I changed routers- mg3200 will not print. cannot find cd. HELP!

I changed my router. How to do link my MG3200 into the printer. I cannot find the CD that came with the printer, and I cannot find the usb cable either.

Hi hittingguru,
You will need to reinstall the drivers on your computer to reconnect the printer to your network. You will also need a USB cable to perform the reinstallation. If you need to obtain a USB cable, they can usually be purchased from most retailers that sell computer electronics such as Staples, Wal-Mart, Target, Best Buy, Radio Shack and Amazon.com. You will be looking for an "A to B" USB cable.
Since you do not have the installation CD, the latest drivers for the printer can be downloaded from the Canon USA website. So we can provide you with instruciton for downloading applicable drivers, please reply with what version of Windows or Mac OS X is on your computer.
If this is a time-sensitive matter, additional support options are available at Contact Us.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Similar Messages

Canon ip4700 amber lights blink 5 times will not print, 4 years old, help please

Canon ip4700, amber lights flash 5 times, printer will not print, any advise appreciated

This issue has been resolved - my Support Advisor, Edgar, was able to discern what was causing the problem.
It appears that, despite years of never experiencing this, one of the latest ipod updates actually altered my device's personal settings and changed it to "Manual" for all synchronizing; even performcing Factory Restores did not change it back to being automatic.
My ipod is working as good as ever now thanks to Edgar. If anyone else is having this problem, please make sure you check your device's settings in iTunes and see if "Manual" is checked - even if you never changed the settings yourself and have no reason to suspect that to be the problem, as was the case here. If it is checked - uncheck it to enable automatic syncing.
So relieved this was not a much more serious problem. I've missed having my music on the go. Thanks, Edgar!

2 weeks ago, Firefox changed. It will not print graphics in a web page or show them in print preview. It also does not provide the ability to select options in "print forms". they are now grayed out.

I am using www.investools.com
It prints the graphics in the normal page fine
but when I switch to prophetcharts, which loads javascript, the graphs do not display or print.
The text on the left side of the display show but graphs do not, even when I reduce printing size to 30%.
I am using an HP 8500 Pro Officejet.
Everything works in IE fine (but I don't want to use IE).

Hi ArielAce , thanks for getting back to me!
I would recommend downloading and running the HP Print and Scan Doctor.
Please keep me posted!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

H.P.ENVY4500 WILL NOT PRINT UNLESS WIRED CONNECTION IN PLACE

Have just purchased H.P. ENVY 4500 and connected to computor using WiFi-no problem.After connction found it would not print from documents etc.Tried to install disc but this would not start so whent into H.P. website for installation.this installed but then said could not install over network.I'm not very techy so this has me baffled.Then decided to wired connection between printer and computer and this works ?? Wife has a laptop using WiFi and printer responds to this just using WiFi.WHY?? Very grateful if someone can give me some idea as what to do.Many thanks.

Hi @KIP7,
Welcome to the HP Forums!
I understand that your HP Envy 4500 will not print on a wireless network, and I am happy to help!
For further assistance I will need to know: If you are using a Windows or Mac Operating System, and the version number. To find the exact version, visit this link. Whatsmyos.
In the meantime, I would suggest to go through this printing guide. Print Jobs are Stuck in the Print Queue. As it addresses the fact that the printer will not print.
Hope this helps, and hope to hear from you soon!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Downloaded acrobat reader 11 onto my Mac Book Pro, it can open the file but will not print. Get a message that says PDF cannot be printed, however, I forwarded it to someone else and they could print it, no problem. I called HP and spent an 1hour with the

downloaded acrobat reader 11 onto my Mac Book Pro, it can open the file but will not print. Get a message that says PDF cannot be printed, however, I forwarded it to someone else and they could print it, no problem. I called HP and spent an 1hour with them and then called Apple support and worked with them for 3 hours. No one can figure it out. Is there something wrong with this version? the pdf was created in 2004. Do I have to pay to get Acrobat?

Let me give you a slightly different perspective than everyone else here. You are using an unsecured wireless network, which means that all your network traffic is easily available for viewing by anyone else using that network. That's bad. Very bad, for you, unless you absolutely trust everyone who lives within range of this network. So stop doing it.
As to the Mac not connecting, wireless networking is simply too complex for any reasonable answer without more information. There are many possible error points, and as often as not it's the Mac that can connect and the Windows PC that cannot. Since you can't give us any information about the configuration of the neighbor's network, and can't make any changes to it, we can't do much to help you troubleshoot it.

Canon mg3200 will not align correctly prints is blurred

Canon mg3200 will not align correctly prints is blurred. I have used the canon print head alignment several times. It will print some of the picture correctly and the rest is out.

Hello,
Please try the procedures outlined in the link below:
http://kbsupport.cusa.canon.com/system/selfservice.controller?CONFIGURATION=1011&PARTITION_ID=1&secu...
If the issue persists at that point, the best thing to do would be to get in touch with our technical support team at http://bit.ly/Phone_Support for further assistance.
Thanks!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Windows 7 64 bit, changed wireless modem, now c4500 all in one will not print.

I had to have my wireless modem changed and now my 2 laptops will not print. 1). windows 7 64 bit. 2) windows xp, version 2002 service pack 3. The new wireless modem is from ATT u-verse 2wire892. I tried reinstalling on the windows 7 laptop and it tells me can't be installed on that operating system. I had it there before. I ran a Wireless Network Test Report and under the network name it still has the old net name not the new one, how do I change that?

Found diagnostic utility at hp support. Though I lost all jobs in the queue, printer is again working. YEAH!

B210a will not print after changing router\modem

b210a will not print after changing router\modem. Says it is connected to network, but will not print and says unavailable

Good morning,
Please use the second section of the following article to fix:
http://www8.hp.com/au/en/campaigns/wireless-printing-center/reconfiguring-system-help3.html?jumpid=r...
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

HP Photosmart 6510 series network printer will not print black after changing cartrage

HP Photosmart 6510 series network printer will not print anything that is black or has black in the picture after changing cartridge, all other colors are working properly after changing. Does not look like any damage to the cartridge or the insert where you plug in the ink. The well where the ink pad and the cartridge meet is damp with black ink. So not sure what is going on

Hello dinger57 and welcome to the HP forums!
I understand since changing the black cartridge the black ink has not been printing. I'm sorry to hear this, but I will definitely do my best to lend a hand
I will suggest that you start with following through this Printer Does Not Print Black Ink or Color Ink, or Prints Blank Pages document. If the issue persists after that can you please let me know what country you're in and whether the printer is in or out of warranty? Thanks! Please feel free to private message me the country information.
Hope to hear from you soon!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

HP ENVY 5530 will NOT print in win 8.1

New HP ENVY 5530 wireless printer bought 2 days ago. Will NOT print a single document in Windows 8.1. It's scanning perfectly, I can also print from my Android HP eprint App perfectly. The printer is showing as connected and working properly (as evidenced by printing ability from other device).
The printer acknowledges I'm trying to print a Word doc, the printer message box, when clicked, shows me the document has been sent to the printer yet it sits there for about 3 - 4 seconds then ...DISAPPEARS and no document comes out the printer.
I have done everything I can think of....And, looking at the printer properties, it seems to have created its own dedicated Port which shows as "WSD...long number etc" Please help. Thanks!

UPDATE: I am utterly discouraged, frustrated and pretty annoyed now. Windows 8 and 8.1 are obviously the cause ofserious issues with HP ENVY 5530 (and other HP printers!) I have been on the phone since 11/26/13 and spoken to no less than 6 different people, one of which was a supervisor (Jay) at the HP Total Care Tech Support dept. My issue has slowly been escalated to the Lead Stream Dept. which was of no concrete help! I just got off the phone with one of the engineers (name: Sanal, in India) and he could not resolve the issue ater uninstalling, reinstalling and cleaning up the registry, checking the spooler etc etc. His advice was to call my ISP Comcast and get them to change the 'channel' to 11 as the printer works best under channel 11....?!?! WHY? I am not about to include another party to add to my issue! I think I need to take this printer back and buy one that I have researched and know for a fact works perfectly under Win 8.1!!!! I am so angry at this minute! How is this in god's name possible not to have a patch for this APPARENTLY COMMON issue your HP newer model printers are having with win 8 and 8.1??? I was reassured each and every time the issue would be resolved during each and every call I made! No one can resolve the inability of the printer and laptop to communicate. It shows are connected, online, functioning, is set up and installed properly.... it will scan, copy and even print docs from my Android YET NOTHING will print not even a test page from my Acer Laptop which is less than 10 months old!! HP scan doctor cannot figure out what is wrong either. Its test page does not print, yet its INTERNAL test page printed just fine. SMH.....sigh.....

Photosmart 6520 e Windows 7 printer says it is connected to network, but will not print.

I've followed all suggestions in troubleshooting both from manual and on line. Shut off firewall, unplugged, plugged waited. Nothing changes. All printouts from the printer say connected, but will not print and computer detection of the printer says cannot be located. Help!!

Glad you were able to find the problem. I am sure that the Print and Scan Doctor would have come to the same conclusion Thanks for sharing what the cause was...I am sure others will benefit from it if they also have this issue.
If I have helped in any way, just click the Kudos star on the left. Also, if your issue has been resolved, don't forget to select Accept as Solution

OJ Pro 8625 will not print in color only shades of gray

Printer was purchased two days ago. The printer will not print in color only black and shades of gray. alignment test on 2/28/15 showed color. cartridges show full.

Hi there @ChuckHilde
Welcome to the HP Community
I saw your post about how you cannot print in color, and I would like to refer you to try the steps I previously recommended in another thread. The printer itself prints in color, therefor there is most likely settings on your Mac that need to be changed.
Click here to get to that thread and try the steps: Re: Printer Only Prints Pictures in Black & White
You should be able to print in color after those steps!
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Times New Roman font will not print on HP Officejet Pro 8610

My new HP Officejet Pro 8610 will not print documents, spreadsheets, or printer test pages containing Times New Roman font (of any size). It does not put a job in the print queue. In Excel, I receive the "Generic_2_Q294552" error message. My setup: An HP Pavilion Elite computer NY809AV-ABA e9119t; running Windows 7 Enterprise SP1; HP Laserjet 5L, HP PCS 1310, and HP D4360 all print the font just fine. My new printer: HP Officejet Pro 8610, firmware revision FDP1CN1502AR, connected via USB cable. [Also connected via ethernet cable to cable modem.] What I have done so far to troubleshoot the last 3 days: Reinstalled the printer (3 times), the most recent today with an installer issued today; rebooted the printer; rebooted the computer after each significant change; updated the firmware in the printer; tried two different USB cables; tried printing the fonts in Microsoft Word 7, Microsoft Excel 7, and directly from the font file; reinstalled the Times New Roman fonts from backup; visited the forums and tried all of the solutions I could for any similar problem; tried the winprint, hpzppw71, and hpzpplhn print processors with both RAW and NT EMF 1.008 data types; found and repaired all problems I could find with any hardware and software, as well as updating all software to the latest version.

Thanks for trying to help. I am happy to report my experiments and results. Microsoft Word:I open a blank document. Type something in. Select the entire text. Change the font. When I change to some fonts (those listed on my DOES print) the document shows up in the print queue and prints. When I change to the other fonts (those listed as DOES NOT print) nothing happens. It just sits there. No messages. No crash. Nothing in the print queue. I can walk away for hours (as I have done) and come back and nothing has happened. When I change back to a DOES print font it prints. Change it back to a DOES NOT print font and it doesn't. Repeatable. Consistent. No configuration changes or installs have changed it. Microsoft Excel:I open a black spreadsheet. Type something in. Highlight the entire text. Change the font. When I change to a DOES print font it prints. When I change to a DOES NOT print font I get this: "Microsoft Office Excel Your file could not be printed due to an error on HP Officejet Pro 861 on 0. There are several possible reasons:. There may not be enough memory available. Try closing files and programs you aren't using.. If you use a network for printing, there may be a problem with the network connection or the printer driver.. There may be loose cables or a bad connection between your computer and printer.For more information about troubleshooting printing problems, chick Help. Show Help >>" when I click the Show Help >> button I get: "This error can be caused by:
General problems: The printer may be unavailable, the network may be down, the communication port to the printer may be corrupt or unavailable, a hardware error at the computer may have occurred (out of paper, paper jam, out of ink, out of toner, etc), and a language setting may need to be reset from the Regional Options control panel.
Local problems: There are several reasons for a local printer (a printer that is attached directly to your computer) to fail:
Check to make sure the printer has paper, ink, and/or toner and check the cables.
If the printer appears to be functional and a printer test by the printer itself indicates the printer is working properly, then check the cables, printer port from the computer, and configuration of the printer at the computer.
Occasionally, an application can develop a conflict with the printer driver and cause a memory leak which corrupts the printer port. If all else fails, restart the computer, recycle the power to the printer, and try printing again.
Occasionally it is even necessary to delete the printer driver and reinstall the latest version of the printer driver.
Network problems: There are various reasons for a network printer to be inaccessible: the name may have changed, it may be out of paper, out of ink, out of toner, down for maintenance, the network could be down, or a printer job previous to yours has stalled due to incorrect settings on the user's computer who last submitted a print job, or even your printer driver cannot communicate correctly with the printer. Network related printer failures are usually best handled by your local technical support.
Memory problemsn occasion, large print jobs with complex graphics or consisting of several hundred pages, which can consume large quantities of memory on the printer, may cause a problem (especially if there was an over run of memory at the printer). You may want to try reducing the amount of complex graphics in your print job, or break the print job up into smaller segments and see if that corrects your problem. It is not uncommon for a very complex graphic to have a defect or error which prevents it from printing on any printer. It may be necessary to load new or revised graphic converters or drivers in order to alleviate a problem of this type.
For more information about fixing problems related to printing, see Microsoft Windows Help and Support. (Click the Start button, and then click Help and Support.)" Excel keeps right on going. Doesn't crash. Just pops up the gray dialog box. Behind the box popped up is another box (that goes away then the dialog box is closed) saying: "Now printing page 1 of 1'Book1' on theHP Officejet Pro 861 on 0" The format of these messages does seem strange now that I look at it so carefully while trying to type EXACTLY what I see. I think I will try to shorten the name of the printer. Once again, Respectfully submitted for analysis, review, suggestions, and criticism. Tom

Officejet Pro 8600 - Macbook Pro and Macbook Air will not print

Products:
HP Officejet Pro 8600
Macbook Pro (Mac OS X, Version 10.7.5)
Macbook Air (OS X, Version 10.8.2)
Question:
Why did my Macs initially print fine, but now will not print at all?
Full Story:
I have a wireless network at my house that consisted of a 30mb cable internet, Netgear 900n, HP Officejet Pro 8600, 2 Dell Laptops with Windows 7, a Lenovo Laptop with Windows 7, and Dell Tower with Windows 7 - All printed just fine.
The HP Officejet 8600 was added to my network about 2 months ago.
I added a Macbook Pro and a Macbook Air about 3 weeks ago. Both Macs printed just fine for about a week. Then suddenly they stopped. I spent about 2 hours on the phone with HP Service, and they finally said it must be my router. So I called Netgear. Netgear was useless! They wanted me to agree to charges for services before they would even discuss the issue.
Due to information provided by HP's service support, and because Netgear will not support their product, I promptly purchased a new router - an Apple Airport Extreme.
The Macs recognize the printer, will print if hardwired via a USB cable, but will not print wirelessly to the Officejet Pro 8600. The PCs print fine.
The frustration that is being felt is compound by the fact that the Macs printed just fine with the Officejet Pro 8600 2 weeks ago, and now the printer just shows "idle"... even with a new router. (see image below)
Please help, I appreciate any support.
As a side note, the HP Service rep was very friendly, and definitely tried to support the HP Product, which is much more than I can say about Netgear.
Thank you,
This question was solved.
View Solution.

Hi,
More likely the issue related with Multicast, which Apple devices relies on to communicate with teh device through the network.
First try unplugging the router for 30 seconds.
Plug it back to the power and wait for 2-3 minutes.
Turn the HP printer Off and back On, then check for any difference.
If the same persists, try changing your router configuration as following
Note: the settings below are not related with the HP product, I provide you the steps as a best effor and those are only based on my own knowledge. you may try modifying the router settings at your own risk:
Open the router configuration page (can be found listed as the Default Gateway by clicking the Wireless icon on the printer, then print a network configuration report.
Click the Advanced tab.
Click the Setup option from the menu, then click on WAN Setup.
Make sure to uncheck the box next to Disable IGMP Proxying and Apply the changes.
Click the LAN Setup on the same Setup menu.
Set the RIP Version as RIP-2 and Apply the changes.
Reboot your router and then check for any change.
I hope you may find that information useful, you may also use the user guide below for further information:
http://www.downloads.netgear.com/files/GDC/WNDR4500/WNDR4500_UM_07DEC2011.pdf
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

My Hp 8500a plus printer keeps saying it is offline and will not print. Was printing now stopped.

I have an HP 8500a plus printer. Lately, when I go to print from Macbook or iPad, it tells me the printer is offline. My printer says it is connected to my wifi but will not print. Printer firmware is up to date. I have changed nothing, and now it will not print. Very frustrated and tired of spending all of this time trying to fix the printer just to print. This is my second HP printer this month and it works sometimes and doesn't work sometimes.
Am I missing something? I don't understand how it can print one day and not the next.

Try this if it is an Airprint Printer.
1. Turn the router, iPad and printer off
2. Turn on the router and then wait 30 seconds
3. Turn on printer and then wait 30 seconds
4. Turn on your iPad and test print.

I changed routers- mg3200 will not print. cannot find cd. HELP!

Similar Messages

Maybe you are looking for