I can´t reset with 648 max

I have a motherboard 648 max.
1 DDR 512 MB 400 MHZ
1 HD 120 GB Ide
1 Ati Radeon 9100
Problem is can´t reset my computer , when it initiates my monitor it remains if signal and leds power y hd ignitions.
I have to unplug behind source feeding and to return to connect it.
They can say the solution to me?
The bios have defaults settings.

Where do the D-Bracket LEDs stop? The 648Max has a lot of problems with DDR400. Also needs a strong PSU. Go through some of the older posts. You'll find a plethora of information.
Do a search for 648Max.

Similar Messages

SiS AGP drivers with 648 MAX-F and TI-4600 GS

A few days ago I bought a new computer. Here are the specs:
Compucas 6A21B 300W SuperLowNoise
Intel Pentium 4 Northwood 2,4GHz
MSI 648 MAX-F
Kingston 512Mb 333Mhz DDR
Seagate Barracuda ATA V 80Gt 7200rpm
Gainward Geforce4 Ti4600 ultra/750 XP golden sample
windows 2000
I have tried everything to get the SiS AGP drivers work. Every time I start with them I get a white screen with colourful horizontal lines. There is also gray at the bottom of my screen. This picture comes after the windows screen, when it should say preparing network connections and everything. I have service pack 3 and DirectX 9. I have tried many different versions of the drivers from both MSI and Gainward/NVidia. I even upgraded my BIOS. From bios I have tried all the DRAM timing things. Now I have a nice set of drivers on my computer. Is there anything else to do than wait for new drivers? It works fine after I uninstall the AGP drivers. Does the operating system matter?

Did you try the newest drivers from Nvidia's website?
Did you try video card in another system when you had it in the shop, and another video card in your system? I take it you did a clean install of Windows XP. Mine has had no problems in WindowsXP, It's a Chaintech Ti4600. While I do have Windows 2000, I haven't used it on this system so I'm no help there. Also did you try setting BIOS to default settings? Come to think of it, I think it defaults to graphics card in PCI slot, maybe I'm thinking of another board. Don't know if that would make a difference anyway. Can you go into safemode and update or remove the agp drivers and start over? Is this fun or what? Did the AGP drivers you installed, create a Sis agp utility folder in the start menu? That might give you some information about any possible problems. What are the agp voltage readings in the BIOS?
Oops! Checked my BIOS, there is no setting for graphics card in PCI slot. Way too many motherboards. I'd try re-installing XP from scratch, install all sis drivers, install Nvidia drivers, install XP service pack. If that doesn't work, get mad, scream and run out the front door with arms flailing!

External USB 2.0 HDD Problems with 648 Max

I'm getting I/O error and/or very slow read performance from an external Maxtor HDD when I use the rear USB ports that came with my 648 Max. When I use the front ports on my case, I get very good read and write performance. I installed a firewire card and it also works very well. Why can't I use the ports that are connected to the motherboard?

ok i dont have the manual with me to make sure if this is correct or not but you can check yours.
i know that alot of the newer motherboards have a mixture of 1.1 usb and 2.0 so it is possable that the msi 648 is the same (again look at your manual) and if so you might be hooking it up to your 1.1 port whereas your case usb is hooked to your 2.0 usb ports.
this is just a guess but it is worth checking out in your manual. hope this helps.

Wierd issues with 648 MAX-L

I recently put a system together with the 648 Max-L mobo.
P4 2.4
Maxtor ATA133
Windows XP
1 Gig PC2700 Crucial
Radeon 9700 (non-pro)
Philips Seismic Edge (was Aureal Superquad)
Having some weird issues;
1) Occasional crashes -I ran Goldmemory tests and the ram failed.....so I am RMA'g the ram but......ran Memtest 86 and it passed! ????????? So I think maybe it's good ram and the mobo is having a compatibility issue.
2) When I turn the PC off, the drives light up! Namely the operting lights actually come on and burn steady when I turn off the PC....I have to hit the main kill switch to shut them off. Really weird.
3) Maxtor has bad sector, but I am going to do a low end format that Maxtor says will fix that.
Anyone have any ideas? Once I do everything else, the next step is to get a new mobo....but this one works good other then the above issues, and I hate to waste the $75.00 I paid for what should be a good mobo. I could get another board and RMA this one....but if it IS the board I doubt I will buy the same one.
Anyone have any similar issues or ideas?

Oh, It also is in a mid tower ATX case with a 400W Mustang power supply.

I need to reset my security questions because it says the answers I provided are not correct. How can I reset with new security questions and answers

I need to reset my security questions and answers. But nit is saying my birthday for a verification is invaid. How can I reset all of this?

You need to ask Apple to reset your security questions; ways of contacting them include clicking here and picking a method for your country, phoning AppleCare and asking for the Account Security team, and filling out and submitting this form.
(99552)

How can connect java with 3D Max

i want to make 3d maze by reading from text file
for example when i read 0, then i draw wall
when i read 1 i draw path ..and so on
and i want to move the object in the maze by using AI techniques
my questions are:
- can I read from file and draw by using 3D Max and program the
object moving using java, if yes, how can i connect the java and 3D Max
if there are any resoures, or any other silution may help me
please tell me about it

I've found two loaders to load 3ds files, so if you export your models from 3ds max that should work.
http://www.starfireresearch.com/services/java3d/inspector3ds.html
http://sourceforge.net/projects/java3dsloader/
//My hyperlink option doesn't work today
Hope it helps.
//Considerate

Problem UDMA6 with 648 Max

My PC :
Pentium 4 2,4 Ghz + 256 Mo Pc 2700
Windows 2000 SP3
1 hd Maxtor 60Go ( IDE 1)
1 DVD + 1 CDWR ( IDE 2)
Windows refuse to switch the hard drive in UMDA 133 ( mode 6 ) and stay in PIO.
but my CDs switch in DMA and UDMA 2. why ??
I flashed my Bios ( V1.3) but it's the same.
my SiS IDE driver is : v2.2.1.0
thanks...

You should not run a slower device on the same IDE channel, move the CD ROM over to the secondary IDE channel and you should notice a difference. )
Keep your hard drive(s) on primary IDE, and place CD ROMS, DVD/CDRW's on the secondary channel.
If you run a number of drives you want a reliable p/s-350W+ for higher end graphic cards-hd, etc.
Also check PIO/UDMA setting in BIOS...Default is AUTO, etc.
P4 2.26 768MB DDR 2700
2) 80MB Maxtor ATA133/7200 HD's (non-raid)
GF4 TI-4400 128MB
MSI 645DX v 1.0
Audigy 2 Sound

Forgot password how can I reset with a new password?

Changed my Apple ID now I cannot use ICloud how do I set new password ??

https://iforgot.apple.com/password/verify/appleid

648 max , testing base and extended memory

I dont see the thread i answered to one time that someone spoke of using ddr400 with 648 max or max-L board and they were getting testing base and extended memory error from the LED's. Well i just got the same error today and my system would not boot i cut the power to the PS. and turned it back on it would start to boot and hang i could barely get to the windows logo sometimes the vid card wouldnt even boot the logo to the screen. This is with an updated mobo that msi sent me that i had just put in , it seemed to run fine at first then this problem started occuring. The only difference i had in the setup from the previous outdated board was i had the mem in DIMM 3 and not DIMM 1, so i moved the memory back over to DIMM 3 and now the problem is gone. Just something for those of you with the same problem to try.
Oh and i forgot one more issue, i cannot set the dram speed in the bios manually i have ddr 333 it should be 167 mhz so i set it to 4/5 and the system will not boot at all i end up having to reset cmos. I called MSI about that and they told me to just have it set to SPD , I said i know that and im fine with leaving it that way but it should let me set it manually if i wanted to and that i wondered if that had anything to do with the random " testing base and extended memory " problem.

It was probably myt thread...
http://www.msi.com.tw/program/e_service/forum/viewindex.php?threadid=6204&boardid=10&styleid=1
Have done some testing with both DDR333 and DDR400 and my results are in the thread.
Right no I'm using my DDR400 as DDR333, manually set to 167MHz, using DIMM1, and havn't seen any problems. I'll try the DIMM3 to see if I get any changes.
And by the way.. I tried setting my DDR400 manually to 200MHz and it wouldn't boot at all. After a lot of ugly language I finally got it back to the BIOS....after a reset of the CMOS.
Seams like you should use SPD if you want to use the correct freq for your RAM.
Have you tested the new 1.3 BIOS?

648 max and HT

alrighty guys, im building my own computer and decided to go with 648-max because my friend has one with radeon9700 pro and 0 problems, so i thoguht id follow his line. anyways, im going to get a P4 3.06 ghz processor with hyper-threading (HT) enabled on it. now i see on MSI's mainboard page there is 2 diff 648-max's, basically one with HT support and one without. now my question is, is the HT support on that board just part of a BIOS upgrade or part of the hardware? i found 648-max's for like 80$ at places liek newegg but i cant find 0 places that specifically state it enables HT in the specs. is this new 648-max, the one with HT, replacing the older? or is it a completely separate board? if it is a different board, could someone please link me to a site selling one, i would like to check it out, thanks you much
-Brian

I have just purchased a 845PE Max with Hyper-Threading ready written all over it. It even has the label stating " Intel 845PE Hyper-Threading Technology" Well guess what? Even though my CPU (P4 2.4Ghz B), and my motherboard 845PE MAX both support Hyper-Threading you still need the BIOS that supports the Hyper-Threading. The BIOS does not come with the option to enable Hyper-Threading.The board comes with the latest BIOS update. I have written to MSI requesting the correct BIOS. I guess it's the luck of the draw? Good luck with your board!

Sound Problems with MSI 648 Max ( MS-6585 ) Board - Help !!!

Hi,
i have the MSI Mainboard: MSI 648 Max ( MS-6585 ) and when I put on the microphone i have a bad sound on my soundboxes like scratching or beeping.
I have installed a new BIOS update and new Sounddrivers.
I have Win2000 with SP3.
Anybody can help me???
THX ;(

Error404,
I since you have a 648 Max and you posted in the Multimedia Forum, I moved the thread to PIV Motherboard Forum for you.
Good Luck,
Richard

AGP 8X and Fastwrite with MX440 8X on 648 Max L

Hi,
I own the 648 Max L and I have just bought a MSI Geforce4 MX440 8X. I have SiS Agp drivers 1.15 installed and:
1. AGP 8X does not work although I can "enable" it
2. It says that the board does not support AGP Fastwrite but the graphic card does.
Can I please have some feedback on these issues thank you.
Razvan

I take it you're seeing this with the AGPUtil? I have found the same results with my mobo, but (and this is a but) I think it's just reading the info wrong. ATI SmartGart lists AGP 8x and Fastwrites working, while agputil does not.
Also, if you read the info file that came with those drivers (if you got them from MSI), certain motherboards are not compatible with the newer AGP drivers, and thus use v1.12. I've been looking for the AGPUtil that came with that version to double check, but haven't been able to find it.
[Edited] Maybe someone who has either of the two boards with the newest AGP drivers can offer their results as well...

648 max, wont boot to cd with locked HDD connected

hi i hope you can help me, i bought my son a cheap second hand PC from a car boot sale, inside which is an MSI 648 max motherboard,
the problem i have is i am trying to attach a larger hard drive which is locked, usually to unlock the HDD i run a bootable cd-rom which is fine however when i try to boot the computer i get a message stating the hard drive is locked and i have 5 attempts to enter the password.
unfortunately i do not know the password as it is encrypted on the cd-rom, if only i could boot to cd-rom this wouldn't be a problem however i can not boot to cd-rom with the locked hard drive connected and obviously i cannot connect the hard drive after its booted to cd as it will not be detected,
when i try to access the boot menu i hit F11 as stated but all i get on the POST screen is "GO-->boot menu and then it hangs on the POST screen, what does this mean?
so my question is, is it possible to boot to CD with the locked HDD connected as im getting quite frustrated,
i hope i have given enough information but if you need anymore i shall happily provide
many thanks
Glenn

If the hard drive is still servicable you can use a bootable cd or floppy to erase the contents of the hard drive.
The ultimate boot cd has numerous apps to erase hdds. http://www.ultimatebootcd.com/
Or just get another hard drive.
Could be something else wrong of course. At least the UBCD is free.

HT204266 My iPad (version 1, IOS 5.1) has quit connecting with the store. I am unable to update or buy any app. I did a reboot and a reset with deleting the data. I can not find anything in support for this problem. Any help will be appreciated.

My iPad (version 1, IOS 5.1) has quit connecting with the store. I am unable to update or buy any app. I did a reboot and a reset with deleting the data. I can not find anything in support for this problem. Any help will be appreciated.

My iPad (version 1, IOS 5.1) has quit connecting with the store. I am unable to update or buy any app. I did a reboot and a reset with deleting the data. I can not find anything in support for this problem. Any help will be appreciated.

I am having a Startup problem. Someone comes on the screen with Open Firmware to Startup. How can I reset the PRAM myself to solve this problem?

I am having a Startup problem. Someone comes on the screen with Open Firmware to Startup. How can I reset the PRAM myself to solve this problem?

Read these.
http://support.apple.com/kb/HT1431
http://reviews.cnet.com/8301-13727_7-10330118-263.html

I can´t reset with 648 max

Similar Messages

Maybe you are looking for