I cannot find "scan for instrument" at MAX

Hi~
I connected GPIB-USB-HS cable between the laptop and Keithley 2602 device.
In MAX, I could find GPIB-USB-HS "USB0::0x3923::0x709B::016F05B4::RAW" under "device&interface"
However, I cannot find "scan for instrument" anywhere!
So, I coudn't connect equipment with laptop......
What is the problem??
(I use Window 7, and I installed NI driver.)

duplicate post

Similar Messages

How can I get MAX to scan for instruments on bootup?

I would like to setup MAX (or whatever SW component) to scan for GPIB instruments each time the computer is booted up. I've had one strange case where MAX somehow "lost" it's GPIB instrument configuration and the only way to recover was to manually start MAX and do a scan for instruments. I already do this for the VXI resource manager.
PS - I see the VISA configuration file, visaconfig.ini, has an "AlwaysRefresh" option line. Is there anyway to set this short of a direct edit?
Thanks,
Ed Perkins

Scott - If I understand you correctly I should be able to do the following:
1. Disconnect the IEEE-488 cable from my computer.
2. Manually start MAX and tell it to scan instruments (which it will find none).
3. Plug the IEEE cable back in and re-run my application (it uses VISA to control both IEEE-488 and VXI instruments) successfully.
Correct?
What prompted this thread was one strange event. After successfully running our app the previous night (and leaving everything powered up) the app failed all IEEE calls the next morning. When we went into MAX it mysteriously showed no IEEE instruments. Nothing solved the problem (computer reboots, etc.) until we forced MAX to do an instrument refresh. Perhaps something else did go on, but I thought
running MAX and forcing an instrument refresh on each boot-up (much like running the VXI Resource Manager) would be a prudent prevention approach, especially since the station operators don't even know about MAX.
Thanks,
Ed Perkins

Scan for instruments MAX, GPIB

Hi!
I've got one problem. I made a program in Labview with two devices directed by GPIB. Now one of them don't work correctly. I did "scan for instruments" inside of MAX and now it only "see" one of them. I checked the connections and they're ok. I don't know what more try, because I change nothing and before it worked.
What can I do in order to this instrument appears again?
Thanks!
Solved!
Go to Solution.

First I would double check the GPIB addresses. Secondly, make sure both devices are in a normal state. I recently had a power supply go into an error mode and then refuse to talk over GPIB until I turned it off and then back on.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Concurrent Manager cannot find information for your conc req in FND_USER

Dear All,
Our customer is facing this issue while submitting conc requests. The requests end up in a Error with the following message in the Diagnostics.
Concurrent Manager cannot find information for your concurrent request from FND_USER
Cause: Concurrent Manager found no rows while selecting information for your concurrent request from FND_USER .
Sometimes it does not happen. It happens only for HRMS users. We are not sure what is causing this issue.
Anyone has faced this already? Highly appreciate your suggestions / pointers towards solving this issue.
Thanks in advance!
Hem

Hem,
Not sure if this is relevant here, but you may try to submit the following concurrent programs and see if it helps.
- "Sync responsibility role data into the WF table."
- "Synchronize WF LOCAL tables"
- "Workflow Directory Services User/Role Validation"
If the above does not help, enable trace/debug on any of those concurrent programs, and submit it again, check the concurrent request log file contents then (you do not have to generate TKPROF file, so skip this step).
Note: 453527.1 - How To Trace a Concurrent Request And Generate TKPROF File
https://metalink2.oracle.com/metalink/plsql/ml2_documents.showDocument?p_database_id=NOT&p_id=453527.1
Regards,
Hussein

I want to re-install Premiere Elelments 8, but cannot find downloads for version 8. Where can I download the files for version 8?

I want to re-install Premiere Elelments 8, but cannot find downloads for version 8. I have the serial no. Where can I download the files for version 8?

Hi Jeff. I did purchase Premiere Elements 8 from Adobe (download version), but couldn't find the files to download again on the adobe.com website. I did, however carry out another search of files from my old PC and eventually found the files to reinstall on my new PC, using my registered product serial no. Installation has worked. It seems that Adobe has stopped supporting version 8 as I could only find version 9 and later for download from the adobe.com website.
Thanks for your prompt reply

IDM with SQL server Error: Cannot find columns for the table...

Hi all,
I am Configuring IDM with SQL Server repository and ran into this error.
'Cannot find columns for the table 'object'
.....jdbc...[SQL Server]Invalid object name 'object'
Can anybody please help me!!
G

Yes, permissions are very important. I ran into a similar problem because I didn't have the correct permissions. Make sure the user has the following permissions:
CREATE ANY TABLE
ALTER ANY TABLE
DROP ANY TABLE
CREATE ANY PROCEDURE
EXECUTE ANY PROCEDURE
DROP ANY PROCEDURE
Also, make sure there is enough space in the default tablespace of that user.
HTH
~Suvesh

Cannot find InfoProvider for selection specified

Hi All,
When executed RSPLAN in BI System , it took us to EP screen , in that
InfoProvider , Aggregation Levels , Filter....etc tabs are there.
When selected InfoProvider , Z* or * or empty and when clicked on start button..
The following message is displayed :
Cannot find InfoProvider for selection specified "with green exclamatory symbol"
Even it is not giving JCo type of error message ,
Real time infocubes are created and activated .
The two above things have been checked properly .
Thanks,
Srini

Dear Srinivasa,
Check this link..
Cannot find aggregation levels for selection specified
not able to see infoprovider in the planning modeler
Hope this helps u..
Best Regards,
VVenkat...

Com.waveset.util.ConfigurationError: Cannot find columns for table 'object'

I am trying to install IDM on my own laptop and use MS SQL Server 2000 as the repository. I run the create table scripts, copy all the jar files to C:\Program Files\Apache Software Foundation\Tomcat 6.0\webapps\Idm\WEB-INF\lib. But I still got the following error message:
com.waveset.util.ConfigurationError: Cannot find columns for table 'object' ==>com.microsoft.sqlserver.jdbc.SQLServerException: Invalid object name 'object'
Does anyone have any idea of what may cause this problem?
THANKS!

I found the solution to this issue.. is that the Database user ID must be set to the schema .. this is the statment that probably did not work:
CREATE USER <username> FOR LOGIN <login name> with DEFAULT_SCHEMA = <database name>
In sql 2005 expand the database... open security .. find the user.. right click and select properties.. in the default schema box.. select the SunSync database .. in the schemas owned by this user select the sunsync schema database..
good luck

What does it mean if the system "cannot find driver for console framebuffer"?

I've just installed Solaris 7 on a SparcStation 20 with 256 MB RAM, 1 + 2 GB hard drives, 1xSuperSparcII. When I boot up it says "NOTICE:Cannot find driver for console framebuffer". I can't run the CDE, and I assume this is because there is no graphics driver. The graphics card (it's an add-on but by Sun) presumably needs a driver and I would have thought that this would have been included with the Solaris 7 CD. The whole thing worked fine when it was running Solaris 2.5.1 and now I've installed a new OS (initial as opposed to upgrade) it just don't work. Any ideas?

The "output-device" parameter may not be set properly in Open Boot Prom(OBP) and hence during installation, the driver may not be installed. To fix this, try the following steps.
1. Note down the current value for output-device. This value is to be restored later.
printenv output-device
2. Set the "output-device" parameter to "screen" in OBP
setenv output-device screen
3. Perform a reconfiguration boot using the command "boot -r"
4. The error will not appear. Verify that /dev/fb refers to a device link.
5. Go to ok prompt again and restore the output-device to its original value (as noted in step 1). The reason for doing this is that some resolution parameters would have been set earlier for your output-device.
6. Reboot the system again. The error may appear again but since the device link is already created, the CDE will work.
Please contact us if there are any issues.
Thanks
Srinivasan

Cannot find JDI for EP7.0 !

Hello experts,
I am supposed to install JDI on our environment (EP7.0 SP11) but I cannot find the particular Support Packages nor I can find installation documentation. I was not a problem for ver.6.40 but this NetWeaver 2004s version is a different story.
Please help to desperate rookie, points are guaranted!
Regards,
Frank

Hi,
You've 3 options as I know.
Option1:
Refer to page 98 on SAP Netweaver 7.0 Installation Guide for Java.
From NW7.0 these are called Usage Types. (Usage type for DI - Development Infrastructure)
The following is an excerpt.
After SAPinst has finished, you need to run the configuration task for usage typeDI using the
Configuration Wizard.
1. Under Scenario choose DI.
2. Decide whether you want to install and run the entire NWDI on this system or configure the
services individually:
Recommendation
We recommend that use the first option shown below, to install and run the entire NWDI on
this system.
n To install and run the entire NWDI on this system, perform the following steps:
a) Choose the Scenario DI
b) Choose All-in-one Complete Configuration of DTR, CBS, and CMS
c) Fill the open fields in the section Data Entry according to their label.
d) To run the configuration task, choose Execute Template.
n To configure the services individually (DTR, CBS, CMS) ‒ for example, because you have
distributed the usage type DI to different servers ‒ perform the following steps:
a) Choose the Scenario DI
b) Choose the service you want to configure, Design Time Repository, Component Build Service, or
Change Management Service.
c) Fill the open fields in the section Data Entry according to their label.
d) To run the configuration task, choose Execute Task.
e) Choose the items that you need from Design Time Repository Configuration, Component Build Service,
and Change Management Service.
92/168 PUBLIC 08/31/2007
5 Post-Installation
5.16 Checking the SAP Java Documentation
Note
Before performing any database settings make sure that you have read SAP Note 889038.
3. If you are using a new Oracle database installation, perform the step Set Oracle Parameters for DI.
Caution
Do not use this for an already configured database because it overwrites previous settings.
4. After the Configuration Wizard has finished, you have to restart the engine as described in SAP
Note 919942.
Option2: (you need to have service marketplace id)
Alternatively, you can download the necessary SCA files and deploy them on the Server by SDM and follow post configuration steps.
https://websmp105.sap-ag.de/swdc
Download -> Support Packages -> Entry by Application Group
Support Packages and Patches -> SAP NetWeaver -> SAP NETWEAVER -> SAP NETWEAVER 7.0 (2004S) -> Entry by Component -> Development Infrastructure
You'll need
DI CHANGE MGMT. SERVER 7.00
DI COMPONENT BUILD SERVER 7.00
DI DESIGN TIME REPOSITORY 7.00
Setting up NWDI:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/e0f341af-e86e-2910-3e8a-d9e3c227d938
Option3:
Use Solution Manager (i've no idea)
Hope that helps.
Regards,
Rajit
Message was edited by:
Rajit Srinivas

Cannot find symbol for some jms methods

Hi, I'm new to JMS and am having trouble compiling the HelloWorld example. I am able to create a connection but for some reason I cannot create a session from the same connection. I am however able to call some of the other methods such as getClientID, start, and close. Below is a copy of what i have compiled so far (which is basically a copy of the example code), the error message I get, and what I have CLASSPATH set to. If my CLASSPATH is not set correctly, I would assume none of the code would compile which is very confusing. Any help is appreciated, thanks!
//Step 1:
//Import the JMS API classes.
import javax.jms.ConnectionFactory;
import javax.jms.Connection;
import javax.jms.Session;
import javax.jms.MessageProducer;
import javax.jms.MessageConsumer;
import javax.jms.Queue;
import javax.jms.Session;
import javax.jms.Message;
import javax.jms.TextMessage;
import javax.jms.*;
//Import the classes to use JNDI.
import javax.naming.*;
import java.util.*;
public class HelloWorldMessage
public static void main(String[] args){
     System.out.println("Hello World!");
     try{
Queue myQueue;
     // Instantiate a Oracle GlassFish(tm) Server Message Queue ConnectionFactory administered object
     com.sun.messaging.ConnectionFactory myConnFactory = new com.sun.messaging.ConnectionFactory();
     // Create a connection to the Oracle GlassFish(tm) Server Message Queue Message Service.
     Connection myConn = myConnFactory.createConnection();
     myConn.getClientID();
     // Create a session within the connection.
     Session mySess = myConn.createSession(false, Session.AUTO_ACKNOWLEDGE);
     myQueue = new com.sun.messaging.Queue("world");
     myConn.close();
     catch(Exception jmse){
     System.out.println("Exception occurred : " + jmse.toString());
jmse.printStackTrace();
# javac HelloWorldMessage.java
HelloWorldMessage.java:39: cannot find symbol
symbol : method createSession(boolean,int)
location: interface javax.jms.Connection
     Session mySess = myConn.createSession(false, Session.AUTO_ACKNOWLEDGE);
     ^
1 error
# echo $CLASSPATH
.:/usr/java/default/j2sdkee1.3/lib/j2ee.jar:/usr/java/default/j2sdkee1.3/lib/:/root/MessageQueue/mq/lib/fscontext.jar:/usr/lib/jvm-exports/java-1.6.0-openjdk-1.6.0.0.x86_64/jndi.jar:/root/MessageQueue/mq/lib/jms.jar:/root/MessageQueue/mq/lib/imq.jar:/root/MessageQueue/mq/lib/jaxm-api.jar:/root/MessageQueue/mq/lib/imqxm.jar:/root/MessageQueue/mq/lib/imqservlet.jar
Edited by: 883631 on Sep 6, 2011 4:03 PM

You have an old j2ee.jar from 1.3 in your CLASSPATH.
Can you move jms.jar and imq.jar in front of that old j2ee.jar?
Thx/

Cannot Find Documentation for DAQmxSetTrigAttribute

Dear all,
The example program that comes with NIDAQmx (DigPulseTrain-Cont-PauseTrig) uses a function called DAQmxSetTrigAttribute but I cannot find any documentation on the use of this function or any of the others in the same block within the NIDAQmx.h header file:
The example program contains the following lines:
DAQmxErrChk (DAQmxSetTrigAttribute(*taskHandle,DAQmx_PauseTrig_Type,DAQmx_Val_DigLvl));
DAQmxErrChk (DAQmxSetTrigAttribute(*taskHandle,DAQmx_DigLvl_PauseTrig_Src,triggerSource));
DAQmxErrChk (DAQmxSetTrigAttribute (*taskHandle, DAQmx_DigLvl_PauseTrig_When,pauseWhen));
And the NIDAQmx.h header file contains these function definitions:
int32 DllExport __CFUNC_C DAQmxGetTrigAttribute (TaskHandle taskHandle, int32 attribute, void *value, ...);
int32 DllExport __CFUNC_C DAQmxSetTrigAttribute (TaskHandle taskHandle, int32 attribute, ...);
int32 DllExport __CFUNC DAQmxResetTrigAttribute (TaskHandle taskHandle, int32 attribute);
Does anybody know what the different parameters are and how to use these functions?
Regards
Martin Dale

The attribute ids that are valid for the DAQmxSetTriggAttribute() are in the NIDAQmx.h file can be found under the heading
"//********** Trigger Attributes **********"
These include attributes for start, reference, pause, and arm start triggers.
I hope this helps!
gus....

Cannot find Internet for RESTORE but can go to ITunes Library

I have the 40gig IPod attached and seen by ITunes. I am able to go to the ITunes store without a problem. But when I want to Restore or Check for Upgrade, message says it cannot find connection to the Internet. Yet I can get on the Internet with Windows Internet Explorer immediately.
I am running Windows XP. Any suggestion would be appreciated.

There could be a few issues here...
First: Is this a business computer? If so, you may want to check in with your IT department and have them up the security level of Itunes...
I'm guessing you may have updated itunes recently...
Secondly: If its a personal computer check your firewall... When you update itunes it is considered a new program by your firewall programs...(IE Mcafee/norton/windows firewall) What you will need to do is adjust your itunes security levels, allowing itunes to have full access to the internet.
Thirdly: If you arent the Administrator on this computer it may be a simple setting in your accessibility options.
If you have any more info i may be able to be of more service to ya.

Jardiff Failing Cannot find path for creation

I get the following error when I try to enable versioning:
2002-08-12 17:54:53 Generating JarDiff for spotlight.jar 1.4->1.5
2002-08-12 17:54:53 Failed to genereate jardiff
java.io.IOException: The system cannot find the path specified
     at java.io.WinNTFileSystem.createFileExclusively(Native Method)
     at java.io.File.checkAndCreate(File.java:1294)
     at java.io.File.createTempFile(File.java:1382)
     at java.io.File.createTempFile(File.java:1419)
     at com.sun.javaws.servlet.JarDiffHandler.generateJarDiff(JarDiffHandler.java:156)
Any ideas

What version of java are u running the servlet on ?

Outlook cannot find file for icloud

Updated to latest version of itunes and cannot access files for contacts and calendar on my Windows 8 machine. Iphone and Ipad are OK.

Updated to latest version of itunes and cannot access files for contacts and calendar on my Windows 8 machine. Iphone and Ipad are OK.

I cannot find "scan for instrument​" at MAX

Similar Messages

Maybe you are looking for

I cannot find "scan for instrument" at MAX