I cannot connect to an existing network

I'd like to use AE to connect wirelessly to a USB printer. I've followed all of the instructions to set-up AE to the letter. I get a connection to the Airport Base Station. The light on the AE goes to solid green for about 4 seconds and then it starts to flash amber.
Suggestions?

Good morning James:
I've tried setting up with the printer connected and without and I still have the same problem.
Thanks

Similar Messages

I installed Mountain Lion on my iMac. Now I cannot access the Internet. All the other computers and tablets have no problem. I did PRAM and MC reset, modem reset, etc., all the usual ju-ju. I also cannot connect on my local network to any other computer.

I installed Mountain Lion on my iMac. Now I cannot access the Internet. All the other computers and tablets on the network have no problem. I did PRAM and MC reset, modem reset, etc., all the usual ju-ju. I also cannot connect on my local network to any other computer. Yet Network control panel says I am connect to the modem, and Network Diagnosis says I am connected to the Internet. It's like the blind man who has eyes that cannot see. BTW, I am not some newbee. I have been a Machead since the early nineties and set up a half dozen networks, including the one I am using at home to which the iMac mysteriously is there but not. This has me stumped! I am considering going back to 10.7!

Select  ▹ System Preferences ▹ Network ▹ Advanced ▹ TCP/IP. What values are shown for the following:
Configure IPv4
IPv4 Address
Subnet Mask
Router

TS3297 I keep getting the error 306 cannot connect to the iTunes Network when downloading songs on iTunes. I've tried all the troubleshooting steps from the forums and my technical issues are still unresolved. I have Windows 7. Please help!!

I keep getting the error 306 cannot connect to the iTunes Network when downloading songs on iTunes. I've tried all the troubleshooting steps from the forums and my technical issues are still unresolved. I have Windows 7. Please help!!

iTunes Store loads partially or returns "Error 306" or "Error 10054"
Proxies, parental control settings and software, security or filtering software, or a bad iTunes Store cache can cause this.
To address proxies, Remove Internet Options proxy settings ( http://support.apple.com/kb/TS1490 ) and connect to the Internet without a proxy.
To reset iTunes Store cache:
In iTunes, choose iTunes > Preferences (Mac) or Edit > Preferences (PC).
Click the Advanced tab.
Click the "Reset cache" button.
Click OK and see if the issue is resolved.
Adjust Parental Controls in iTunes:
Open iTunes.
Access iTunes preferences:
On a Mac: From the iTunes menu, choose Preferences.
On a Windows PC: From the Edit menu, choose Preferences.
Click the Parental Controls tab.
Remove restrictions on Parental Controls.
For more information on parental controls or content filtering software, see iTunes 10.5 for Windows: May see performance issues and blank iTunes Store.
http://support.apple.com/kb/TS4123?viewlocale=en_US

Airport express connected to my existing network - Can I connect a device to the network through it's ethernet port?

Is it possible when my airport express is wirelessly connected to my existing network - to connect a device to the network through it's ethernet port or is it wireless only at that point?
I'm trying to connect my A/V Receiver in another room to my network without having to run a CAT5 cable all the way to the router. I'd rather be able to connect it to my airport express if it will work that way.

Is it possible when my airport express is wirelessly connected to my existing network - to connect a device to the network through it's ethernet port or is it wireless only at that point?
Yes.....IF
You have an AirPort Express 802.11"n" version configured to "join a wireless network" and you have enabled the option to "Enable Ethernet Clients"
Or
You have an AirPort Express 802.11"n" configured to "extend a wireless network" from another Apple "n" router, in which case the Ethernet port is enabled by default

HT4262 I have two networks one each in two cities. Both are named the same but require different passwords. I am at my second location but cannot connect to his wifi network. How do I delet one network so I can connect to my second network?

I have two networks one each in two cities. Both are named the same but require different passwords. I am at my second location and cannot connect to this wifi network. How do I delet one network so I can connect to my second network?

Just go to the wireless network preferences and empty out all the stored wireless networks.. then scan and connect to the local wireless.
Select them and tap the - button below it.
Once they are emptied out.. it might be good to reboot the computer with the remember networks unchecked.
Start with a clean slate.

Cannot connect to the wireless networking

My Toshiba Laptop was preinstalled with Windows 7 Home premium 64-bit OS, and it had been working quite well with the wireless BB. However, the wireless internet connection was on and off within recent weeks, while the other mobile devices, such as iphone, ipad, or laptop, in my household had no such problem. The wireless signal was so strong, but the error message always said 'Windows cannot connect to the wireless networking'. It seemed there was something wrong with the wireless adapter.
I got a new TP-Link wireless adapter properly installed. Luckily, this worked; but unluckily, this worked for less than 24 hours. It was really frustrating that I, as a full-time student, depended so much on wireless networking.
Please help!!! Harry

Hi there
You may want to enlighten us with:
- What model are You using (f.ex. L300-123)
- What BIOS version is installed?
- What WLAN driver are You using?
All these questions are answered in PC Diagnostics found under Toshiba app folder in the start menu.
BR
Tom

Connect TimeCapsule to existing network

My parents have an old G5 iMac with no airport built in.
They do have a Time Capsule (connected with ethernet to their computer) with which they like to connect to an existing wireless network (different modem/router).
The iMac and modem cannot be connected via ethernet; they are too far apart. I tried to let TC 'connect to existing network' but that was not an option.
I only saw:
- create new network
- expand existing network.
If I choose the expand option, it finds several networks from the neighboarhood, but not their own. (The network does works wirelessly - I have no troubel connecting to it via my iPhone, anywhere in the house). Apparently the current network does not allow expanding.
Is there anything I can do just to let the TC join the existing network? And if so, will it still work well with Time Machine?
Thank you very much!

There is an issue with the MAC address of clients being hidden.. Apple was technically correct to leave it off.. but for home usage.. which after all, these devices are for.. they are not business products.. then I don't really care if the MAC addresses of the clients are hidden behind the repeater or not. The Express with one port effectively could still have the issue.. if you plugged a switch into it.. but Apple let it pass.
In the end it is as much about business as about technically correct method of operation.. after all.. if they can get you to buy yet another product who is winning??

Trouble with Time Capsule & Mountain Lion - unexpected error occurr when setting up connection to an existing network

Hi,
My TC was working perfectly fine until 2 weeks ago...
I have 2 MacBook Pro 2009 & 2012, I used the TC has wireles external hard disk for Time Machine.
I installed Mountain Lion on my oldest MacBook Pro (the newest has already Mountain Lion installed) 2 weeks ago. The installation was not straight forward... I tried to perform a clean installation, but I had difficulties with some applications.. anyway after a few days, everything went fine and smooth, I had to reconnect my TC with but it works fine, I could perform a few back-up with Time Machine.
But ... since 5 days ago, my TC is not find any more when I enter Time Machine... I went to Utility Airport and the TC was not connected, just circeld with dashed line and I cannot enter the set up mode.. I tried several things that did not worked and finally performed a reinitialisation of my TC with restauration of factory setting. This helped a bit because I could finally see my TC in utility arport in the wifi connected devices. I tried to et up my TC and connect it to an existing network. It went fine when specifying on whch network I want to connect, chossing a name for the TC and its password.
But then... I got an error message: An unexpected error has occured. Retry. I never get the window asking for the password for the network.
I retried but, It did not help, now the airport is no more visible in the wifi connected devices in airport utility...
Any thoughts, ideas?
Thanks,
Yvan

If you have a clean install of Mountain Lion it will remove the 5.6 utility.. but this is still better for setups than the new one. .. certainly for Gen4 TC or earlier.
The setup of the TC manually from v5 utility.
Make sure you use all short names.. for the TC itself and for wireless.. I recommend different name for 5ghz as well.
Use WPA2 Personal security and fix wireless channels.. check 11, 6, 1 in that order.
For 5ghz try around 40 and around 150.. doesn't matter which one.
Use ethernet if wireless fails..
You will hate me but older Mac with ML upgrade that went badly.. sorry get some help to clean install. the wireless in the Mac itself is then the issue.

Time Capsule cannot add to an existing network

Hi
How fustrating...my Time Capsule was working completely until it stopped backing up for no known reason. I have tried to reset the Time Capsule and add to an existing network but an unexpected error keeps occuring. I also tried a hard reset but this does not even work as my previous settings are still shown when it I plug it in again.
I have a wireless network setup from my Internet provider modem and I would like to use my time capsule as a backup only where I can place it into a seperate room to provide me with reassurance if something were to happen.
I have also connected Ethernet cable from TC LAN to iMac...again not even sure if my connections are correct.
Can something suggest something I should be doing...the TC setup guide is not very helpful.

You can install 5.6 utility on any OS up to Mavericks no problems.. you have to do it manually.
How to load 5.6 into later Lion & ML
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
Leave the package open on the desktop so you can see the file. AirportUtility56.pkg
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. If your Mac refuses to run the software, because it wasn’t downloaded from the Apple store, go to security in preferences and allow other software to work.. this is limitation of trade methinks. You can set back later if you like.
Now drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. in finder, open the new directory, drill down.. applications, utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall version 6 (now 6.3 if you updated) so don't try.. and you cannot or should not run them both at the same time.. although I have had no problems when doing so.

Cannot connect to printer over network from Linux

When I run hp-setup, I can get the printer listed but it appears to refuse to communicate with the device. Same problem for wired ethernet as well as wireless.
Please help, I think I have tried everything by now...
Firewall disabled on the workstation does not help. Talking to the printers web interface (:8080) works perfectly. The printer works perfectly via USB. Also works fine from another windows PC (networked)
System:
Linux Mint 17 - X86_64 (up to date)
uninstalled the mint hplip package and installed the latest from HP manually....
hp-setup
HP Linux Imaging and Printing System (ver. 3.14.10)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-13 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Searching... (bus=usb, search=(None), desc=0)
error: No devices found on bus: usb
Searching... (bus=net, timeout=5, ttl=4, search=(None) desc=0, method=slp)
error: Unable to communicate with device (code=12): hpfax:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
error: Unable to communicate with the device. Please check the device and try again.
Done.
hp-doctor output:
> hp-doctor
HP Linux Imaging and Printing System (ver. 3.14.10)
Self Diagnse Utility and Healing Utility ver. 1.0
Copyright (c) 2001-13 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Checking for Deprecated items....
No Deprecated items are found
Checking for HPLIP updates....
Latest version of HPLIP is already installed.
Checking for Dependencies....
| SYSTEM INFO |
Kernel: 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 GNU/Linux
Host: stargate
Proc: 3.13.0-24-generic #47-Ubuntu SMP Fri May 2 23:30:00 UTC 2014 GNU/Linux
Distribution: linuxmint 17
Bitness: 64 bit
| HPLIP CONFIGURATION |
HPLIP-Version: HPLIP 3.14.10
HPLIP-Home: /usr/share/hplip
HPLIP-Installation: Auto installation is supported for linuxmint distro 17 version
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.14.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.14.10
html=/usr/share/doc/hplip-3.14.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
bin=/usr/bin
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
libusb01-build=no
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.14.10
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
lite-build=no
udev_sysfs_rules=no
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
Plugins are not installed. Could not access file: No such file or directory
Current contents of '~/.hplip/hplip.conf' file:
[installation]
date_time = 12/29/2014 22:32:01
version = 3.14.10
[upgrade]
notify_upgrade = true
last_upgraded_time = 1419919247
pending_upgrade_time = 0
latest_available_version = 3.14.10
[settings]
systray_visible = 0
systray_messages = 0
[last_used]
device_uri = "hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32"
printer_name =
working_dir = .
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
interval = 5
device_list =
[fax]
voice_phone =
email_address =
<Package-name>        <Package-Desc>      <Required/Optional> <Min-Version> <Installed-Version> <Status>   <Comment>
| External Dependencies |
policykit            Admin-Policy-framework    OPTIONAL        -               0.105           OK         -
gs                   Ghostscript               REQUIRED        7.05            9.10            OK         -
network              Network-wget              OPTIONAL        -               1.15            OK         -
scanimage            Shell-Scanning            OPTIONAL        1.0             1.0.23          OK         -
avahi-utils          avahi-utils               OPTIONAL        -               0.6.31          OK         -
dbus                 DBus                      REQUIRED        -               1.6.18          OK         -
cups                 CUPS                      REQUIRED        1.1             1.7.2           OK         'CUPS Scheduler is running'
xsane                SANE-GUI                  OPTIONAL        0.9             0.998           OK         -
| General Dependencies |
reportlab            Python-PDF-Lib            OPTIONAL        2.0             3.0             OK         -
libcrypto            OpenSSL-Crypto-Lib        REQUIRED        -               1.0.1           OK         -
pil                  Python-Image-Lib          OPTIONAL        -               1.1.7           OK         -
pyqt4-dbus           PyQt4-DBUS                REQUIRED        4.0             4.10.4          OK         -
libjpeg              JPEG-Lib                  REQUIRED        -               -               OK         -
libpthread           POSIX-Threads-Lib         REQUIRED        -               2.19            OK         -
python-dbus          Python-DBUS               REQUIRED        0.80.0          1.2.0           OK         -
python-devel         Python-SDK                REQUIRED        2.2             2.7.6           OK         -
pyqt4                Python-Qt4                REQUIRED        4.0             4.10.4          OK         -
cups-devel           CUPS-SDK                  REQUIRED        -               1.7.2           OK         -
sane-devel           SANE-SDK                  REQUIRED        -               1.0.23          OK         -
libusb               USB-Lib                   REQUIRED        -               1.0             OK         -
sane                 Scan-Lib                  REQUIRED        -               1.0.23          OK         -
cups-image           CUPS-Image-Lib            REQUIRED        -               1.7.2           OK         -
libnetsnmp-devel     SNMP-Networking-SDK       REQUIRED        5.0.9           5.7.2           OK         -
python-xml           Python-XML-Lib            REQUIRED        -               2.1.0           OK         -
python-notify        Desktop-notifications     OPTIONAL        -               -               OK         -
| Compile Time Dependencies |
gcc                  gcc-Compiler              REQUIRED        -               4.8.2           OK         -
libtool              Build-tools               REQUIRED        -               2.4.2           OK         -
make                 GNU-Build-tools           REQUIRED        3.0             3.81            OK         -
| Python Extentions |
cupsext              CUPS-Extension            REQUIRED        -               3.14.10         OK         -
pcardext             PhotoCard-Extension       REQUIRED        -               3.14.10         OK         -
hpmudext             IO-Extension              REQUIRED        -               3.14.10         OK         -
| Scan Configuration |
hpaio                HPLIP-SANE-Backend        REQUIRED        -               3.14.10         OK         'hpaio found in /etc/sane.d/dll.conf'
scanext              Scan-SANE-Extension       REQUIRED        -               3.14.10         OK         -
| DISCOVERED SCANNER DEVICES |
device `hpaio:/net/HP_Officejet_Pro_8620?ip=192.168.1.32' is a Hewlett-Packard HP_Officejet_Pro_8620 all-in-one
device `hpaio:/net/Officejet_Pro_L7600?ip=192.168.1.31' is a Hewlett-Packard Officejet_Pro_L7600 all-in-one
| DISCOVERED USB DEVICES |
No devices found.
| INSTALLED CUPS PRINTER QUEUES |
HP_Officejet_Pro_8620
Type: Printer
Device URI: hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
PPD: /etc/cups/ppd/HP_Officejet_Pro_8620.ppd
PPD Description: HP Officejet Pro 8620, hpcups 3.14.10
Printer status: printer HP_Officejet_Pro_8620 is idle. enabled since Mon 29 Dec 2014 10:06:03 PM PST
error: Unable to communicate with device (code=12): hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
error: unable to open channel
error: Communication status: Failed
HP_Officejet_Pro_8620_fax
Type: Fax
Device URI: hpfax:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
PPD: /etc/cups/ppd/HP_Officejet_Pro_8620_fax.ppd
PPD Description: HP Fax4 hpcups
Printer Backend /usr/lib/cups/backend/hpfax does not exist! enabled since Mon 29 Dec 2014 10:06:03 PM PST
error: Unable to communicate with device (code=12): hpfax:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
error: unable to open channel
error: Communication status: Failed
Officejet_Pro_L7600_2
Type: Printer
Device URI: hp:/net/Officejet_Pro_L7600?ip=192.168.1.31
PPD: /etc/cups/ppd/Officejet_Pro_L7600_2.ppd
PPD Description: HP Officejet Pro l7600, hpcups 3.14.3
Printer Backend /usr/lib/cups/backend/hp does not exist!ince Sun 28 Dec 2014 10:55:35 AM PST -
Communication status: Good
Officejet_Pro_L7600_fax_2
Type: Fax
Device URI: hpfax:/net/Officejet_Pro_L7600?ip=192.168.1.31
PPD: /etc/cups/ppd/Officejet_Pro_L7600_fax_2.ppd
PPD Description: HP Fax hpcups
Printer Backend /usr/lib/cups/backend/hpfax does not exist!since Mon 10 Nov 2014 10:22:10 AM PST -
Communication status: Good
| PERMISSION |
Checking Permissions....
Permissions are correct.
Checking for Configured Queues....
Queue(s) configured correctly using HPLIP.
Checking for HP Properitery Plugin's....
No plug-in printers are configured.
Checking for Printer Status....
error: 'HP_Officejet_Pro_8620_fax' Printer is either Powered-OFF or Failed to communicate.
Turn On Printer and re-run hp-doctor
error: 'HP_Officejet_Pro_8620' Printer is either Powered-OFF or Failed to communicate.
Turn On Printer and re-run hp-doctor
Diagnose completed...

Syslog......
Dec 30 11:02:20 stargate hp-systray: io/hpmud/jd.c 93: unable to read device-id
Dec 30 11:02:20 stargate hp-systray: [29791]: error: Unable to communicate with device (code=12): hpfax:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
Dec 30 11:02:20 stargate hp-systray: hp-systray(hpdio)[29793]: error: Device not found
Dec 30 11:02:24 stargate hp-systray: io/hpmud/jd.c 93: unable to read device-id
Dec 30 11:02:24 stargate hp-systray: [29791]: error: Unable to communicate with device (code=12): hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
Dec 30 11:02:24 stargate hp-systray: hp-systray(hpdio)[29793]: error: Device not found
Dec 30 11:02:29 stargate python: io/hpmud/jd.c 93: unable to read device-id
Dec 30 11:02:29 stargate hp-toolbox: [30057]: error: Unable to communicate with device (code=12): hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32
Dec 30 11:02:29 stargate hp-toolbox: hp-toolbox(UI)[30057]: error: Unable to open device hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32.
Dec 30 11:03:03 stargate python: io/hpmud/jd.c 93: unable to read device-id
Dec 30 11:03:03 stargate hp-check: [30059]: error: Unable to communicate with device (code=12): hp:/net/HP_Officejet_Pro_8620?ip=192.168.1.32

HT5569 cannot connect to wi-fi network with my 2nd gen itouch even after following most troubleshooting solutions; have 3 other devices that connect with no problem (using wndr3700v3 dual router)

cannot connect to home wi-fi connection with my 2nd gen itouch even after following most troubleshooting solutions. i have 2 5-gen itouch ipods and a kindle fire hd 8.9 that can connecto to my wi-fi network and even download from my e-mail accounts with no problem. it had no problem connecting with my old a/b/g netgear router nor the first time i installed my new netgear wndr3700v3 router. since then, no connection. don't know what happened.
help

Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar
Could it be this:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
One user reported that placing the iPod in the freezer fixed the problem. A trick that works frequently with iPhones:
Settings > AirPlane Mode ON, Do Not Disturb ON
Power down and wait 5-10 minutes
Power up
Settings > AirPlane Mode OFF, Do Not Disturb OFF
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar

(iMac 5,1) 10.6.8 I cannot connect to Wi-Fi Networks. The Wi-fi preference isn't there what should I do

For some reason the wifi prefrence that is usually in the tool bar is not there. so therefore i cannot connect to any wifi connections

System Preferences, Network, then Turn it on:

My iPhone 4s cannot connect to my home network, can't figure out why...

My phone recognizes my home network but cannot join it. I have tried the option to forget the network and then gone back in and retyped in the password, but it just keeps spinning in a circle trying to connect to my home network, but never connects?
Both my iMac and Macbook have no problems being connected to the same network.
Any thought on what the problem could be?
Thanks

Have you tried to reset all network parameters? It may help.
Preferences > General > Reset > Reset Network Settings
Careful, DO NOT PRESS the other ones by mistake.

Cannot connect 8500a to wireless network

i input the mac address during wireless network install but cannot connect printer to network

Do you have MAC filtering enabled? The printer will not like it plus it is not in the least a security measure. I recommend disabling MAC filtering and just set the encryption to WPA2 with a strong, 13+ character, passphrase.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Cannot connect to printer on network

I recently moved house and want to recconect my wireless printer (Epson WorkForce 845) to my new network. My iad and iphone see the printer on the new network and print fine, so i know it is not a printer issue. Howeve my imac cannot connect to the printer. In Printers & Scanners, I have tried removing and ading back the printer. The problem is that the default printer only offers ""last Priner used or "Epson WorkForce 845". Selecting either fails to print and gives a "Stopped - 'Filter' failed" message.

I am having the same problem on our home network. Have enabled printer sharing on the mac and the PC but the mac does not "see" the printer hooked up to the pc.

I cannot connect to an existing network

Similar Messages

Maybe you are looking for