I can't access the internet on any browser (chrome, safari, firefox), my google mail notifier, Skype, or my twitter app. Or anything else.
    I'm relatively computer literate, but I'm not particularly code-savvy, so I'd really appreciate it if I could get some step-by step help on here, bearing in mind what I've already tried. I'm really worried, because it all seems to have happened completely out of the blue. Last time I updated was some time a couple weeks ago; I update whenever my software update beeps at me.
    Thanks.
    link.

    Go step by step and test.
    1.Power Cycle
       Power off the router. Unplug it from the wall. Wait a while.
       Plug it back to the wall. Power the router on. Wait until all the lights are lit properly.
       It will take a while.
      Restart the computer.
      Start up in Safe Mode.
       http://support.apple.com/kb/PH11212?viewlocale=en_US
    2.  Turn off Extensions, if any.
         Safari > Preferences > Extensions
    3. Turn off proxies, if selected.
         System Preference > Network > Advanced  > Proxies Tab
         Under "Select Protocol", uncheck any box if selected.
         Click "OK" then  "Apply"
    4. Uninstall anti-virus software, if any.

  • UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION

    Dear All,
    I have a site-to-site connection  from point A to point B. From point B i am unable to access the internet from local internet provider.
    I am trying to ping from 192.168.20.1 the dns 8.8.8.8   but i receive the  message "destination net unreachable".
    When i run "show ip nat translation" i receive nothing.
    The vpn connection is working properly, i can ping the other side 192.168.10/24
    Below is the configuration of the cisco router on point B.
    dot11 syslog
    ip source-route
    no ip dhcp use vrf connected
    ip dhcp excluded-address 192.168.21.254
    ip dhcp pool voice
     network 192.168.21.0 255.255.255.0
     default-router 192.168.21.254 
     option 150 ip 192.168.5.10 
    ip cef
    ip domain name neocleous.ru
    ip inspect name IOS_FIREWALL tcp
    ip inspect name IOS_FIREWALL udp
    ip inspect name IOS_FIREWALL icmp
    ip inspect name IOS_FIREWALL h323
    ip inspect name IOS_FIREWALL http
    ip inspect name IOS_FIREWALL https
    ip inspect name IOS_FIREWALL skinny
    ip inspect name IOS_FIREWALL sip
    no ipv6 cef
    multilink bundle-name authenticated
    vty-async
    isdn switch-type primary-net5
    redundancy
    crypto isakmp policy 5
     hash md5
     authentication pre-share
     group 2
    crypto isakmp policy 10
     encr aes
     authentication pre-share
     group 2
     lifetime 28800
    crypto isakmp policy 50
     encr 3des
     hash md5
     authentication pre-share
     group 2
    crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
    crypto isakmp invalid-spi-recovery
    crypto isakmp keepalive 10
    crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac 
    crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac 
    crypto ipsec df-bit clear
    crypto map CryptoMAP1 ipsec-isakmp 
     set peer [ip address]
     set transform-set TRANSET 
     match address CryptoACL
    interface FastEthernet0/0
     description Primary Provider
     ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
     ip access-group outside_acl in
     ip mtu 1390
     ip nat outside
     ip virtual-reassembly in
     load-interval 30
     duplex auto
     speed auto
     crypto map CryptoCY
     crypto ipsec df-bit clear
    interface FastEthernet0/1
     description TO LAN
     no ip address
     load-interval 30
     speed 100
     full-duplex
    interface FastEthernet0/1.1
     description DATA VLAN
     encapsulation dot1Q 20
     ip address 192.168.20.254 255.255.255.0
     ip access-group inside_acl in
     ip nat inside
     ip inspect IOS_FIREWALL in
     ip virtual-reassembly in
     ip tcp adjust-mss 1379
    interface FastEthernet0/1.2
     description VOICE VLAN
     encapsulation dot1Q 21
     ip address 192.168.21.254 255.255.255.0
    interface Serial0/2/0:15
     no ip address
     encapsulation hdlc
     isdn switch-type primary-net5
     isdn incoming-voice voice
     no cdp enable
    interface FastEthernet0/3/0
     no ip address
     ip access-group outside_acl in
     ip nat outside
     ip virtual-reassembly in
     shutdown
     duplex auto
     speed auto
     crypto map CryptoCY
    ip local pool VPNPool 192.168.23.2 192.168.23.10
    ip forward-protocol nd
    ip http server
    no ip http secure-server
    ip nat inside source list nat_list interface FastEthernet0/3/0 overload
    ip route 0.0.0.0 0.0.0.0 [default gateway ip]
    ip access-list standard VTY
      permit 192.168.20.0 0.0.0.255
    ip access-list extended CryptoACL
     permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
     permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
     permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
     permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
     permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
     permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
     permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
     permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
     permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
    ip access-list extended DFBIT_acl
     permit tcp any any
    ip access-list extended inside_acl
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
     permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
     permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
     permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
     permit ip host 192.168.20.253 host 192.168.3.21
     permit ip host 192.168.20.254 host 192.168.3.21
     permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
     permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
    ip access-list extended nat_list
     deny   ip host 192.168.20.254 192.168.10.0 0.0.0.255
     deny   ip host 192.168.20.254 192.168.3.0 0.0.0.255
     deny   ip host 192.168.20.1 192.168.3.0 0.0.0.255
     deny   ip host 192.168.20.1 192.168.10.0 0.0.0.255
     deny   ip host 192.168.20.2 192.168.3.0 0.0.0.255
     deny   ip host 192.168.20.2 192.168.10.0 0.0.0.255
     permit ip host 192.168.20.1 any
     permit ip host 192.168.20.2 any
     permit ip host 192.168.20.254 any
    ip access-list extended outside_acl
     permit gre any host [ip address]
     permit esp any host [ip address]
     deny   ip any any
    ip sla 2
     icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
     frequency 180
     timeout 500
    ip sla schedule 2 life forever start-time now
    logging 192.168.3.21
    route-map DFBIT_routemap permit 10
     match ip address DFBIT_acl
     set ip df 0
    route-map ISP2 permit 10
     match ip address nat_list
     match interface FastEthernet0/3/0
    route-map nonat permit 10
     match ip address nonat_acl
    route-map ISP1 permit 10
     match ip address nat_list
     match interface FastEthernet0/0

    You cannot access internet, because all traffic is tunneled for VPN !!!!
    Please see cisco tech documentation and bypass traffic for internet.
    eg.  if lan traffic is going from site a to site b  then through vpn
          else
           lan traffic to internet (any) should be out thorugh the vpn .

  • HT1222 Since downloading the IOS7 I can't access the internet via a wifi.  I would like to remove it, is it possible?  I have the ipad2

    Since downloading the IOS7 I can't access the internet via a wifi.  I would like to remove it, is it possible?  I have the ipad2

    Sorry, no. Apple does not support downgrading.
    Have you tried to go into your settings, reset, reset network settings? It'll erase your current network from your iPad and let you start over.

  • How to make Firefox access the internet from Oracle Ent. Unbreakable Linux?

    Hello
    I have a Dell Duo Core x86 laptop that multiboots Windows 2003 Server, Windows XP and Oracle Enterprise Unbreakable Linux. I use Internet Explorer to
    access my email while at the library so I know my laptop can access the internet. I just installed the Oracle Enterprise Unbreakable Linux in text mode and
    I can still access the Internet but only if I use one of the Windows operating systems which is why I am keeping them for now. The reason is because when I
    use Oracle Enterprise Unbreakable Linux, when I select Firefox to access the internet I get these messages:
    "Server not found
    Firefox can't find server at www.hotmail.com
    -check address for typing errors
    -if unable to load pages check network connection
    -if computer or network protected by firewall make sure Firefox permitted to access
    web"
    None of those reasons are true for not gaining access to the internet. I want to use Oracle Enterprise Unbreakable Linux from now which is why I installed
    but I need to know:
    1) Why do I get the "Server not found" and the other error messages when I try to access the internet using Firefox and what do I have to do to make Firefox
    access the internet successfully?

    Hi,
    First you must confirm your laptop with Oracle Enterprise Unbreakable Linux can access internet.
    Please open a terminal, input the following command
    1.ifconfig
    2.cat /etc/resolv.conf
    Regards
    Jason

  • HELP !!! I can not access the Internet Recovery In Mac Pro!

    HELP !!! I can not access the Internet Recovery on my Mac Pro (mid 2012)! Mac Pro has Internet Recovery ?

    "Regular" Recovery (from the Recovery partition on your Hard drive or your Time Machine Backup) remains available, but Internet Recovery (from firmware only) is not a feature on the silver tower Mac Pro. It is not on this list:
    Computers that can be upgraded to use OS X Internet Recovery - Apple Support
    But the basic recovery features are available if a recovery partition is available:
    OS X: About OS X Recovery - Apple Support

  • I can not access the internet through Nightly because of this message : COULD NOT FIND THE MOZZILLA RUNTIME.

    After i updated the browser i can not access the internet. Can you help me please?

    Hello LOUISE80, try a ''Clean reinstall''. This means you remove Firefox program files and then reinstall Firefox. Please follow these steps:
    '''Note:''' You might want to print these steps or view them in another browser.
    #Download the latest Desktop version of Firefox from https://www.mozilla.org/en-US/firefox/all/ and save the setup file to your computer.
    #After the download finishes, close all Firefox windows (click Exit from the Firefox or File menu).
    #Delete the Firefox installation folder, which is located in one of these locations, by default:
    #*'''Windows:'''
    #**C:\Program Files\Mozilla Firefox
    #**C:\Program Files (x86)\Mozilla Firefox
    Now, go ahead and reinstall Firefox:
    * Double-click the downloaded installation file and go through the steps of the installation wizard.
    * Once the wizard is finished, choose to directly open Firefox after clicking the Finish button.
    More information about reinstalling Firefox can be found [[Troubleshoot and diagnose Firefox problems#w_5-reinstall-firefox|here]].
    <b>WARNING:</b>Do not use a third party uninstaller as part of this process. Doing so could permanently delete your [[Profiles|Firefox profile]] data, including but not limited to, extensions, cache, cookies, bookmarks, personal settings and saved passwords. <u>These cannot be easily recovered unless they have been backed up to an external device!</u> See [[Back up and restore information in Firefox profiles]]. <!-- Starting in Firefox 31, the Firefox uninstaller no longer lets you remove user profile data.Ref: Bug 432017 and https://support.mozilla.org/kb/uninstall-firefox-from-your-computer/discuss/5279 [Fx31] Windows uninstaller will no longer offer the option to remove personal data -->
    Thank you.

Maybe you are looking for

  • How to access GSM AT Commands in J2ME?

    My aim is to check the signal strength of the GSM modem in any mobile(Nokia/sony). We have AT commands for the same 'AT+CSQ' which will give you the signal strength. Did any one knows how to send this AT command and get the responce in J2ME applicati

  • Multiple substitution Variable in Data Forms

    Hi, i have a problem with the creation of a hyperion Planning Data Form. I have created a Substituion Variable with "three" values delimited with a comma. I note that it works fine in the calculation script but i've a problem during the creation of a

  • Flexible Audit_Trail output Format in Oracle 10g

    Dear Friends , I have to configure audit_trail in oracle 10g , using "audit_trail = xml" or "audit_trail = xml,extended" or "audit_trail = os" Here I want to keep my user log in OS format not into DB format . But In the OS format I use the above opti

  • Fixed and variable cost component break up in PCA

    Hi, Is it possible to get fixed and variable cost component break up and contribution report in PCA at each product group level and lower level of node. I think this requires development. As my client requires the report to have cost break up into fi

  • Why do I get error message "Prop Bitmap DLL not loaded" when I try to print Adobe documents?

    When trying to print either images or text from Adobe format I receive the above error when using Mozilla firefox as my browser. i f I use Internet Explorer as browser I do not have any problems printing from Adobe.