I cannot get out of a frozen state on my iPad. It is showing Itunes and usb connection images on screen

PLease help me get my IPAD out of this frozen state. It is showing the Itunes and USB connection image. It will do absolutely nothing! HELP!!!

Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.

Similar Messages

My ipad 2 just shows itunes and plug icon my computer wont take new version of itunes too old how do i get my ipad 2 working do not care about saving data just want to use this very expensive useless item!

My ipad 2 just shows itunes and plug icon my computer wont take new version of itunes too old how do i get my ipad 2 working do not care about saving data just want to use this very expensive useless item!

My iPad2 works great now after IOS 8.1 Update
I did my iPad2 update thru iTunes on my iMac and it was sucking the iMacs memory very low during the update. Safari froze before loading the first web page and I did a hard boot and went fishing as I saw where it was going to take a long time to recover. When I tried again it wasn't quite right and then did one more hard boot and then did a Reset by going to General-Reset-"Reset all Settings" and it works real well now without loosing any data and in-home wi-fi clocks at 17Mbps download. Probably like most of you I’m sticking with OSX 10.9.5 Mavericks as it gets the job done very nicely and don’t need all that extra fancy stuff that probably will slow things down.

Unit showing iTunes and USB cable only and iTouch is "frozen"

Here is how I cleared this up and got the unit working again after downloading and installing 2.2.1 and hosing up the unit. Some of these steps may not have been needed, but it worked for me!
Loaded iTunes to another pc (Windows XP). Opened iTunes and connected the unit via a usb and now iTunes did recognize my unit. My regular machine would not even do that! iTunes said a unit that was in "recovery mode" and you could not use it with iTunes until it was "reset". So I clicked on "reset" and got connected with the download on Apple and it started downloading the files necessary, it said. Found out later it was the 2.2.1 upgrade. Anyway after several hours the download finished. I then held down the "shift" key and clicked "restore" at the same time and a window opened and I had to search for the download which was in "document and settings, owner, application data, Apple Computer then iPod software update and there was the file. I opened that and it started working on the iTouch. After it completed, I moved the unit to my regular pc and it then recognized my unit and I hit restore again (I am a little hazy about this step because I got real excited when the unit was recognized, but if you get his far I think you can figure it out) and it set my unit back to it's old self. I then had to resync the music, applications etc.
So far everything is now working. If you have any questions, please yell. I have written this in a hurry and maybe some of it does not make sense.

I am not familiar with error 18. This article is my goto for all error codes
http://support.apple.com/kb/TS3694
When you see iTunes and the USB icon, you have to restore it. You may have to place it into recovery mode. Follow the instructions here if so.
http://support.apple.com/kb/HT1808

I brought up a larger screen by mistake (touched the wrong button) & now cannot get out of it. Can you help me to reduce the size of the picture on my screen as i cannot x out of it . thanks. don

how can I "x" out of what is on firefox. The picture fills the whole screen & I cannot find the "x" in the upper right hand corner.

You may be in Full Screen Mode. The F11 key toggles Full Screen Mode on or off.
*See --> http://kb.mozillazine.org/Netbooks#Full_screen
'''If this reply solves your problem, please click "Solved It" next to this reply when <u>signed-in</u> to the forum.'''

HT4623 on upgrading iPhone 4 to ios 6 using itunes it returned an unknown error then froze completely. It has the iTunes and USB connector on the screen. Reset is not working, I get the same frozen screen.

On upgrading iPhone 4 to ios 6 using iTunes, it returned an unknown error then froze completely with the iTunes icon and USB connector on the screen. Reset didn't work. iTunes doesn't recognize the devise anymore.

if your computer is not recognizing it, try using a different USB port or different usb cable. if that doesnt work you will need to uninstall and reinstall itunes.

Iphone screen has itunes and usb cable images frozen

I tried clearing my 3GS phone and now these two images are frozen on the screen. When connecting to iTunes it notes that it needs to be restored, but when I try it says it cannot be done.
Any idea if this device has already been erased or not?

Click 1013 on that page ---> iOS: Resolving update and restore alert messages

When I have documents open and I walk away for a few minutes, when I come back and try to resume working, my computer seems to freeze up and the little pinwheel starts spinning and I literally have to unplug my computer to get it out of this frozen state.

When I have documents open and I walk away for a few minutes, when I come back and resume working, my computer freezes up and the little pinwheel starts spinning. I literally have to unplug it to get out of this frozen state. This has been getting progressively worse over the past three months. I recently took it into the Genius Bar and they could not find anything wrong. They told me to add more memory, which I did. However, the problem persists. Do you know why my computer would freeze up after the screen has had no activity for just a few minutes? My screen saver is set for an hour so I know this is not the problem.

What kind of documents? Office? iWork? Text Edit? What version?
What settings do you have in regards to power saver and/or screen saver?
For these kinds of system glitches I always recommend installing and running Onyx 'Automation'. If that does not work you should reinstall the offending software, if possible.
Onyx - http://www.titanium.free.fr/download.php?sid=d1caebc01e3207556c6d75791305ccf2

I have a frozen email which i cannot get out of

ii have a frozen mail i am composing and i cannot get out of it and back to my inbox - help!

Try a reset. Hold the Sleep and Home button down for about 10 seconds until you see the Apple logo. Ignore the red slider.

TS4062 my phone has frozen on a screen to sync and I cannot get out

Help, cannot use my phone because it's frozen on a screen to sync and I cannot get out. Cannot even turn it off

it says "iCloud Backup - Backups happen when this iPhone is plugged in, locked and connected to Wi-Fi". Was trying to go into settings to turn back on wifi and it wouldn't let me get past this screen

HT4623 please help - installed IOS7 and now I am having problems playing Words Free on my Iphone. It gives me a pop up telling me to connect to ITunes but will not connect. Cannot get out and have to continually shut down my phone and start over.

please help - installed IOS7 and now I am having problems playing Words Free on my Iphone. It gives me a pop up telling me to connect to ITunes but will not connect. Cannot get out and have to continually shut down my phone and start over.

Hi, jeantwin.
Thank you for visiting Apple Support Communities.
The steps in the article below may help you resolve the issue with push notifications.
iPad and iPod touch: Unable to use YouTube or Push notifications
http://support.apple.com/kb/ts3305
If the issue persists, try signing out of your Apple ID and then sign back in.
iOS: Changing the signed-in iTunes Store Apple ID account
http://support.apple.com/kb/HT1311
Cheers,
Jason H.

Cisco ASA 5505 Cannot ping local traffic and local hosts cannot get out

I have, what I believe to be, a simple issue - I must be missing something.
Site to Site VPN with Cisco ASA's. VPN is up, and remote hosts can ping the inside int of ASA (10.51.253.209).
There is a PC (10.51.253.210) plugged into e0/1.
I know the PC is configured correctly with Windows firewall tuned off.
The PC cannot get to the ouside world, and the ASA cannot ping 10.51.253.210.
I have seen this before, and I deleted VLAN 1, recreated it, and I could ping the local host without issue.
Basically, the VPN is up and running but PC 10.51.253.210 cannot get out.
Any ideas? Sanitized Config is below. Thanks !
ASA Version 7.2(4)
hostname *****
domain-name *****
enable password N7FecZuSHJlVZC2P encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif Inside
security-level 100
ip address 10.51.253.209 255.255.255.248
interface Vlan2
nameif Outside
security-level 0
ip address ***** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
shutdown
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
shutdown
ftp mode passive
dns server-group DefaultDNS
domain-name *****
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list No_NAT extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.7.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.10.250
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.200
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.1.3.9
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.14
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.15
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 host 10.10.10.16
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.1.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 10.10.9.0 255.255.255.0
access-list Outside_VPN extended permit ip 10.51.253.208 255.255.255.248 ***** 255.255.255.240
pager lines 24
mtu Outside 1500
mtu Inside
icmp unreachable rate-limit 1 burst-size 1
icmp permit any Outside
no asdm history enable
arp timeout 14400
global (Outside) 1 interface
nat (Inside) 0 access-list No_NAT
route Outside 0.0.0.0 0.0.0.0 ***** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
aaa authentication enable console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set DPS_Set esp-3des esp-md5-hmac
crypto map DPS_Map 10 match address Outside_VPN
crypto map DPS_Map 10 set peer *****
crypto map DPS_Map 10 set transform-set *****
crypto map DPS_Map interface Outside
crypto isakmp enable Outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 28800
crypto isakmp policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 Outside
ssh timeout 60
console timeout 0
management-access Inside
username test password P4ttSyrm33SV8TYp encrypted
tunnel-group ***** type ipsec-l2l
tunnel-group ***** ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8d0adca63eab6c6c738cc4ab432f609d
: end
1500

Hi Martin,
Which way you are trying. Sending traffic via site to site is not working or traffic which you generate to outside world is not working?
But you say ASA connected interface to PC itself is not pinging that is strange. But try setting up the specific rules for the outgoing connection and check. Instead of not having any ACL.
If it is outside world the you may need to check on the NAT rules which is not correct.
If it is site to site then you may need to check few other things.
Please do rate for the helpful posts.
By
Karthik

HT1338 error in download, OS X 10.8.3 now checking for updates for 14 hours cannot get out of it!!!

Error with downloading upgrade OS X 10.8.3 now checking for updates for 14 hours cannot get out to start again!!!

Quit the App Store application, or force-quit if necessary.

Whenever I switch on my iPad Air , I am presented with a full screen of a blue sky, white clouds and stars, which I cannot get out of. How do I do so?

Whenever I switch on my iPad Air, I am presented with a full screen piture of a blue sky, stars and white clouds, which I cannot get out of. How do I do so, please?

Sorry, please ignore this question. I have just realised that the answer is the same as the one I recieved to a previous similar one.

Cannot get out of full-screen view of main window of Mail.

I went into full-screen with the main window of Mail, and now cannot get out of it, even when quitting and relaunching. Exiting full screen only shows separate window for the highlighted email. How can I reverse this?

Push your mouse cursor to the top until the menu drops down. At the far right corner is the leave full screen icon. Select it.

I hit the magnifier tool on my iPad and now it only shows a portion of the screen and I cannot get out of it. What do I do?

I hit the magnifier tool on my iPad and now it only shows a portion of the screen and I cannot get out of it. What do I do?

Which magnifier tool are you referring to? If you double-tap with 3 fingers it should disable zoom. Then you can go into Setttings>Accessibility>Zoom and turn it off.

I cannot get out of a frozen state on my iPad. It is showing Itunes and usb connection images on screen

Similar Messages

Maybe you are looking for