I'd heard about a bios bug!

Question

Hi guys,
my system running not allways stable!I got some bluescreens of the art "STOP COMMAND"!
Exactly this three ones:
IRQL_NOT_LESS_OR_EQUAL
PAGE_FAULT_IN_NONPAGED_AREA   and
BAD_CALL_POOLER
HERE are some information about it,but sorry,it's in german!
I think that the faults causes maybe in that two ways!
Once is a Memory error,because I become sometimes error Popups,that adresses can't written or read!
I use one TwinMos Modul of PC3200,512 Mb!
At the moment I test it in slot 3 and it seems to be more stable as in slot 1!The time settings seems to be not so important,I can use either 2.5-3-3-6,or 2-3-3-6!Normal is(I'm not sure 2.5-3-3-8)!
But more important I think is,that the motherboard monitor shows me a core voltage of under 1.5V~1.48v!!!That is also the reason I mean,that I can't overclock my system over 205 MHz frontsidebus stable!In 3D Mark 3 I get instantly by the first test Wings of Fury a totaly blue screen(not the error bluescreen!Much darker and without any message!)
So I'd heard about a bug in the AMI bios,that you can't  store a new core voltage!Either increase,nor decrease!My settings are on 1.55 Volt!Isn#t that the right voltage for the prozessor and if,why it isn't there a possibility to increase the core voltage for overclocking!But that is a must for a good result!I'm a little bit confused about that!The other possibility is,that my PSU is not strong enough!What for a Voltage is important for the CPU Core?I mean the 3.3V,or?My customer had said that he test the PSU and it's stable!It shall be have 32A,normaly it is enough to hold the voltage correct,but I knew that in china the electric is another as in germany!!!
Another problem is that I have change my drive from the VIA controller to the promise,because I would first test  the speed and if this controller is able to read the correct monitoring data(Firmware,temperature,UDMA mode...)!The VIA doesn't do that but the promise can!And I use now together my old seagate drive on it.
Because HDTunenow show me the correct UDMA mode,I'd seen that both drives are not running at their best settings!The samsung run at UDMA5,but can run on 7 and the seagate run on UDMA2,but can  do it on 5!So I would change it,but I have no idea where I can do that!In the hardware manager it isn't a possibility,neither on IDE(there is only the VIA),nor at the SCSI devices!I cannot see any settings therefor at the promise controller!And if I change the settings in bios on RAID(for S-ATA) and go into the RAID Menue with Ctrl+f on bootup,I can see keys for changing values,but their shows no result!And I think if their would working I can't use it,because with the RAID setting the computer will not boot if you don't create an array!
Has anyone some ideas???
Thank you very much!

Answer 1

Thanx man!
How I write it in my system specifications,I'd try to change the slot and it seems to be better with the RAM in slot 3!
But,is it my not so good english or why you did not wrote anything about the bios bug I'd heard from!Is it true that it gives a bios version with this bug,that doesn't allow to store another core voltage?Because I think that is the problem!That my core voltage is only at 1.48V,wether I changed it to 1.55V,neither if I do that in bios,nor in bios on auto and do it with core center!
What is the "normal" processor voltage?1.5 V?And if,why it gives no possibility to increase it higher than 1.55V for overclocking?What for voltage amounts are important for the processor to run stable?Only +3.3V or also the  +5V and +12V amounts?
But anyway, it seems to be that the +3400  version of the processor is coming at its end of power and isn't so good to be overclocked!Better I'd bought a +3200 one I think!
But my system is also good without overclocking if I take a look at my 3DMark and Aquamark results!!:worship:
And my system isn't so old,only 2 month,but the errors comes also in the fresh system at the first days!
Greetings from good old Germany!