I can't connect my mac to my TV with HDMI now that i have mountain lion

can someone please help me with this problem.  My TV keeps reading no signal.  I have tried changing ports on the tv but i keep getting the same message.  I didnt have this problem before i downloaded mountain lion.

What are you getting on the TV?  Are you getting a completely blank screen, or are you getting a message similar to 'no input detected'?  Or are you seeing the spiral galaxy desktop?  If you go into System Preferences -> Displays then do you have an 'Arrangements' tab?

Similar Messages

  • Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.

    Hi!
    Didn't know exactly where to direct this question in the Apple Community so I chose Airport.  To everyone, thanks in advance.
    I’m really desperate. I’m a big Apple fan.  I have two Apple MacBook Pro laptops with Mountain Lion software.  I also have an Apple Airport Extreme.  My HP Photosmart C4780 printer was also purchased from Apple.  Anyway, my Internet service is AT&T.  AT&T just upgraded my service with a new modem/router (AT&T U-Verse).  Prior to the conversion, my wireless printer connection was working perfectly.
    Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed.  Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works.  Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
    This appears to be an HP printer problem.  I went to HP community support with the information below but I have received no solutions outside of buying a new printer.
    “Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly.  The Diagnostic Summary in brief:  Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran.  Under Configuration Summary:  It shows old SSID name and Mac Hardware Address but no IP Address.
    Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless.  It shows status – disconnected.  Under general information it states the following: Network status  - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0.”
    To be straightforward, I’m no computer tech so I don’t know what this means or where to find.  The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve tried everything to reconfigure without success. If I need to make these changes via Airport Extreme Utility 6.0 not easy to find not that I know what I’m doing.
    Most importantly if I ever get wireless working again, do I still need Airport Extreme connection or is the AT&T U-Verse modem/router sufficient?
    Any direction or help is greatly appreciated.  Thank you for listening.

    Thank you for your prompt response.  I'll be honest I'm a retiree and a newbie to all of this stuff. I don't even know how to do a thread. (Embarassing) This is my first ever contact with the Apple Community so I'm slowly trying to figure this out as well. 
    As to your thread request, I'm assuming you want to read my post with HP.  Not knowing how to thread, I've copied it below.
    I have an Apple MacBook Pro laptop with Mountain Lion software.  I also have an Apple Airport Extreme.  My Internet service is AT&T.  AT&T just upgraded my service with a new modem/router (AT&T U-Verse).  Prior to the conversion, my wireless printer connection was working perfectly.
    Now can’t print wirelessly.  For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed.  Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works.  Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
    Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly.  The Diagnostic Summary in brief:  Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail.  Nothing else under diagnostic summary ran.  Under Configuration Summary:  It shows old SSID name and Mac Hardware Address but no IP Address.
    Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless.  It shows status – disconnected.  Under general information it states the following: Network status  - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0
    To be honest, don’t know what this means or where to find.  The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve read your forum and tried everything to reconfigure without success. Any direction or help is greatly appreciated.
    Thanks in advance!
    Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX  10.8.2 Mountain Lion.              
    I finally figured it out! (Sorry that I'm replying to my own posts btw, but I want to post the solution for anybody else with the SigmaplusEOL1 problem). If you have the SigmaplusEOL1 as your SSID when you  print the "Wireless Network Test Report", you do NOT need to return it (I know that's hassle for people).  To fix the problem, follow these steps.
    1) Unplug your printer.
    2) Go to your router's IP address (like 192.168.1.1 or whatever it is for your router).
    3) Change the SSID of your wirelss network to "SigmaplusEOL1".
    4) For the Security option for your wireless network select none (so that a password is not required to access your wireless network).
    5) Power your printer back on and reprint "Wireless Network Test Repor". It should say "No problem found..."
    6) The report should also have a the IP Address of the printer (under Configuration Summary at the bottom). Type that IP Address in your browser to get to the printer's settings page.
    7) Click the "Network" Tab at the top.
    8) Under the "Connections" header in the left pane, click "Wireless (802.11).
    9) Click "Start Wizard" at the bottom right.
    10) In the wizard, change the SSID and encryption (wep or wpsk) password to whatever you want your wireless network to be. So probably whatever it started out as before you changed the SSID to SigmaplusEOL1
    11) Click "Finish" at the end. The page will probably try to keep loading but it won't because you changed the network settings of the printer. Just ignore that
    12) Go back to your router's IP address and change the SSID and encryption password to whatever you changed the printer's SSID and password to.
    13). Reprint the Wireless Network Test Report. It should say the SSID is the same as your wireless, and everything is good.
    That's it. You should be good to go now.
    Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX  10.8.2 Mountain Lion.              
    Thank you for your prompt response.  This has been a totally frustrating experience.  I’ve spent at least 8 hours trying to fix this.  My HP problems and your initial steps were identical to mine.  I am by no means a tech person and my computer tech knowledge is minimal.  However I followed your steps to the best of my ability.
    I did get the SigmaplusEOL1 message.  I was able to get to Step 6 where the wireless network test report now reads – “HP printer settings do not match your wireless router settings.”  So I guess this is a step in the right direction.  However unfortunately the Configuration summary message for the IP Address reads – “Not Applicable”.  (Note: changing SigmaplusEOL1 to network name knocked out my Internet access.  Had to switch back to regular network name to regain access.)
    I’m at a loss as to what to do next.   Without the IP Address is it possible to move forward?  As I stated earlier, I’m not a tech person.  As to your steps 7, 8 and 9, I can’t find them on my computer or maybe I’m looking in the wrong places.  In System Preferences - Network, I have none of these steps.  If you’re referring to Airport Utility, with the changes in Mountain Lion, these steps are no longer there. If you’re talking about Safari, Firefox or HP, now I’m really lost.
    Finally, I don’t know if you can answer this or not.  If I ever get wireless working, do I still need Airport Extreme or is the AT&T U-Verse modem/router sufficient?
    Again thank you for your time and patience.
    Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX  10.8.2 Mountain Lion.                  
    Unfortunately I am unable to offer any further advice as I only followed the instructions listed on the other page.
    Finally, as to having WEP enabled, I don't know.  Don't even know where to look.  The best that I could determine is that my security is WPA/WPA2 Personal.
    I'm truly sorry about all of this.  Thank you for your time and patience.  After reading all of this and you change your mind, I would understand.

  • Can someone tell me why Apple cannot produce a Scabble game that works on Mountain Lion. So frustrated that this is not happening with all the technology available.

    Can someone tell me why Apple cannot produce a Scabble game that works on Mountain Lion. So frustrated that this is not happening with all the technology available.

    The only companies that can make a Scrabble game are the companies that own the rights to the game; Hasbro owns the rights in the US & Canada, Mattel owns the rights outside of the US & Canada.
    You need to be speaking to those two companies.

  • I can't connect MacbookPro to Infocus projector IN32IN34 (with USB). Do you have any suggestions?

    I can't connect MacbookPro to Infocus projector IN32 IN34 (with USB).
    Does anyone have any suggestions?
    Thank you!

    Which problems do you have on that website?
    Clear the cache and the cookies from sites that cause problems.
    "Clear the Cache":
    * Tools > Options > Advanced > Network > Offline Storage (Cache): "Clear Now"
    "Remove Cookies" from sites causing problems:
    * Tools > Options > Privacy > Cookies: "Show Cookies"
    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
    * Don't make any changes on the Safe mode start window.
    * https://support.mozilla.com/kb/Safe+Mode
    * https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes

  • Downloaded Cisco Connect for E1200 v2 disk image damaged. Now what? recent Mountain Lion upgrade

    I had originally set up my E1200 Jan 2012 & had Cisco Connect setup. I didn't use it much but back in Oct after being away for 10 days I didn't have internet connection. Had to re-set both cable modem--then I at least had connection via ethernet, but still no wifi connection.  Had to turn off for awhile to get it Router to properly reset & work. & then I think I had to do another reset maybe in Dec, can't remember exactly.
    As I mention in another post, I have been having frequent intermittent not connected to internet messages for a long time. Usually if I just turn wifi off & then turn it back on it finds my network (although frequently I notice that it was on my guest network rather than main). I still don't know if it is cable modem, router or my ISP, altho they came out & checked & said signals ok, but modem could be going (Its old but about to move so don't want to buy new modem now).
    I updated to Mountain Lion about 2-3 weeks ago.
    After a Panic last night I was advised to make sure everything updated including router firmware.
    When I opened Cisco Connect it said I had an unsupported Operating System. Trying to figure this all out, I finally found links to download Cisco Connect that are supposed to be compatible w Mountain Lion (at least the original link said that, but not where I went w the links so hoping it is right link for that). Anyway I downloaded it & was reading a bit & then clicket on the setup icon.
    That said it was damaged & to eject it. I downloaded it via wifi just like I download other software. Maybe it is hyper sensitive so I need to take it over to plug directly into my cable modem? But then that will mess up the router, although I guess it will need to be reset any way.
    So I think i need to get Cisco Connect updated so it works w Mountain Lion. Mountain Lion told me about 1 software that wasn't compatible but didn't pick up on Cisco Connect.
    So don't know if I need to do a hard wired download, unlike the way I download other things, or what to get an undamaged copy. I then hope that it will see the old version, even though it isn't didn't work & hopefully pick up all my settings & all.
    & then I guess I still need to check for a firmware update. & I understand that a firmware update should be done w a good connection (although the user manual just says good signal, web says hard wired ethernet. & because of the intermittent issues I plan to to it manually by 1st downloading & then installing from the download so there won't be a risk of interruption during install--if its even needed.
    I'm running on a mid April 2010 13" MacBookPro
    Any suggestions? This all is rather confusing.
    Kathi

    Well I was trying to update Cisco Connect so it would work w Mountain Lion but after 3 tries at the download I kept getting this same error message that it is downloaded. I even shut down & restarted before the last time w same result.
    I should not have to spend hours of my time to get this to work. That is ridiculous.
    Right before starting this process I checked for Apple updates & found a firmware update for my MacBookPro. I quickly downloaded & installed it, no problem. It took a very few minutes & then I backed it up & started working on this many hours ago.
    I am an end user--not an IT professional. I just want things to work. I should not be expected to have to spend hours trying to figure out how to get stuff to work & still it doesn't. So I guess Linksys doesn't care that much about making things easy for Mac users.
    I recently had the cable co come out & check the levels & all. they all checked out ok & they did change the fittings in several places on the coax connecters for good measure.
    My cable modem is set up just across my living room from me & it is not a large living room. The router is right next to it, but it is not at a desk or place that is very comfortable to set up my Mac.
    I sure hope that those security settings have been set up by default when I orginally set this up about a year ago. & I don't reall know how to change those settings without Cisco Connect, which I have been unable to get reinstalled since i keep getting those warnings about it being damaged.
    I just want my computer devices to work. I don't want to have to spend hours troubleshooting them w poorly written instructions that don't really tell how to update firmware & Cisco Connect for tnose of us who have already had it set up before upgrading to Mountain Lion.
    Having a link to download Cisco Connect that supposedly works w Mountain Lion but doesn't since it keeps giving a warning is not very helpful. There was nothing I saw in all my searches to tell what the results of even being able to upgrade Cisco Connect. Would it be able to figure existing settings? Didn't see anything that explained how that would work.
    I don't appreciate my time being stolen by making it so hard to just get this updated! I"m giving up on this. I may try taking it back to Best Buy to see if they can tell if the router itself was also defective but I think I will likely go get an airport Express so I have a reliable router that is easy to use!
    Kathi

  • Can the new Macbook Air and Macbook Pro with retina display that run OS X Lion or Mountain Lion run Windows through bootcamp?

    I was just wondering.. since the new macs have omitted the optical disk drives is it still possible to install windows on a mac running OSX Lion and Mountain Lion?

    Yes. Read the Boot Camp Install instructions for the MacBook Air which also does not have an optical drive. Put Windows onto a thumb drive or external optical drive and make these bootable. Then follow the instructions for installation from the thumb drive or external optical drive.
    http://www.apple.com/support/bootcamp/

  • Mac on 10.5 can't connect to Mac running 10.7 with firewall on

    I have a PowerPC Quad G5 tower running  Leopard (10.5.8), and a Macbook Pro running 10.7.2 Lion.
    The Macbook is my main computer. The old tower needs to be able to read files from my shared folder on the Macbook. I have made sure File Sharing is enabled on my Macbook, and AFP File Sharing shows as enabled in the Macbook's firewall control.
    If I turn off the Macbook's firewall, the G5 can connect. When the firewall is active, as I need it to be, my other Mac can ping it, and it shows in the Network list, but it never connects.
    What do I need to configure in the Macbook's firewall to allow my G5 to connect?
    Thanks.
    Paul

    Thank you for replying.
    The answer given by William in that link doesn't seem to work in my situation.  Lion doesn't appear to have an "allow all incoming" option. It has a "block all" option, which warns me file sharing won't work if I activate it.  File sharing is specifically listed as allowed.
    It seems that to  "allow all" in Lion my only option is to shut the firewall off, which is not a viable option for me.
    I can still get into shared files on the G5 from the Macbook, no problem. It's the other direction that is a problem.
    Paul

  • How can I connect a Mac book pro to an hdmi connection on my TV

    Trying to watch movies from my MacBookPro on my LG TV w an HDMI connection. What cables and or additional SW do I need?

    You'd have better luck if you posted this in the appropriate forums.
    https://discussions.apple.com/community/notebooks/macbook_pro
    B-rock

  • HT1454 Can I connect my iPad to my tv with HDMI ?

    Can anyone tell me if I can connect my iPad 3 to my home tv using HDMI connection

    Connect to TV in two ways.
    1. Apple Digital AV adapter+HDMI cable
    http://store.apple.com/sg/product/MD098ZM/A/apple-digital-av-adapter
    2. Apple TV
    http://store.apple.com/sg/browse/home/shop_ipod/family/apple_tv?afid=p219%7CGOSG &cid=AOS-SG-KWG

  • Why can't I see the video icon in phone booth now that I upgraded to lion

    I upgraded my mac to Lion and can no longer make videos in phonebooth only the camera icon is available.

    There is no rotate icon in the Photos App. I don't have one on the iPad original and I'm running iOS 4.3.3. There will be in iOS 5 I think but it is not an available feature currently. There are third party apps that let you rotate, crop and edit but not the Photos App.

  • HT201304 Why can I not make purchases on casino now that I have installed iso7

    Why can I not make a purchase on the game casino now that I have installed iso7?  I can make purchases in other apps

    I'm having this problem on my iPhone and iPad when trying to purchase

  • How can I connect my Mac Book Pro (year 2008) to the TV set through  HDMI? I've seen a DVI to HDMI iwire but I'm no sure that it is correct. Could anyone help me? Thank you very much.

    How can I connect my Mac Book Pro (year 2008) to the TV set through  HDMI? I've seen a DVI to HDMI iwire but I'm no sure that it is correct. Could anyone help me? Thank you very much.

    I do not know the iWire adapter, but I use an inexpensive ($3) DVI to HDMI adapter from Monoprice, along with a regular HDMI cable:
    http://www.monoprice.com/products/product.asp?c_id=104&cp_id=10419&cs_id=1041902 &p_id=2029&seq=1&format=2
    Be aware that this will only transfer video. You Macbook Pro cannot combine audio through DVI to HDMI. You will need to listen to the audio through the Mac speakers, or attach speakers or a sound system to the Mac earphone jack, or determine if your TV has the ability to accept external sound from the Mac while showing video through HDMI (few can).

  • How can i connect my mac book pro with retina display 2014 Mid to 5.1 channel? what is the connector am i to use? i wonder if anybody could probably let me know?

    how can i connect my mac book pro with retina display 2014 Mid to 5.1 channel? what is the connector am i to use? i wonder if anybody could probably let me know?

    https://www.youtube.com/watch?v=72l_FLsXNAg
    I use Hercules found here http://www.hercules.com/us/Sound-Cards/bdd/p/123/gamesurround-muse-xl-pocket-lt3 /
    also read this helpful thread Outputting 5.1 Channel Surround Sound from your Mac

  • I would like to know how i can share my music using an UPnp protocole. I have an Imac but when i'm chosing the option share my file i can connect my mac to another network reader . it seems that the protocole used is not UPnp. I need this to be in UPnp.

    I would like to know how i can share my music using an UPnp protocole. I have an Imac but when i'm chosing the option share my file i can connect my mac to another network reader . it seems that the protocole used is not UPnp. I need this to be in UPnp. does somebody can help ?

    Google "upnp mac"

  • I can't connect my mac to my TV, I have the right cables and have done it right but I still doesn't get the macscreen on the Tv, what should I do?

    I can't connect my mac to my TV, I have the right cables and have done it right but I still doesn't get the macscreen on the Tv, what should I do?

    What are you getting on the TV?  Are you getting a completely blank screen, or are you getting a message similar to 'no input detected'?  Or are you seeing the spiral galaxy desktop?  If you go into System Preferences -> Displays then do you have an 'Arrangements' tab?

Maybe you are looking for