I cannot telnet into my WRT54GC linksys router

C:\>telnet 192.168.1.1 and a i get the following response Connecting to 192.168.1.1... Could not open connection to the host, on port 23: Connection failed. Someone to know how can I telnet my router?

I don't think the device has telnet access, try the web interface instead i.e. http://192.168.1.1

Similar Messages

Cannot Telnet into 1921 router

Please Help, I cannot telnet into my 1921 router and not sure how to fix this. See below.
line con 0
password 7 XXXXX
logging synchronous
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
password 7 XXXXXX
logging synchronous
login local
length 0
transport input none

Hello Brad,
Try entering
line vty 0 4
transport input telnet
Hope this helps,
if so, please rate.

Cannot telnet into router

What do I do when all of a sudden I can't telnet into my router through any interfaces?
I can ping the interfaces successfully, by IP and DNS name. Nothing has changed since the last successful login.
error msg:
Connecting To c3640...Could not open connection to the host, on port 23: Connect failed

The symptoms you describe sound like all the vty ports are in use. This may happen if you have configured the vty ports with no exec-timeout (or with exec-timeout 0 0 which is the same thing). If you can get to the console port the show user command (or the who command) should indicate which vty are in use - and I suspect that they all are.
If you can get to the console port and enable mode you could clear some of the sessions which would make telnet work again.
If you can not get to the console port you might wait and try later and see if it works after someone logs off. The other alternative is to reboot the router.
HTH
Rick

Cannot conect router WRT54gc linksys router using windows 7

when I connect router correctly via modem I get message not connected no matter what I do I am convinced I am doing nothing wrong having used linksys router a number of times before about 2 years ago using XP cannot someone help before I climb the wall to throw myself off please I am now connected to router now to get on internet to this site help please wanted

Let me know the name of the ISP- means it’s a cable connection or a DSL connection? Do you get the internet connection when you connect the modem directly to the computer? If yes, what IP address do you get on the computer? To check the IP address that you are getting from the Router...
You can check the IP address in the following manner:
# Click on Start -> All Programs -> Accessories -> Command Prompt.
# A black pop up box should come up, type: "ipconfig /all" …
There check the IP address and Default Gateway under LAN….

Cannot telnet into ACS 5.2

Cannot connect to ACS device using telnet IP: port 1812? Seems it is using this port config by default.
Is it because of the port it's trying to use? Is there a way of changing the port? If so, where does one do this in the ACS device?
I have two 4400 series WLC's one is on the same network segment as the ACS, I can authenticate through the ACS on this one. The other WLC at a different location, cannot authenticate through the ACS. But if can't telnet into it, it's probably not letting something through?
Any help would be greatly apprecieated!
Tandrist

Acs 5.1 supports ssh
Port 1812 is used for radius packets on the acs. Not telnet. Nor ssh.
Try a simple ping between tge wlc and the acs
Make sure the shared secret match between wlc and acs
Sent from Cisco Technical Support iPhone App

Cannot connect IBM Thinkpad to Linksys Router Wirelessly

I recently moved in with a friend, and my IBM Thinkpad T42, with Windows XP, cannot connect to her Linksys WRT120N router wirelessly. I am able to connect to the internet using an Ethernet cable, and I am able to connect to other public wireless networks.
I have been told by Cisco helpdesk people that it is because Windows XP does not support WPA2 security, and/or that because they don't know much about IBM computers, I should get rid of the third party internet connection software, IBM Access Connections, that came with my computer.
I have been having this problem for a week, and I did not even know I had IBM Access Connections until today, so I don't think that's the problem. Also, my friend has been using that application successfully on her computer, Thinkpad T61, Windows XP, to connect to this router, which she has been using for 2 years. So with two almost identical computers, does anybody know why my wireless connection isn't working?

Answer these questions, I may be able to give you the right solution to your issue:
1. Go to your Network Connections folder on your wired computer and check which one is connected:
a. Local Area Connection
b. Broadband Connection
c. 1394 Connection
2. What is the IP address of your computer?
3. Who is your internet service provider?
4. What is the error message when you connect the wireless computer to the network?

The host name cannot be resolve ? ( with linksys router )

Hi all, I have some problem with setting up a network. I tried to set my network according to http://wiki.archlinux.org/index.php/Configuring_network the network/internet is fine except the host name with "http://" cannot be resolve. For example
ping 216.239.61.104
ping www.gogle.com
both work fine, until I try,
ping http://www.google.com
it give me error, tell me that the hostname cannot be resolved. I tried to config my network using both dhcp or fix-ip, but the problem still present in both way. Internet works fine in windows/ubuntu.
Anyboy has any clue ? The router I use is wrt54gl with tomato firmware.
thanks in advance.

kowalski wrote:
Hi,
if pinging www.google.com works then dns resolving _does_ work. Why would you want to ping http://something?
You should try opening http://whatever in a browser not pinging it from command line.
Or am I missing something obvious?
Yes, for instance, all mirror list for pacman is in "http://...." or "ftp://...." form. I could easily change the repository list, but I'm not sure if it'll have same problem in future with other program. Also, if it work in ubuntu and windows, why not arch.

Cannot Telnet to Server

Dear all,
I have a problem telnetting to a Solaris 10 server (sunFire V240) after it reboots.
If I do an svcs -a | grep milestone
It tells me that the muti-user and multi-user-server processes are running. I did notice that the multi-user-server did not always start during start up.
I tried to do an svcadm enable -r svc://milestone/multi-user-server:default
but, it took a long time for it to come into the "ONLINE" state.
The strangest thing is this: I can ping, but I cannot telnet into the machine.
I did an svcs -a | grep telnet and the telnet process is running. (obviously, i checked that before).
Now the current state is this:
I can telnet FROM this server to other servers, but I cannot telnet from this server TO other servers. I always get: "Connection Refused"
Has anyone else here been in this situation? I'm new to svm, and perhaps I'm missing something? I read all the manuals I could find, but still no luck.
Please, if you can help me, I'd really appreciate this as this server's state is causing me a lot of problems.

Out of curiosity, I'd like to know something also:
when doing an svcs -a | grep milestone, the server tells me the following:
online svc:/milestone/name-services:default
online svc:/milestone/devices:default
online svc:/milestone/network:default
online svc:/milestone/single-user:default
online svc:/milestone/sysconfig:default
online svc:/milestone/multi-user:default
online svc:/milestone/multi-user-server:default
I'm just curious,but how is it both single-user AND multi-user-server BOTH can be default?? I specified that I want the multi-user-server to ALWAYS be the default for when an init 6 is issued, and I'm not entirely sure the machine has respected my wishes.
Have I misunderstood the above concept of what the svcs -a is producing, or is my Solaris 10 server not behaving normally?

Cannot Telnet back into standby ACE after upgrading to V4(2.1)

I am in the process of upgrading from v3.2.5 to v4.2.1, i have been follwing the upgrade/downgrade guide forv4(2.0) for my redunanant pair of ACE 4710.
everything ok, following procedure after the standby is reloaded and comes up to standby-warm, Iget the license incompatabilty message on the primary.
but I cannot telnet back into the standby, i can ping it ok though.
I am loathe to go any further, and do the 'ft Switchover all' and reload the primary incase I cannot telnet back into the primary when it comes back up.
Is this a known problem? whats the fix?

Hi, I have a similar problem, when I want to telnet to the ACE sometimes does not work, can you tell me how can I give to the admin context more resources?

Just installed dual band router/wifi, cannot log into Apple ID.

I just installed a new dual band router/wifi and now i cannot log into the Apple account on my Apple TV. I tried restarting the computer, Itunes and apple tv, still no luck. My apple tv is connecged via the ethernet cable.

Hey katikapral,
The article linked below details a few additional troubleshooting steps that can help get iMessage successfully activated on your iPhone.
If you get an error when trying to activate iMessage or FaceTime
https://support.apple.com/en-us/HT201422
All my best,
Allen

I cannot get into my router setup using 10.0.1.1

I cannot get into my router setup using 10.0.1.1
I did ipconfig and got the address but cannot open it up to make it a server.

This sounds like you are trying to use a web page setup for the AirPorts, which will not work.
You are aware that you must use an application.....AirPort Utility.....on a Mac, PC or iPhone or iPad to set up and configure the Airport routers, correct? The Setup Guide is pretty clear about this.
Is this a new AirPort Extreme that you have? If yes, please review the System Requirements:
Setup and Administration
iPhone, iPad, or iPod touch with iOS 6 or later and AirPort Utility 1.3
Mac with OS X Lion v10.7.5 or later and AirPort Utility 6.3
If you have a previous version of the AirPort Extreme.....and you have not downloaded and installed AirPort Utility 5.6.1 for Windows - Support - Apple , now might be a good time.

My Router Is Definenetely not working right and i cannot sign into it

I really need some help guys! I have a WRT54G V.2 and today we reset our IP address which messes it up. First of all I am not sure how to fix this but i cannot get into my router to do it with instructions. Some people told me i need to update the firmware and i cannot do that either. Anytime I type 192.168.1.1 all I get is this page cannot be displayed. This is extremely annoying and I really need to get my router up and running ASAP!! If anyone has any ideas or can help in anyway I thank you in advance!

HTMLGEEK,
there are 2 things you need to check..
1st - are you getting an ip address?
2nd - can you ping the router?
if you have both then try resetting the router for 30 secs. then after resetting, try accessing the router page again.

Linksys Router cannot communicate with DNS Server

Hi,
I have a RCA cable modem and a Linksys router and I have been having problems connecting to the Internet wirelessly. When I connect directly to the modem I can get on the Internet (but the connection does seem a little slow). On another forum I was told to disconnect the power from the router, wait a minute, then disconnect the modem and disconnect all wires. Then plug in modem and let it boot, then plug in router and let it boot. This does get my wireless connection back, but then after a few hours I lose it. My Internet provider Earthlink/Time Warner says that the router is the problem, but they see that the router gets a valid ID address, but it cannot connect to the Primary DNS Server. When trying to connect wirelessly I either get the message “Cannot connect to primary DNS server” or “Cannot connect to DNS Server 207.69.188.185”.
I don’t know if my Linksys router is shot or if the problem is originating from the modem. Any help would be greatly appreciated.
Thanks!

Whats the Wireless Settings you have setup on your Router?
This might be due to the default wireless settings set on your Router, login to the setup page of your router and below change the wireless settings on your Router.
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbors network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...
Now see if you can locate your Wireless Network and attempt to connect...

WRT54G behind another Linksys router

the WRT 54 is donated and we are trying to expand to cover more computers from our original 8 pport Linksys rouoter and add wireless. Plugged the WRT internet into a port from the original router and it shows the IP address as 192.168.1.1xx for each of the additional computers we hook up with ethernet and the wireless IP is also of that sequence for IP addressing. But we cannot get to the Internet. The WRT 54 as a stand alone router works just fine, ethernet and wireless Internet connections. Is there something we need to do to set up the WRT to work behind the other Linksys router.
Message Edited by sechrist on 10-29-2009 06:56 AM
Message Edited by sechrist on 10-29-2009 06:56 AM
Solved!
Go to Solution.

see here.

Windows host cannot establish Ethernet link to Arch Router

This is a weird problem.
I have a Windows host about 20 meters away from my Arch Router, the Ethernet cable goes into the wall, with wall sockets, so it's a total of 3 cables (1 in wall, 1 @ router, 1 @ host). I've tested the Ethernet cables with a LAN tester, they are all fine. When I connect the host to a Linksys router using the same cables, an IP address is obtained and the link is up and running.
But when I connect the host to my Arch Router (an Arch computer with some network cards), no ethernet link at all is detected. No lights on the ethernet card of the host, and ethtool on the router reports the link being down. I have connected my laptop to this ethernet card of the router and it works just fine, I get an IP and I can surf the web etc.
I really have no clue why this other host cannot establish a link. Does anyone have a clue what the problem might be?

pyther is right. Check for Auto-MDIX support on your network cards.
What network cards are you using?
Rule of thumb:
Auto-MDIX is a requirement in the Gigabit Ethernet specification, so proper Gigabit capable cards will work 99% of the time whatever cable you use.
Fast Ethernet (100mbit) and below does not have Auto-MDIX in it's specification, so those 9 out of 10 of those cards will not perform it! When connecting these directly to another network card, use a cross-cable.
Also make sure the network cards are in working order. I assume the ArchRouter PC's network runs fine when you connect that to your Linksys router?

I cannot telnet into my WRT54GC linksys router

Similar Messages

Maybe you are looking for