I can't get the metronome figured out

even when I uncheck it, it keeps clicking away!
it's driving me nuts!

did you accidentally record it?

Similar Messages

How can I get the metronome to click dotted-quarters in 6/8?

When I go from 4/4 to 6/8 the metronome goes hyper (clicks 8ths)
This is annoying. How can I get the metronome to lay back and click dotted-quarters instead?
-Thanks

Working in 3/4 is not a realistic alternative to working in 6/8. Fundamentally, 3/4 and 6/8 are not the same thing at all. Basic music theory 101, yes?
If you want to work with a dot-quarter click, set your time sig to 6/8 as you normally would. Then create your own click track by assigning the Klopfgeist to a track and recording (or penciling in) two dot quarters. One measure will do. Quantize and loop that region. You're done!
\[EDIT] You might want to play around with the pitches and velocities of those two notes, but once you learn which notes (and velocities) sound best you're totally good to go.
This technique (creating your own custom click track) is also useful if you wanted to work in 6/8 but alternate between 6/8 and 3/4 feel. There's an traditional Argentine rhythm (Chacarera) that uses this (thanks Jordito for the reminder of what it's called). There are other examples as well. Anyway, 6/8 is not 2/4 or 3/4. It's 6/8, just like 12/8 is not 4/4, and 9/8 isn't 3/4. My main point is that you shouldn't have to compromise in terms of editing on the grid or anything else just because Logic doesn't give you the click you need out-of-the-box. Work MUSICALLY and get Logic to bend to your will by using the technique above. Or, the one below!
Message was edited by: iSchwartz

I purchased an ablum thru itunes on my phone and it says i purchased the songs on itunes but when i go on my music it says i have to repurchase all the songs how can i get the songs with out havin to pay again

I purchased an ablum thru itunes on my phone and it says i purchased the songs on itunes but when i go on my music it says i have to repurchase all the songs how can i get the songs with out havin to pay again

Whether you can redownload music depends upon what country that you in. If you are using your computer's iTunes then does music show in the Purchased link under Quicklinks on the right-hand side of the iTunes store home page (on your phone you might be able to redownload media via the Purchased tab in the iTunes store app) ? If music shows there, but not that album, then check to see if it's hidden : http://support.apple.com/kb/HT4919
If you aren't in a country when you can redownload music and it's still on your phone then you should be able to copy it over from the phone via File > Devices > Transfer Purchases.

Oj4632 I can't get the paper device out of my new printer? locked in somehow.

oj4632 I can't get the paper device out of my new printer? locked in somehow. very frustratied

Set the System property "mail.mime.decodeparameters" to "true" to enable the RFC 2231 support.
See the javadocs for the javax.mail.internet package for the list of properties.
Yes, the FAQ entry should contain those details as well.

Can't get the attachment filename out of a Part (with non ascii characters)

Hello, all and happy new year :)
My issue is with non ascii filename in attachments... Yes i've read the FAQ : http://www.oracle.com/technetwork/java/faq-135477.html#encodefilename
I can't get the filename out of the BodyPart for those kind of attachments
here's my unit test :
     * contains various parts from various mailer encoded in different ways...
     private enum EncodedFileNamePart{
          OUTLOOK("Content-Type: text/plain;\n name=\"=?iso-8859-1?Q?c'estd=E9j=E0no=EBl=E7ac'estcool.txt?=\" \nContent-Transfer-Encoding: 7bit\nContent-Disposition: attachment;\n filename=\"=?iso-8859-1?Q?c'estd=E9j=E0no=EBl=E7ac'estcool.txt?=\" \n\nnoel 2010\n","c'estdéjànoëlçac'estcool.txt"),
          GMAIL("Content-Type: text/plain; charset=US-ASCII; name=\"=?ISO-8859-1?B?ZOlq4G5v62znYWNlc3Rjb29sLnR4dA==?=\"\nContent-Disposition: attachment; filename=\"=?ISO-8859-1?B?ZOlq4G5v62znYWNlc3Rjb29sLnR4dA==?=\"\nContent-Transfer-Encoding: base64\nX-Attachment-Id: f_giityr5r0\n\namluZ2xlIGJlbGxzIQo=\n","déjànoëlçacestcool.txt"),
          THUNDERBIRD("Content-Type: text/plain;\n name=\"=?ISO-8859-1?Q?d=E9j=E0no=EBl=E7acestcool=2Etxt?=\"\nContent-Transfer-Encoding: 7bit\nContent-Disposition: attachment;\n filename*0*=ISO-8859-1''%64%E9%6A%E0%6E%6F%EB%6C%E7%61%63%65%73%74%63%6F;\n filename*1*=%6F%6C%2E%74%78%74\n\njingle bells!\n","déjànoëlçacestcool.txt"),
          EVOLUTION("Content-Disposition: attachment; filename*=ISO-8859-1''d%E9j%E0no%EBl.txt\nContent-Type: text/plain; name*=ISO-8859-1''d%E9j%E0no%EBl.txt; charset=\"UTF-8\" \nContent-Transfer-Encoding: 7bit\n\njingle bells\n","déjànoël.txt"),
          String content=null;
          String target=null;
          private EncodedFileNamePart(String content,String target){
               this.content=content;
               this.target=target;
          public Part get(){
               try{
               ByteArrayInputStream bis = new ByteArrayInputStream(this.content.getBytes());
               Part part = new MimeBodyPart(bis);
               bis.close();
               return part;
               catch(Throwable e){
                    return null;
          public String getTarget(){
               return this.target;
     @Test
     public void testJavamailDecode() throws MessagingException, UnsupportedEncodingException{
          System.setProperty("mail.mime.encodefilename", "true");
          System.setProperty("mail.mime.decodefilename", "true");
          for(EncodedFileNamePart part : EncodedFileNamePart.values())
               assertEquals(part.name(),MimeUtility.decodeText(part.get().getFileName()),part.getTarget());
I take a NullPointerExcepion in the decodeText because getFileName() return null for the EVOLUTION case, and work well with OUTLOOK, THUNDERBIRD and GMAIL.
Evolution's content type is "Content-Disposition: attachment; filename*=ISO-8859-1''d%E9j%E0no%EBl.txt" wich doesn't look like the other (looks like the RFC 2616 or RFC5987 to do it.)
How can i handle this situation except by writting my own decoder?
Thanks for your answers!
Edited by: user13619058 on 4 janv. 2011 07:44

Set the System property "mail.mime.decodeparameters" to "true" to enable the RFC 2231 support.
See the javadocs for the javax.mail.internet package for the list of properties.
Yes, the FAQ entry should contain those details as well.

I can not get the right frequency out of my NI-DAQ 6062E card from Matlab

Hi.
My name is Johan and I want to generate an analog square waveform with 5.76 kb/s in frequency with my NI DAQCard-6062E from Matlab.
When I run in Matlab the program below, I get the frequency of 5.747 kb/s on the output channel (even thou I have chosen 5.76 kb/s). When I try to change the sample rate, to higher values in Matlab, I get the same frequency until I choose the sample rate to 5.79 kb/s. The output signal is in that case is 5.813 kb/s.
So my problem is that I can't get the exact frequency of 5.76 kb/s.
How do I solve this.
Thankful for help.
Best regards, Johan
Program in Matlab:
clear all
openDAQ=daqfind; %Detect any open DAQ channels
for i=1:length(openDAQ), %Close any open DAQ channels
stop(openDAQ(i));
end
ao = analogoutput('nidaq',1); %Create an object for analog output
addchannel(ao, [0 1]);
set(ao, 'SampleRate', 2*5760); %Here the sample rate is specied. 2*, because to get right samplerate
y=[80,-80] %Sets theoutput values to 80 and -80 (As -1 and 1)
putdata(ao, [y' y']); %Sends the values to out buffer
set(ao,'RepeatOutput',inf) %Repeats sending in infinity
set(ao, 'TriggerType', 'Immediate'); %Choose trigger to immediate, because sending values shall occur driect after start command.
start(ao);
%stop(ao)

Hello Johan!
Bad news I am afraid….
I assume you are using the Data Acquisition Toolbox from the Mathworks and when it comes to support on that interface I have to advice you to contact the Mathworks for assistance. We don't provide any support on their data acquisition interface since we have nothing to do with it.
Sorry for the inconvenience this might cause you.
Regards,
Jimmie A.
Applications Engineer, National Instruments
Regards,
Jimmie Adolph
Systems Engineer Manager, National Instruments Northern Region
Bring Me The Horizon - Sempiternal

I can't get the old account out my update

I can not get the old account off even if I sign in on my new account the old still show up and I can't update how do I get the old one out my iPad I tried signing out and in, my new account is in but when I try to update something an old account pops up and I can't do anything

Settings > iTunes and App Store > Apple ID = Sign Out... Then Sign In using the preferred Apple ID.
Dinky710 wrote:
... but when I try to update something an old account pops up ...
Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID

How can I get the third battery out of the wireless keyboard to change it?

I got a message to change the batteries in my keyboard, but only two batteries will come out. Is there a way to get the third one out?

turn your keyboard over-there should be a diagram telling you how many batteries
it takes (2 or 3). If you do have a 3 battery keyboard, perhaps a little wiggling or tapping may help, or a little wd-40, maybe a chopstick?
JB

Can't get email to figure out answer to security questions which I can't remember

I keep trying to get the link to having an email sent to me so that I can figure out my security questions for my apple id. But I still have not received one. Also says that I've never signed in using this computer which isn't true. Not even sure why I'm having trouble. Just wanted to purchase an album for my ipod.

No Apple staff here, ever. Only users.
See this: http://appletoolbox.com/2012/07/how-to-change-the-answers-to-the-security-questi ons-for-apple-id/

Can't get the Toslink (Optical) out to work with Airport Express

I have the monster cable hooked up but get no optical out. I hooked up the mini plug to RCA and that works but the optical doesn't. Is there a setting I'm missing. I know the cable is working because I hooked it up to my mini computer and get the red light coming out the end. I don't get any light from the airport expess mini plug to Toslink.

Same problem here. Just bought an optical cable with the mini toslink connector (to work with the express and computers). I can get audio if I connect the cable to my computer, but no audio from the express. Regular analog audio comes out fine, but I cannot get the optical to work.
I can't find any preference or setting to change and have tried resetting the base station. Anyone have an idea?
iMac G5 Mac OS X (10.4.8)

Hello, I can`t get the DVD back out of my iMac. What can I do?

Hello, there is a DVD loaded in my Imac, but I can`t get it obviously out on the normal way. Is there anything i can do?
Thanks for your comments.

A few other possibilities here: http://osxdaily.com/2009/08/28/eject-a-stuck-disk-from-your-mac-dvd-super-drive/

How can I get the DC component out of a signal in Labview

I was trying to get the DC component of a signal using lowpass filters provided by Labview(professional version 8.2). I used the FIR windowed filter but I couldn't get what I expected. The sample rate is 20* the maxium signal frequency. I simulated a function like y= 10(volt)+Sin(2*pi*f*t+phase). If I set the low cutoff to be less than the frequency f, shouldn't I get 10 volt as the outputs? See the attachment for vi. Thanks!
Attachments:
Simulation03062008.vi ‏53 KB

Hi,
You can use the filters located in Signal Processing -> Filters, then create a constant from the "filter type" input and select "Lowpass". There is also an AC & DC estimator vi, located in: Signal Processing -> Measurement.
You may also use something like "running mean" filter. To do it you need to calculate the mean value in some range around every point. It will decrease the value of the noise and will give you the dc value (or slow changing part) of your signal. Finally you can use median filter.
Benjamin R.
R&D Software Development Manager
http://www.fluigent.com/
Attachments:
meanrun.vi ‏21 KB

Itunes Internet Radio. Can I get the URL's out to stream on other units?

I just purchased a SONOS music system. I would like to take some of my itunes internet Radio stations and play on my sonos. I just can't find the URL's for the stations. is there a way to get this info?

Thanks very much I have contacted them via this. Just hope they respond quickly- rather annoing! Greatly appreciated though

How can I get the POST data out of a quiz?

Trying to get data out of a quiz with PHP or ASP. How? Do I
have to set up the Quiz Output to something in particular? I want
to get the $_POST['correct'] information out --or
Request.Form("correct"). How do I do it?

This thread is cross posted. Please review the
Posting
Guidelines for more information on why this is a bad thing.
Click
here to view the original thread

How can I transfer The Simpsons Tapped Out game from my iPhone 4 to my iPhone 5?

I have just gotten an iphone5 and have done a backup from my iPhone 4.
I can't get The Simpsons Tapped Out existing game to work on the iPhone 5, how can I get the original game to work on the new phone? As I've done the restore on the new phone, it brings up a whole new game to start up with again.

i have tried to do this but when i log in it tells me there is a level 4 game on this device not my level 25 game. any suggestions

I can't get the metronome figured out

Similar Messages

Maybe you are looking for