I cannot connect my Kindle Fire to the network. It looks for the IP address and says Cannot connect. Try again. On my iPad I see that a new client is on the network but just for the time of not finding the IP address. Any suggestion? Thank you.
The Kindle Fire finds my Wi-Fi network but cannot obtain an IP address. My iPad AirPort is telling me that a new client is on the network until the Kindle Fire says Cannot connect Try again Any suggestion? Thank you
Any chance the wifi network you're trying to connect to has had its access password changed? If so, do you have the correct password?
Can you 'rub' the wifi antenna on the iPad? That might help. I've done this with my iPod Touch and it helped restore the device's ability to connect.
Is it possible to power cycle the wifi router you're trying to connect to?
If worse comes to worse, can you 'reset' the iPad? You could do this, but I'd maybe suggest it as only a last resort.
I think you can also go into the wifi settings and 'delete' that wifi network and then re-connect to it.
Good luck with it.
Similar Messages
-
Can I transfer my CS4 license to my new laptop with a part number but no CD. I can not find the CD.
Can I transfer my CS4 license to my new laptop with a part number but no CD. I can not find the CD.
Download CS4 products
Mylenium -
Looking for a free iPod to iTunes music transfer utility, any suggestions
Looking for a FREE utility that will allow me to transfer music from my iPod to my iTunes. I recently purchased a new notebook PC that I recently download a fgresh installation of iTunes. Now I need to transfer my music stored in my iPod to iTunes. I find many free transfer utilities on the internet that allow you to only transfer a couple of songs, not your whole iPod. Any suggested freeware utilities would be appreciated.
Message was edited by: MASZR1
Message was edited by: MASZR1If you enable your iPod for disk use, you should be able to do this without utilities (unless iTunes checks for this kind of thing). See, all of your music is stored (with garbled filenames) under <D:/iPod_Control/Music/> (where "D" is your iPod). So if you use iTunes's "Add Folder to Library" on the "iPod_Control/Music" folder, it should import your iPod files.
So do this,
1. Set Windows to show hidden files and folders, if it isn't already. There are plenty of guides for this on Google.
2. Open iTunes.
3. Enable disk use on your iPod, if you haven't already.
4. Go to File > Add Folder to Library....
5. In the Open Folder dialog box, navigate to your iPod.
6. Go into the iPod_Control folder.
7. Select the Music folder. Click OK.
Note that on Windows, the iPod_Control folder (and its contents) are hidden, so you need to set Windows to show hidden files and folders. -
OSD TS looking for previous package version, not finding it.
Yesterday, I upgraded our SCCM environment from 2012 R2 to 2012 R2 CU3.
I am currently unable image most machines (only VM's work, for some reason) as the TS is failing with the error about it not being able to find the package xxx00002, which is our Configuration Manager Client package. As a part of the CU3 upgrade, it
initiated a update on this package, taking it from version 10 to version 11. All distribution points now have the version 11 package.
My pain point is that the task sequences we are attempting to reimage with are failing when looking for version 10 of the package. Snippet below. I'm hoping someone has some ideas on how I can resolve this or has seen it before. I tried
changing the package in the 'Setup Windows and Configmgr' step to another package, saving, and changing it back, to no avail.
Log snippet below.
Content location request: TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Package : XXX00002.10 TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Client : GUID:EB7523EE-E5F0-48B0-8F27-C84D21BEE0DC
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Local : 1 TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Remote : 4 TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Internet: 0 TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Sending RequestContentLocations for XXX00002
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Setting message signatures. TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Setting the authenticator. TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
CLibSMSMessageWinHttpTransport::Send: URL: servernameFQDN:80 CCM_POST /ccm_system/request
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Request was successful. TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
::DecompressBuffer(65536) TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
Decompression (zlib) succeeded: original size 244, uncompressed size 882.
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Location Reply: <ContentLocationReply SchemaVersion="1.00"><ContentInfo PackageFlags=""><ContentHashValues/></ContentInfo><Sites><Site><MPSite SiteCode="111" MasterSiteCode="111"
SiteLocality="LOCAL" IISPreferedPort="" IISSSLPreferedPort=""/><LocationRecords/></Site><Site><MPSite SiteCode="222" MasterSiteCode="222" SiteLocality="LOCAL" IISPreferedPort=""
IISSSLPreferedPort=""/><LocationRecords/></Site></Sites><RelatedContentIDs/></ContentLocationReply>
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Processing 0 locations. TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
No static content server. TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
LocationsList.size() > 0, HRESULT=80040102 (e:\qfe\nts\sms\framework\tscore\resolvesource.cpp,2138)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
FALSE, HRESULT=80040102 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,1930)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Content location request for XXX00002:10 failed. (Code 0x80040102)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
hr, HRESULT=80040102 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,2702)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Failed to resolve PackageID=䛸Dž TSPxe
1/30/2015 2:30:24 PM 1796 (0x0704)
(*iTSReference)->Resolve( pTSPolicyManager, dwResolveFlags ), HRESULT=80040102 (e:\qfe\nts\sms\framework\tscore\tspolicy.cpp,3488)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
m_pSelectedTaskSequence->Resolve( m_pPolicyManager, TS::Policy::TaskSequence::ResolvePolicy | TS::Policy::TaskSequence::ResolveSource, fpCallbackProc, pv, hCancelEvent), HRESULT=80040102 (e:\nts_sccm_release\sms\client\tasksequence\tsmbootstrap\tsmediawizardcontrol.cpp,1564)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Failed to resolve selected task sequence dependencies. Code(0x80040102)
TSPxe 1/30/2015 2:30:24 PM
1796 (0x0704)
Thanks in advance!
ScotYes. They have version 11.
In the meantime, I have created a new Configuration Manager Client package and swapped it out with successful results, as might be obvious.
Most likely, I'll simply update the package on the distribution points to resolve it permanently (to version 12). It's just not a quick fix for us as we have
a lot of distribution points. Sending down another copy, since the files are already there in content library, won't require nearly as much WAN traffic or time. We'll swap the task sequences back once
we update XXX00002 to version 12.
Thanks,
Scot -
I'm looking for a pro or semi pro cabinet layout software any suggestions?
I am a remodel contractor. I previously had PC's in the office and have converted to Mac. I cannot find decent cabinet layout software that is also Mac compatable. Any suggestions?
There are no layout programs, specifically, designed for OS X to deal with just kitchen cabinet layout work.
There are a few interior layout programs both 2D/3D as well as straight CAD type programs for doing both 2D and/or 3D layout work.
Here's a short list of all the top CAD programs for Mac OS X
http://blog.dreamcss.com/design-tool/cad-software-for-mac/
Here's another source for design apps
http://www.pure-mac.com/cad.html
This last link, I believe, covers all of the technical design software available for Mac and Mac OS X.
Here's another I found.
http://icadmac.us/home
Good luck! -
Directv Apt will not connect to the receiver. The receiver is connected to the internet. All other functions work fine
have you went to the DirectV support site? They sem to have a lot of information there for mobile productes.
-
GoFlex, Xfinity, & Time Machine not working together anymore. Any suggestions?
I have a GoFlex external harddrive connected to an Xfinity wireless modem. For over a year I was able to successfully back up (Time Machine) on two MacBook Pro. About 4 months ago, Time Machine would not complete the back up on either computer. After powering down all related devices and repowering everythign works consistently until the Time Machine back up starts. The back up will start and continue for 20 minutes. After 20 minutes the back up stops and the Xfintiy Modem stops wireless tramission. I have researched and attempted several different methods to resolve, but with no success.
Has anyone else had this problem and found a solution?I am of no help to you... but maybe you can help me.
I can't get Time Machine to work with my GoFlex Home. I know it's not my wireless network. Because I've gone through a dsl modem/wifi by NetGear. Then a NetGear 2.4/5.0GHz wifi router and now Airport Extreme 5th gen.
TM recognize GoFlex Home as an acceptable disc for TM. But after a few seconds of trying to connect to it, it fails. I forget the exact reason though.
How did you connect to the GoFlex as a Time Machine?
KOT -
I have a new IMAC with lion. When I use the migration tool from my PC to the new Mac, it takes about 2 hours to transfer my photos and address book, etc. However, when completed, I cannot locate any of the transfered material on the Mac! Any suggestions?
You have posted to the older PPC iMac forum. You need to poster to a newer iMac forum.
I suggest posting here:
https://discussions.apple.com/community/mac_os/mac_os_x_v10.7_lion?tagSet=1382
Complete list:
https://discussions.apple.com/docs/DOC-2463
Try double clicking on the harddrive icon on your desktop
You should get something like this.
On the left pane is a list of common places.
All the user data is in the /Users folder.
See the magnifying glass on the upper left of the screen. This is spotlight. Type in a file name.
Robert -
I am able to share the Library from the Mac laptop but not the Imac. Any suggestions?
You can share multiple libraries with the Apple TV, they don't even need to use the same iTunes account. Just make sure that you use the same ID for homesharing on all devices.
-
My laptop was stolen and I need to be able to connect my iPhone4 to the new laptop and transfer content (photos, mp3's, apps etc.) to the new laptop. I'm afraid to try a sync in case it deletes all the content off the iPhone. Any suggestions?
You should be importing all pics taken with the iphone to your computer regularly as you would with any digital camera.
iOS: Importing personal photos and videos from iOS devices to your computer -
System preferences is asking me to put in my apple id password for my email acct. I forgot the password so I hit forgot password and it won't take me to another screen to reset the password. Any suggestions?
You can reset your password of the apple ID via this site:
https://iforgot.apple.com/cgi-bin/WebObjects/DSiForgot.woa/wa/iforgot -
Since installing Mavericks, my screen periodically becomes pixelated, forcing me to reboot to resolve the problem. I've tried reinstalling Mavericks which failed to resolve the problem. Any suggestions?
You may have the mid-2010 problem. There's an issue with the graphics module on that machine. There was a program in place to replace the motherboard within 3 years of purchase, but you're probably outside of that. Some folks have supposedly gotten theirs changed outside of that period, so you can try.
http://support.apple.com/kb/TS4088?viewlocale=en_US&locale=en_US
What you can do to use it is download gfxstatus from http:gfx.io and force the graphics to Intel. -
Where can I download iBooks for Mac? I did not find it in APP store. Thanks
Where can I download iBooks for Mac？ I did not find it in APP store. Thanks
Do you have a backup. If so you should be able to restore it from that. Otherwise you can reinstall OS X. See Carolyn's post in I accidentally deleted iBooks on my Macbook Pro (late 2011) running on OS X 10.10.1 Yosemite. Will iBooks be reinstalled if I install the next OS X major update once it is out?
-
I have a lot of HD video on my hard drive that I eventually want to edit in iMovie, but just don't have the time now. It is clogging up the computer, though. How do I take the Hd clips off Mac for later editing?
See "Storage drive" here
Most commonly used backup methods
Th problem with HD video is it needs a fast external interface, so you should pick a external drive that uses the fastest interface your computer has to offer.
Performance rank fastest to slowest is
Thunderbolt, USB3, (newer Mac's)
Firewire 800, USB 2, Firewire 400, USB 1 (older Mac's)
Newer Windows PC's have USB3, older one's USB 2,1.
You need to format the drive if it comes FAT which a lot do, as FAT has a 4GB file size limit, so this won't work with large HD video files.
So if your going to use the drive only with a Mac, then head to Utlities > Disk Utility and format it Options: GUID Format: OS X Extended Journaled. (select the drive makers name and click Partition tab)
If your going to use the external drive with a PC, take it to the oldest PC you have and right click and format exFAT.
If you have a Windows XP machine and there is no exFAT, it can be downloaded for free from Microsoft.
Drives, partitions, formatting w/Mac's + PC's -
Comcast just replaced my cable modem/wireless router. All devices connect properly except my iPhone 4. It shows itself to be connected to the network, but it does not load any web page. Resetting the iPhone does not solve the problem. Any suggestions?
Thank you for your response.
I had rebooted the router (several times, actually), to no avail.
I do not know the answer to whether MAC filtering is enabled on the router. Have tried to find info about that, but unsuccessfully. Router is an Arris TG852G, supplied by Comcast. I would be surprised if MAC filtering were the issue, since in addition to the computer, we have successfully connected several other devices to the wifi, namely an iPad, a Android phone and a Kindle Fire - all able to access internet pages through the wifi, and all without a need to add the device to a MAC address whitelist. To add to the mystery, the Comcast tech was able to connect his iPhone 4 to my network and access web pages. He was unable to connect my iPhone, however, after trying for some time.
I seem to recall reading somewhere that an iPhone cannot connect to a wireless "n" router, only "b" or "g". The Arris router is described as a n/g/b compliant router, and as noted the Comcast tech was able to connect his iPhone, so don't know why that would be the issue here.
By the way, my iPhone does connect wirelessly to my network at home. This difficulty is at a second home.
Any other thoughts would be appreciated.
Maybe you are looking for
-
Applications Quit Unexpectedly
For some reason, When I try to open Toast Titanium I keep getting an error message that says the application has quit unexpectedly before it ever opens. I have used this program dozens of times in the past so I know it is ok. Any ideas? I have sent t
-
Freight Condition not getting copied from order to billing
Hi, Here at my clients place, i have created new condition type for freight(which will be calculated after excise duty and VAT).This conditon type should not increase the order value but increase tax amount in sales order item level. For this i have
-
My homes IPTV systems were just upgraded to a Microsoft Media Room system with Cisco set top boxes. My previous system also had Cisco set top boxes. The remotes (AT6400s) look the same for both systems except the old ones were a dark grey color and t
-
I've synced my phone with my facebook account so my friends will be included in my contacts. However, the profile pictures will not transfer. What am I doing wrong/
-
Hi All I am having a strange problem. The JSP file is taking to much of time to load and the IE doesnot responds properly even after the the page is loaded. I agree that the JSP has significant amount of Java code in it. What could be the problem?? T