I could not send out message and I could not hear anything when someone calls .

Iphone3GS unable to send out MSG and incoming/outgoing calls does not work. Had reset network but problems stiill intermittent

Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Has any of this been tried?
What specifically is happening?  Any errors?

Similar Messages

  • I can't hear anything when making calls no dailing tone or anything but when I try and audioface time it works fine please help

    I can't hear anything when making calls no dailing tone or anything but when I try and audioface time it works fine please help

    Hi Nfrith1,
    Please take a look at the article referenced below, the same as in my original reply.  The receiver on the iPhone does not have anything to do with the speakers on the bottom of the phone nor your microphone.
    Clear the receiver
    The iPhone receiver won't work properly if it's blocked or dirty. Here's where the receiver is:
    Follow these steps, testing after each:
    Make sure nothing is blocking the receiver, such as a case or film.
    If you have a new iPhone, remove the plastic film on the front and back of the device.
    Check the receiver opening to see if it's blocked or dirty. If necessary, clean the receiver opening with a clean, small, dry, soft-bristled brush.
    While you're on a call, turn on speakerphone. If you still can't hear, then your network or reception could be the issue. Try calling again later or from a different location.
    Restart and update
    Restart your iPhone and test again.
    If there's still no sound or poor sound quality, update to the latest version of iOS.
    Get more help
    If you've tried these steps and there's still no sound or poor sound quality from your iPhone, contact Apple Support.
    Learn what to do if other people can't hear you on a call.
    If you can't hear a person on a call or voicemail or if the sound quality is poor on iPhone
    Take care,
    Alex H.

  • I bought an iPhone from mobile and I can't hear people when they call me unless their on speaker do I have warranty for that

    I bought an iPhone from mobile and I can't hear people when they call me unless their on speaker do I have warranty for that

    You can check your warranty status by entering the iPhone serial number here:
    https://selfsolve.apple.com/agreementWarrantyDynamic.do
    Be sure to make an appointment at the Genius Bar before taking your iPhone in
    as per deggie above.

  • Ringer and alert messages won't play on iPhone 4 when someone calls or sends a message, just vibrates.

    Hello, I updated my iPhone 4 and after updating it to 5.0.1, all my sounds won't play, it vibrates when someone calls me, but it will not ring, or notify if there is a new message, however when I go to setting n tap the song to preview it, it will play, what happened to my phone this has never happened before I updated to ups 5.0.1, I already turned it off and back on but still no good, please help.

    Rebooting the phone seems to have solved this for the time being. I will let everyone know if it recurs.

  • My wife and I both have iPhones recently when someone calls her phone mine also rings.  How do I stop this?

    Both my wife and I have IPhones (5C and 4S).  For some reason for the last several months when someone calls one of our phones it rings on both phones.  It seems to have started with the OS updates but that may be a coincidence.  Is there a way to stop this? 

    DrYes wrote:
    So if I turn off IPhone Cellular calls this will eliminate the problem?  As I read it the double ringing only occurs when we are signed in and the phones are close and connected to WIFi.
    Correct, I wouldn't lead you astray with a false response.  It happens because you and your wife are using the same Apple id for facetime - which you shouldn't do, either you or her will need a separate id for facetime.
    This subject has been brought up already, you can use the search function and look for the threads with the green checkmarks.

  • I have an iPhone 4, and the other person can not hear me when i call, any ideas?

    I am originally from SD, but i was in boulder, colorado this weekend and my iPhone 4 worked fine on Saturday. I got up on Sunday and when i would make a call, the person on the other end could not hear me. I thought it might have been something with the service, but once i got back to SD, the same thing happened. I took it into AT&T and they said it was probably something with the microphone, well today i tried facetiming someone and they could hear me. Anyone know any solutions or what may be wrong?
    Thanks!

    Hello,
    My volume buttons dont work neither does the silence one but i have flicked it either way and no difference my alarm works and the sound on video's work but just not calls and texts?!

  • Nokia N95 8gb cannot hear anything when I call out...

    When making calls to other mobiles I cannot hear the ringing or the other person but they can hear me. This is very frustrating and costs me a lot of money because it takes four calls to get it to work correctly.
    I have tried switching to loud speaker and that does not work. I have the latest software.
    There is no noise at all, no ringing, no talking from the other side. The person on the other side can definately hear me though.
    It is weird because it works fine on the third or fourth try.
    Please help, I dont want to send my phone away to be repaired unless necessary.

    hi,
    you might want to try the following 1st...
    re-start your phone, just turn it off and turn it on again
    if that doesnt help then you can try this more drastic measure, but 1st make a backup of your phone's content by going to the memory card and make backup and/or use Nokia PC suite to make a backup, then try the Soft Reset or Hard-Reset: Remember to backup specially for hard-reset, all your phone's content will be erased.
    FOR SOFT-RESET:
    - at Standby Screen type-in => *#7780#
    It will ask for “Restore all phone settings-phone’ll restart….”
    Then it asks for security code enter factory default => 12345
    FOR HARD-RESET:
    - at Standby Screen type-in => *#7370#
    It will ask for “Restore all phone settings-phone’ll restart….”
    Then it asks for security code enter factory default => 12345
    if this doesnt help contact Nokia Care Point-> http://europe.nokia.com/A4388379
    if you are not comfortable with the hard-reset and it is easy for you to go to the nearest Nokia Care Point, then just go there for help...

  • What do i do if callers cannot not hear me when I call them

    After iOS 5 update, callers cannot hear me. I tried the voice recorder and it does not pick up my voice. also I used Tango and the caller could hear me but with Skype they could not. the only way callers can hear me is if I have the phone on speakerphone. I have not tried bluetooth or headphones. I have reset, restored etc.

    Remove all screen protectors and cases and try your phone.
    Basic troubleshooting steps are restart, reset, restore (first from backup, then as new).  If these steps fail, you have a hardware problem.
    Out of warranty exchange is $199 in the US.  Some Geniuses have been known to waive the exchange fee if you're really close to your expiration.  If you go in NOT expecting this, perhaps you might get lucky.

  • Not able to hear anything when I make calls..after upgrading

    After upgrading to software version 3.1.3, I can not hear anything when I make calls.. Only able to speak through speaker option. Can anybody help...?
    Message was edited by: halenbach

    Here's one article that might help.
    http://support.apple.com/kb/TS1630
    Also, try these steps in this order.
    Toggle Airplane mode off then on. Leave off for at least 10 secs
    Toggle 3G Mode off then on. Leave off for at least 10 secs.
    Power phone off and then on.
    Remove and replace SIM card.
    Those will fix that issue the majority of the time. If not, you'll need to restore the phone.

  • All my data on my phone got deleted so I restored it through Itunes and now my IMessage will not recieve nor send out messages through my phone number but my email. I've tried alot but non is really working, help please !!

    All my data on my phone got deleted so I restored it through Itunes and now my IMessage will not recieve nor send out messages through my phone number but my email. I've tried alot but non is really working, help please !!

    Ok. You don't have to select your number. Just check your email under your "grey" number and then at the bottom of this page you will see the option "Start new conversations from". Select your number.

  • My mail can send out message but can't receive new e-mail? and some software(adobe illustrator cs) and applications(terminal) can't run ? but in another user account, terminal and illustrator can run.

    Hi,
    My Mac info:
    Machine Name:          Power Mac G5
    Machine Model:          PowerMac7,3
    CPU Type:          PowerPC G5  (3.0)
    Mail Version 2.1.3 (753.1)
    My mail application can send out message but can't receive new e-mail now ? please see attached before my capture screen
    and some software(adobe illustrator cs) and applications(terminal) can't run ? please see attached
    but in another user account, terminal and illustrator can run.
    Please kindly help to check with these problems. Thanks.

    Verify and Repair disk “Data”
    Checking HFS Plus volume.
    Checking Extents Overflow file.
    Checking Catalog file.
    Checking multi-linked files.
    Checking Catalog hierarchy.
    Checking Extended Attributes file.
    Checking volume bitmap.
    Checking volume information.
    Volume Header needs minor repair
    Repairing volume.
    Rechecking volume.
    Checking HFS Plus volume.
    Checking Extents Overflow file.
    Checking Catalog file.
    Checking multi-linked files.
    Checking Catalog hierarchy.
    Checking Extended Attributes file.
    Checking volume bitmap.
    Checking volume information.
    The volume Data was repaired successfully.
    Mounting Disk
    1 HFS volume checked
    Repair attempted on 1 volume
      1 HFS volume repaired

  • Was skiing with a lifeproof on and my phone did not get wet. On the ride back my phone was struggling to send/receive messages and had trouble opening apps. The screen froze and I hit the sleep button; since then, it has not turned on. A

    Was skiing with a lifeproof on and my phone did not get wet. On the ride back my phone was struggling to send/receive messages and had trouble opening apps. The screen froze and I hit the sleep button; since then, it has not turned on. Any suggestions on what to do?

    It probably got too cold and shut down. Warm it to room temperature, then hold the HOME and SLEEP buttons at the same time until an Apple logo appears.

  • My iMessage will not send out messages on my iPad. How do I resolve?

    My iMessage will not send out messages on my iPad. How do I resolve?

    iMessage can only send messages to other iOS devices using their email address. Make sure the person you are sending has i message set up.

  • Proxy does not send out message automatically

    Hi expert,
    I am using proxy to send out message. After I call my proxy class, I did commit work. But when I check in sxmb_moni, it just sit there. Status said "scheduled". In the queue, it said "ready". I had to manually make it run. How I can make it automatically run?
    Thanks,
    Charles

    Hi,
    Try the following, any one might work.
    1. The user id associated with the proxy need to service user. Please check that.
    2. Check inbound queue whether any message stuck
    3. You can try re-registering the queues
    Regards
    Ramesh

  • Mail suddenly stops sending out messages.

    I use Mail with Snow Leopard. I have 3 email accounts: U-verse, MobileMe and godaddy.com. Up until last week everything worked just fine. Then Mail stopped sending out messages on all three servers. They just sit in the Outbox. I can receive messages OK. I can go online and use the associated webmail sites. Connection Doctor gives me green dots on all accounts. Have not changed any settings although I did confirm they are configured properly. What the heck is going on?

    That means nothing is wrong with Mail itself. The problem lies in your data. Mail is a very complex application with a lot of files. Rather than going through a long diagnostic process, I suggest you make a record of all your account settings, quit Mail, move your Library/Mail folder to the Desktop, delete the file Library/Preferences/com.apple.mail.plist from your home folder, and start over with a clean slate. Set up your accounts as if for the first time, test, and if all seems well you can restore your messages either from Time Machine, if you use it, or by importing them from the old Mail folder (File > Import Mailboxes...). It will take some work, but I don't know of an easier way. Make sure you have backups of everything before you start.
    If you do use Time Machine, you have the option of restoring all the Mail files from a snapshot that predates the issue, but then you'll also have to find and restore the messages created since that time.

Maybe you are looking for

  • PNPCE in ABAP Query !!! Slection is not working completely

    Hi   I have developed an ABAP query using LDB PNPCE. I am reading data from IT000,IT0001 etc . I test the query in QA and I noticed that the PNCPCE screen doesn’t care about the selection in query. Like I have given the date range in PNCPE default sc

  • Step-by-step Java card

    Does anyone can tell me how to program Javacard Step-by-step....and what tools we can use to program it. thanks...

  • Alv Output after dynamic selection screen

    Hi Guys I have coded a dynamic selection screen (shown below). I want to create an ALV report based on what the user enters in the selection screen. Is the right way of doing this to code an IF s_matnr is not initial statement then call all the subro

  • How to uninstall R12 instance

    Hi friends next week i have to decommission UAT2 instance please let me know steps to shut it down UAT2 instance, Thanks

  • New XI serv install - get 'unexpected error' when loading report to package

    Brand new install of Crystal Enterprise XI R2.  I've setup an object package.  When I try to add a crystal report I get 'unexpected error' massage.  Any help would be appreciated.