I didn't find configure terminal command in the ios of aironet 1131AG

Question

Dear All
i bought cisco aironet 1131AG yesterday. when the AP get IP from DHCP and trying to access it by internet browser, the web page is empty so i tried to access AP by console and login in to the privileged mode but i did't find the configure terminal command to enter the config mode.
what is the problem !!!???
is the IOS version problem?
the details of show version command :
Cisco IOS Software, C1130 Software (C1130-RCVK9W8-M), Version 12.3(11)JX1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Mon 17-Jul-06 11:38 by alnguyen
ROM: Bootstrap program is C1130 boot loader
BOOTLDR: C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
AP001e.7abd.dca6 uptime is 3 hours, 9 minutes
System returned to ROM by power-on
System image file is "flash:/c1130-rcvk9w8-mx/c1130-rcvk9w8-mx"
cisco AIR-LAP1131AG-A-K9   (PowerPCElvis) processor (revision A0) with 24566K/8192K bytes of memory.
Processor board ID FOC12072A3U
PowerPCElvis CPU at 262Mhz, revision number 0x0950
Last reset from power-on
LWAPP image version 3.0.51.0
1 FastEthernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:1E:7A:BD:DC:A6
Part Number                          : 73-8962-12
PCA Assembly Number                  : 800-24818-11
PCA Revision Number                  : B0
PCB Serial Number                    : FOC12072A3U
Top Assembly Part Number             : 800-29144-02
Top Assembly Serial Number           : FOC12072A3U
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1131AG-A-K9
Configuration register is 0xF

Answer 1

Hi,
The APs image is LWAPP and to access the config t command we need to convert the IOS to Autonomous.. here is the step by step procedure that we need to follow to get the issue resolved..
C1130 Software (C1130-RCVK9W8-M)
I request you to do download any image from the below link and perform the conversion from LWAPP image to autonomous..
http://www.cisco.com/cisco/software/release.html?mdfid=279537722&flowid=6775&softwareid=280805680&release=12.4.25d-JA&rellifecycle=ED&relind=AVAILABLE&reltype=latest
the method to convert is..
download TFTPd32 from google and install it on ur PC.. point the image that you have downloaded in the TFTP server..
connect  a ethernet cable between ur laptop and AP.. both should be in the same  subnet.. and connect a console cable and get the hyperterminal console  access and issue the command..
AP>en
AP#debug lwapp console cli or debug capwap console cli
AP#config t
AP(confg)int fa 0
AP(confg-if)ip addr (same subnet as that of the laptop)
AP(confg-if)end
AP#archieve download-sw /force-reload /overwrite tftp:///
eg-
Assuming tftp ip address is 10.0.0.1 and the image is c1130-k9w7-tar.124-25d.JA.tar, then..
AP#archieve download-sw /force-reload /overwrite tftp://10.0.0.1/c1130-k9w7-tar.124-25d.JA.tar
The AP will reload and it will come up with IOS image and you will be able to enter the config mode
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull