I CANT GO INTO BIOS! SLI PLATINUM! I INSTALED WINDOWSXP AND WORKS GOD
Hello!
I have MSI SLI Platinum.I bought it on **SPAM**. I cant go into BIOS but Windows works (I innstaled it), 3DMark05 run god.
I update bios from 3.7 to 3.9 and nothing! SelfPost OK, BootMenu OK, but when I press DELL and BIOS don`t start only display in top left one line.
I change my config (RAM, GPU, CPU) dont help. Windows still works, 3DMark05 to.
What happend??
jimi85 (Polnad;)
Quote from: jimi85 on 24-March-06, 18:44:30
I press DELL
See there is the problem...
Similar Messages
-
installed adobe flash 13 and i cant watch any videos i uninstalled it installed it and the f-ing adobe pagesays its missing a plug in and im looking at the plugins and lo and behold its plugged in and i downloaded mavericks about a week ago the funny thing the game i play on a igg website works just fine but when i want to watch a video it plays 18 secs and quits
You may need to revert to a prior version of Flash > Adobe Community: ATTENTION MAC CUSTOMERS - Flash Player 13 "Plugin Failure" Workaround
-
Unknown Processor Revison & Cant get into bios! RS482M4
Similair to problem to another post but have tried what was suggested.
This is my first attempt at an AMD system and I've hit a dead end on the first switch on...
AMD Athlon 64 3700+
MSI RS482M4 Motherboard
1GB RAM
WD 1600AB H/Drive
Sony CD-RW
When I power on I get the bios screen with the M/B details (RS482M4 A7019AMS V1.1) and processor details (AMD Athlon 64 Processor 3700+DRAM Clocking = 400 MHz).
It then goes a little further, initialises USB drivers, mememore HD and CDRom then states:
CMOS Settings Wrong
CMOS Date/Time Not Set
****Warning: Unknown Processor Revision ****
The processor installed on your system is of an unknown revision. Please contact your BIOS vendor for appropriate upadates.
Fatal Error ... System Halted.
I have tried resettng the CMOS but as I cant get into the BIOS I cant update it and feel like I've been going round in circles for the last 5 hours!
Any ideas?Bios version is V1.1 and PC doesnt boot to anything - doesnt get beyond saying 'Unknown Processor Revision' to even allow you into the bios to try updating it.
I have also tried asking on the MSI online support but as yet with no reply. Its really annoying me as the motherboard has all the things I need and don't want to have to go and buy another one (have tried the CPU & memory in another machine and all worked fine). -
P6N Sli Platinum front audio panel and CPU temp voltage issues
Hi All,
I got my P6N Sli Platinum yesterday, build up my computer without any major issues. However I have noticed that my audio front panel does not work. It could not detect my microphone when i plug it into front auido panel, it works fine for the rear auido panel though.
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
Finally, any tips to max the overclock potential of this board? I have overclocked to 3.1g but there are some crashes. Going higher the board just won't boot up. I read a review on anandtech.com says 1.22 bios is good for oc. Where can i download that? I only found 1.1 bios on official site.
Any reply will be appreciated.
CheersQuote
Another issues is I highly doubt the accuracy of CPU temp sensor. Msi 's software monitor reports my CPU temp is around 19-20 degree, I know that's too good to be true even I am using a water cooling system. Btw my cpu is E6600. Anyone else has the similar issues?
C2D-CPUs have a digital internal sensor to monitor CPU Core temperatures. Have a look at those with Core Temp ( http://www.thecoolest.zerobrains.com/CoreTemp/ ). This Tool reads the temperature data directly from the register of your CPU. There is nothing wrong with the sensor. It is rather the MSI tool that does not read the data it provides correctly.
Quote
The third, I notice my CPU voltage is bouncing between 1.1 to 1.24 in CPU-z. And the multiplier is changing from 6 to 9, frequency is changing from 1.6g to 2.4g. I only see this in CPU-z. Msi 's own software reports CPU running at 2.4g though. Is this cpuz issue or something else?
There is no issue. What CPU-Z allows you to see there is the C1E-feature of your CPU at work. When there is nothing to do your processor will automatically reduce Core Voltages and frequency to save power and keep temperatures down. As soon as the work load increases the multiplier is set back to x9 and core voltages increase dynamically. It is meant to be a good thing.
I have overclocked my system a little and I like that the C1E feature is still working at this speed setting CPU frequency to 2GHz and core voltage to 1.144v when my system is idle.
If you have problems with this feature you can turn it off in BIOS. The option is labeled as "C1E Support" and might be hidden somewhere. You may be able to hit "F4" to unhide it.
The MSI utilities are not the best tools to monitor your system. CPU-Z, Core Temp, Everest, Speedfan, Memset, Rightmark Memory Analyzer for example do a far better job. -
K9N2 SLI Platinum - new Phenom support and OC
____________E D I T ___________________
MSI K9N2 SLI PLATINUM
SUPPORTS
AMD PHENOM X2 965 BE CPU
____________E D I T ___________________
if it didn't I would be crying in a corner somewhere not posting this from my super fast PC
Thanks to all you guys
____________E D I T ___________________
Hi guys,
Had my lovely new M/B for a few months now and It has been a wonderful board.
despite one hiccup where the PCIE bus had a moment / died ( flashing the BIOS to latest fixed it )
My setup currently :
Jeantech Storm 700w Modular PSU
MSI K9N2 SLI Platinum
AMD Phenom 9550
with Zalman silent fan
4GB crap ass RAM (that's a real brand .. honest)
2 x BFG 9800GTX+OC in SLI I likes these .. they make lovely noises in my dark room .. VrrrrUmmmmmmm mmm mmmm mmm
500 GB slow ass HDD (Again the marketing dept of this brand were out to lunch when they launched it)
Windows 7 RC. latest build
Nvidia Det's 190.xxx latest driver
mostly playing Fallout 3 (graphics are beautiful but notice the CPU is lagging behind now)
So to the Crux of my issues :-
I'm looking to upgrade a few things here though,
as you can see a few components are severely bottlenecking performance.
First off the RAM.
going to get some nice Kingston 1066 DDR2 (4GB or should I go for 8GB ?)
next .. a WD VelociRaptor 10k rpm HDD probably just a small 74GB or the 150GB drive
and finally the pies de resistance ( yes PIES ! .. I like PIES !!) shiny new AMD Phenom 965 CPU
SO... Will the 965 phenom work in this board ? I've logged on tech support but no answer,
latest BIOS is installed already 7374v35 i think.
I know it's a 140W CPU so okay there,
the Socket AM2+/AM3 is good
.. I just NEED to be sure before spending £200.00
if not .. is it worth getting the 945 or 955 BE and clocking them ... could the board handle clocking the 965 ??
and last of all, if any one has any opinions on the build .. let me know... have you built a similar rig ?
cheers all
PIES out ~!
OCDWoW !!
Thanks for the replies guys, I really appreciate it...
and after a drunken bout of spontaneous cash wastage on the internet last night :
1) AMDOA06KNF PHENOM II X4 965 £151.07
2) WDGA060T2 WD VELOCI RAPT 150GB £99.07
3) KTEA069M4 4GB 1066MHZ DDR2 £41.70
... goods on the way...
So I guess in a few days I'll be able to update you all on the build and will more than likely be updating this post with my random moronic questions and queries when the next thing goes wrong
looking into Power requirements
9800GTX+ SLI requires a min 550w PSU .. and so far in top gaming and 3D benchs hasn't gone over 250w on the meter ( pretty good I think)
the Zalman CNPS9700 LED seems to keep everything cool without any power to the fan... but I leave power on low just for the pretty blue lights
I'm happy to listen to any advice though,
One thing I will need is any pointers you can give on the K9N2 built in OC facility in the BIOS .. is it any good .. can I TRUST it to not fry my CPU by running it on auto ? is there any recommended settings ? etc. your thoughts and experiences welcomed
OCD -
MSI P6N SLI Platinum- Wake on Keyboard Not working
Minor issue...... but the wake on keyboard is not working consistently. I still have version 1.0 of the bios. I can set it in the power management and it works! maybe once..... then nothing. Works again (once) when you reset it. But doesn't consistently stay working! I have a USB mouse, so the wake on PS2 mouse isn't happening.
Any thoughts?
It's not a huge issue but I would like the bios options to be working as it looks like they were intended. It's just different in that my last 3 machines I could turn on from hitting a key on the keyboard and not having to get the power button on the case. I'm using the same Microsoft corded keyboard that was working for this on the last build.Quote from: uzzi on 02-May-07, 11:52:23
No I have the SLI MB, this web site was from a MSI tech, the web site is ftp.msi.com.tw/ with not only all the BIOS files but the most updated divers. I could never find these files on their web site before. Here's the web site for the MS-7350 MB ftp://ftp.msi.com.tw/BIOS/7350/.
I did get it resolved with the wake on S3 Mode, you know hit any key. Here's the test to tell if your MB is good or bad. The easiest way is go into BIOS and turn on your number lock, make sure the light is on your keyboard, also make sure your bios is in "S3" mode w/hit any key option on. While in bios turn off your PC w/the case PB, does your number lock light stay on? If it does, your PC will boot-up. I can repeat this over and over. If you get the same results, the next test will be the last. when you turn the PC off in Bios, and the number lock light stays on, switch off your power supply, and wait about 10 sec. and then turn your power supply back on, if your keyboard number lock light never came back on, your "S3" mode on your MB is BAD according to the MSI tech. I like this MB, but it's time for a RMA. I hope the next MB wakes up right.
Uzzi
Uzzi, Did what you suggested and the light stays on when turning the PB off but then turns off and does not come back on when the power supply is cycled. I sent in a tech support request to MSI Tech. Did they tell you to RMA it? I guess I could send it back to the Egg for replacement..... but hate to keep eating shipping costs! -
Cant get into BIOS via DEL key, screen goes blank on load RD240
Hello group, having an issue with a RD240 rackmount server attempting to bring it online for the first time. Currently in a one CPU configuration with one stick on RAM in the correct slot, using SAS. When the computer first boots prompting you to hit either DEL or TAB those keyboard commands are non-effective. Once it bypasses that screen it will move towards the LSI connfiguration utility. If you hit Ctrl +C it will say that the utility will become active after initialization. The screen then just goes blank. At that point I can hit Ctrl Alt Delete and it will reboot the server and then in the same mess again, Del is ignored, I can't boot off the CDROM, cleared the BIOS using the jumpers, nada. Any thoughts on this would be great, at this point I can't get in to configure and if I just let it boot always ends in a black screen. Checked the cables for the SAS and everything looks good across the board to me. Tried different RAM sticks, unplugging the SATA CDROM, etc. I can get into the Mgmt via the web and sensor show everything green across the board etc but something is borked. There is a LED screen on the mainboard with the number 78. I couldn't reference what that means. All drives I can hear click on, Cheetah 15k all around. Steady green light on bottom, top light out. Any input would be greatly appreciated!
Try pressing F1 at the Thinkserver Screen. When Setup Bios appears, you can exit out by pressing Esc. After the screen goes blank, press Ctrl+H to get the Web Bios screen which will allow you to configure your server. I hope that this will help.
-
Cant get into Bios, New board (K8T Neo-FIS2R)
I just put in a new board and cpu, everything seems to start up fine. BUT I press DEL to get into the bios settings and it tells me theres no bios installed. My HDs wont autodetect at the start so i havent gotten to windows yet, HD taken from old pc with winxp on it already.
Im totally lost here as what to do.
Can i just DL the newest bios drivers and flash?Quote
no bios installed
...that's the Promise controller...you have to press Delete when you first power on, you're probably missing the timing because of the Core Cell screen...
...you don't want to flash the BIOS until you get a stable system...well, you could, but... -
Cant get into bios after P965 NEO MB change..pls help
hi all, i just changed to the MSI P965 NEO, when i power up, all i get is the MSI start up utility asking me to press either "tab" or " del" , i pressed but nothing happens..
Can someone please help me out?..thanksQuote from: accuwipe on 02-December-06, 23:34:15
alrite alrite...here it goes.
Model RS-380-PMAR (Non-PFC (Regular))
RS-380-PMAP (Passive PFC)
Type ATX Form Factor 12V V2.01
Input Voltage 90~140V / 180~265V (Selectable)
Input Current 8A @ 115Vac / 5A @ 230Vac
Input Frequency Range 47 ~ 63 Hz
Fan Sleeve bearing 120mm fan
Power Good Signal 100 ~ 500 ms
Hold Up Time > 17 ms
Efficiency > 70% typically
MTBF >100,000 hrs
Protection OVP / OCP / OPP / Short Circuit Protection
Dimension Standard ATX 150 x 140 x 86 (mm)
Operation Temperature 0~40?
Safety Nemko / TUV / cUL / CE / BSMI / FCC
whats needed
< name brand >
+12v1 = ?
+12v2 = ?
+5v = ?
+3.3v = ?
if your psu doesnt have 12v 1&2 then list the +12v = ?
theres your problem, no futher testing till your power supply has been replaced!
24 to 30 amps on a SINGLE 12v rail power supply needed, and name brand / not generic. -
MSI P6N SLI Platinum, Dual Core Center and Mem Voltage
I set my memory voltage for my Corsair sticks to 2.0 just as TheRamGuy at Corsair's House of Help forum had suggested. However, in Dual Core Center, it reports that the Memory voltage is at 2.7!!!!.
I seem to vaguely remember some threads somewhere in one of the forums about the MSI boards frying higher voltage memory, and so am concerned to say the least.
Or is there a better program that can display the Memory voltage?? Or do I believe the Dual Core Center readings?Quote from: NovJoe on 13-April-07, 16:01:41
CPUID would let you know if your RAMs are running at the correct timings.
You can try SisoftSandra or Everest to check on the detected voltage in Windows.
OK, I've downloaded both SiSoftSandra and Everest. I don't see anywhere where these programs report/measure a memory voltage. One one screen, it will report on the SPD settings for the memory and lists the rated RAM voltage "setting", but not the actual juice going to it.
Oh, well. Must just mark it off as one less thing to worry about -
Both towers are 2009 models, one is 8-core, the other 4. I figured the problem was with the power supply, so I just stuck the guts from the 8-core into the 4-core. It booted up with no issues at all, didn't require any updates or anything. Firefox even restored my tabs. But after about 5-10 minutes, the machine shut off at random and won't start back up. The DIAG LED lights up one LED yellow when pressed, labelled "5V STBY". Same LED on both boards.
Any ideas? I've got two really expensive paper weights at the moment, and my AppleCare plan expired 3 months ago.Dust VAC for dust bunnies
real issue can be thermal paste or lack or needing redone
dust clings to any ram or electronics or inside psu and graphic cards
motherboards both support dual processor?
thermal sensor readings from Hardware Monitor would be nice
unplugged is not enough to reset the SMC, power on button also, and every cableetc disconnected
try with one dimm too -
Macbook Air locks up as soon as you click on anything when turned on. Can't update software, can't do anything. Help please
To rule out software probem, do the following:
Run OS Recovery
Disconnect all devices from your computer.
Boot up from your computer by holding down the command+r keys. This will take you to the recovery drive.
Select Disk Utility & hit Return.
In Disk Utility select the HD on the left & click on Repair Disk (bottom right).
When you reach the desktop after doing the above, repair permissions & restart your computer.
To rule out hardware problem:
Run Apple Hardware Test. -
i have a emac 1002 emc 1955 that wont go pass loading screen and cant get into utilities,i got from a auction and dont want to take it apart if i dont have to so looking for a little help before it goes that far.thanks
Hi Mike, the Keyboard shouldn't matter, it should be OK in that respect.
Your kind of stuck without any Install Disc to try to repair it or reinstall, but...
Tough without the Install disc, but some things to try...
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).
Resolve startup issues and perform disk maintenance with Disk Utility and fsck...
http://docs.info.apple.com/article.html?artnum=106214
Tough without the Tiger Disk problems, but try fsck...
To use fsck, you must run it from the command line. Unlike using your mouse to open an application to do something, you'll need to type a text command at the prompt (#) to tell fsck what to do. The Terminal application (/Applications/Utilities) and single-user mode are two examples of command-line interfaces in which you can type such commands. To use fsck:
1. Start up your computer in single-user mode to reach the command line. Hold CMD+s keys down at bootup. Note: If necessary, perform a forced restart as described in the Emergency Troubleshooting Handbook that came with your computer. On desktop computers, you can do this by pressing the reset/interrupt button (if there is one) or holding down the power button for several seconds. On portable computers, simultaneously press the Command-Control-power keys. If your portable computer doesn't restart with this method, you may need to reset the Power Manager.
2. At the command-line prompt, type /sbin/fsck -fy
(SPACE between fsck AND -fy important)
3. Press Return. fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
The volume (name_of_volume) appears to be OK If fsck found issues and has altered, repaired, or fixed anything, it will display this message: ***** FILE SYSTEM WAS MODIFIED ***** Important: If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
4. When fsck reports that your volume is OK, type reboot at the prompt and then press Return.
http://docs.info.apple.com/article.html?artnum=106214
Then Safe Boot, (holding Shift key down at bootup), & use Disk Utility from there to Repair Permissions, reboot once more.
Then Safe Boot from the HD, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
Does it boot into Open Firmware with CMD+Option+o+f ?
http://docs.info.apple.com/article.html?artnum=42642
reset-nvram (press Enter)
set-defaults (press Enter)
reset-all (press Enter)
Have you done a PRAM reset, CMD+Option+p+r...
http://docs.info.apple.com/article.html?artnum=2238 -
MSI P7N SLI PLATINUM 750i Wont Power UP!!
i have an MSI P7N SLI PLATINUM 750i which was working perfectly but one day it just wont power up for some reason. my configs are
MSI P7N SLI PLATINUM 750i
Core 2 Quad Q9550
MSI Nvidia 8800 Ultra HD OC
4 Gb DDR2
1T WD HDD
PSU 750W Cougar
i have tried every thing clean the pc,changed every thing but it still wont power up i tried another board with the same configs and it powers up just to make sure the problem is in the MB The red light on the motherboard stays on thats means there is power running thorough the MB. it still under warranty but the problem is i can reach the MSI HQ here in egypt to fix it or change it so any ideas?well i have reported my issue to MSI Customer Support exactly like that:
Quote
i have an MSI P7N SLI Platinum / P7N Zilent which was working perfectly but one day it just wont power up for some reason. my configs are
MSI P7N SLI Platinum / P7N Zilent
Core 2 Quad Q9550
MSI Nvidia 8800 Ultra HD OC
4 Gb DDR2
1T WD HDD
PSU 750W Cougar
when i press the power button nothing happens.its still under warranty but the problem is i can reach the MSI HQ here in Egypt to fix it or change it so please advice about the name and the location of the MSI HQ in Egypt and notify them about my situation and to contact me regarding my problem
so do u think that they will replay and advise about the issue? -
New K9N2 SLI Platinum isn't booting into BIOS
So i just built a new system with an MSI K9N2 SLI Platinum, and installation went by with a breeze. However, after supplying power, and turning the system on for the first time I'm met with absolutely nothing.
I'm not the most advanced in this category, and I've certainly never experienced the likes of this ever. I've gone through the hardware configuration a thousand times, and I'd know if it were that.
I was wondering if anybody knew a few tricks to get this new board to boot. I'm suspecting it's probably something small and obvious I wouldn't ever think of.
But yeah, any help would be much appreciated.
Current System:
Mobo: MSI K9N2 SLI Platinum
CPU: AMD Phenom X4 9850 (black edition)/stock cooler
RAM: Corsair Dominator 2x2048Mb 1066Mhz DDR2
GPU: PNY XLR8 GeForce 9800 GTX
HDD1: Western Digital VelociRaptor 300GB 10K RPM
HDD2: Seagate Barracude 1.5TB 7200RPM
No operating systems yet (which is kind of impossible since I can't even set the boot order without the BIOS loading.) But I plan to run XP Pro alongside Gentoo.All fans are spinning fine, I'll get the PSU info later, I took it from an old system I built before my last deployment. It's an 850 watt (single 12 volt rail) system, not sure the exact specs on it anymore.
I do believe though, that I've managed to knock something loose as it keeps beeping repeatedly now when it boots. Before it was absolute silence on boot. (which is weird because i don't actually remember installing the speaker?)
Oh, the DVD drive is from another system too, and pretty old, but it opens, and functions.
I also swapped between onboard video, and the graphics card to see if it was maybe the graphics card and still nothing.
Though I have to use a DVI converter with the graphics card (which is pretty lame for a 200+ dollar graphics card to have two DVI ports and an SVID port, but no HDMI port.)
Anyway, I originally tried to boot with my 1080P television connected into the HDMI DVI* port for the mobo.
Keep good language in a forum!
Now if I can just figure out what was wrong in the first place eh?
It seems the reset button allowed it to boot into the BIOS, but a regular boot wont?
Edit: Still wont boot into BIOS or POST though, I'm met with a blinking line that's been there for over 10 minutes now.
Maybe you are looking for
-
How to use a counter to build a Logic Analyzer?
Hi guys, i have heard that we can use a counter as a Logic Analyzer based on an incoming signal and its clock frequency. Anyone know how this works? I am trying to read a set of signals, which I have no knowledge of except that there would a Clock,
-
OK folks, I've done a stupid thing. To nake a long story short, I re-installed Tiger via Archive and restore, twice, but I mistakenly let it set up my primary user account under my personal name, forgetting that previously I had set up my business na
-
Enabling layer object outlining on object like CS5?
Is there a way to enable layer selection by locking the object? Example, in CS5.5 when you selected on an object (say a text box inside a circle) it would automatically select that layer so you an move it. IN CS6 you have to select the layer from the
-
HT4623 How can I download iOs on my iPad?
How can I download iOs on my iPad?
-
Pattern or beat editor for drums
How do I use Ultrabeat's pattern editor, but use BFD as the software instrument? It doesn't need to be Ultrabeat, but I'd like to be able to have a pattern editor or beat editor as the interface, but use BFD for the sounds. I can sorta do this with B