I get a gray screen with the apple logo at start up and the trackpad doesn't work
My MacBook Pro has run fine until yesterday. It froze and wouldn't receive commands from the trackpad. I was still able to move the cursor but clicking or tapping the screen did nothing. I tried restarting but got the gray screen with the Apple logo and the spinning wheel. To get pass this I have tried resetting the NVRAM/PRAM and performing the safe boot. I also tried using the Disk Utility at start up but since I can't use the trackpad it was unsuccesful. I got pass the gray screen once performing the safe boot and restarted and everything run fine (including the trackpad) for about 20 minutes before freezing again. Now I'm back at the gray screen again and can't seem to get pass it again.
Any advice what should I do next?
I would back up the files and start looking at the HDD. Open DISK UTILITY>FIRSTAID.
Ciao.
Similar Messages
-
I download a suggested "update" from the App Store for my iPhoto yesterday. Now when I try and open my iPhoto, I get a grey screen with the rotating circle icon in the middle......that just keeps rotating. Ergo, it won't open!!! Before the "download" all was fine in Heaven & Earth....now, I'm a little peeved.
Anyone have a suggestion?
Thanks,
Wayne K.
ps Have a good day, God Bless America ...............and be weary of iPhoto update downloads,very weary.No need to be wary of iPhoto updates however it is a good idea to follow the instructions when updating. I haven't updated iPhoto from the App Store before however it should not be much different than doing a DVD update. Here are instructions on updating the library:
http://support.apple.com/kb/HT4431 -
my 27 inch 2011 iMac is not boting up, the cumputer is stuck on a grey screen with no apple logo or spinnign wheel. The iMac is not giving power to the keyboard as it is not ligthing up the caps lock botton when pressed.
Contact Apple Service, iMac Service or Apple's Express Lane. Do note that if you have AppleCare's protection plan and you're within 50 miles (80 KM) of an Apple repair station, you're eligible for onsite repair since yours is a desktop machine.
-
Mac Stuck at Startup Screen with Grey Apple Logo,Empty Progress Bar and a Spinning wheel
Last night the electricity went out and my power surge protector was not working so my iMac just force shut downed.
So, when the electricity came back i turned on my Mac but it is *Stuck in the Startup/Boot Screen with a Grey Apple Logo,a Empty Progress Bar with stays for 1 or 2 minutes and a small Spinning Wheel which would Spin Forver! I Have tried the SMC and Pram reset but no use, i have also tried to insert my OS X Lion 10.7 Installation disk and it would not load if i hold the C Key in the Startup, I Have Managed to go to Disk Utility Through "Recovery HD" but the Volume "Macintosh HD" is Greyed out and Unmounted and i cannot repair it. There are some files that i'd like to Recover if there is a way to fix it without deleting files.
**PLEASE HELP ME FIX THIS!**
Details about the iMac:
iMac 21.5 Inch i think from Mid 2010,
OS X Lion installed maybe 10.7.2 or 10.7.3 (im not sure)kernel
Grey screen with Metallic Apple and spinning gear
Sounds to me like your hard drive failed on you as a result of the power going out.
http://www.apple.com/support/imac-harddrive/
If your iMac is a Mid 2010 you qualify for the hard drive replacement program from Apple.
Apple has determined that certain Seagate 1TB hard drives used in 21.5-inch and 27-inch iMac systems may fail. These systems were sold between October 2009 and July 2011.
I hope I helped you with your problem.
- Brandon -
Non-booting Mac mini (stuck at gray screen with no Apple logo or others)
We've got a G4 Mac mini whose motherboard was recently replaced. I've put it back together carefully following the instructions on pbfixit.com, but I can't get it to boot.
When powered on, the chime sounds normal, and the screen comes on after a few seconds with a gray background--no Apple log, no spinner, no error, no flashing icons, nothing.
I've already zapped the PRAM 3 times using OptCmd+PR, no go.
I'm able to get into OpenFirmware using OptCmd+OF and have done reset-nvram and reset-all, restarting the machine, but no luck. The system date remains current also, indicating perhaps it's not resetting the PRAM either way somehow.
The disc drive won't accept a boot CD or DVD as if it's unpowered, but it's snugly connected.
I'm unsure what to test next. Suggestions? Thanks.Greetings,
I just had the exact same problem with a Mini. Would only boot to a gray screen no matter what I did. Booting into the OpenFirmware did help, booting into the Startup utility (by holding "T" down at startup showed no hard drive and no CD/DVD drive.
Hold on to your hat . . . .
The issue was the battery. These guys have a Lithium battery that allows them to boot up, a battery that can be purchased anywhere that sells those kinds of thing. I bought 2 for $3.50, it was more time and trouble to get into the case and get at the logic board but once the battery was replaced everything works like a dream.
Here is an excellent step-by-step tutorial about getting into the case http://www.sterpin.net/uk/ddMacMiniuk.htm. Just make sure that doing so doesn't void any warranties.
Good Luck!
Gail -
My macbook air turns on but not completely, it gets stuck on the grays screen. It shows an apple an a spinning wheel and that is as far as it gets. sometimes I can get to an screen that shows macintosh hd and i clicked on it and the computer turned off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My Imac is not starting , I get a gray screen with the logo and a bar below and about one minute the bar desapier and shot off by itself. I try evething that I can think of and not luck. I did disconect all accesories and still the same, I use the start up disc and same.. now I can not get the disc out.
Please advise what I need to do to solve the problem. Recently this computer was upgraded from 10.4 to Mountain lion and add more memory.Thanks for your help.
Same thing happen when I hold the button, it idle for a while and then turn off by itself. Any more suggestions?
I got the disc.. -
I have an early 2008 MacBook and running iOS Lion. I just turned on FileVault and restarted my computer as instructed. It told me before hand that I would still be able to use my Mac while the files were being encrypted. However, when I logged in on the secure gray login screen, I was only directed to a plain gray screen with the apple logo in the center. There are no time turners or anything moving. Is my Mac encrypting or is it frozen in some sort of way? If it is encrypting, how long does it usually take? and if it is frozen, how do I unfreeze it?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
on start up i just get a grey screen with the apple logo-this has suddenly started happenin. Please help?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
My MacBook Air will not turn on. I get a white screen with the apple logo and a spinning star (search icon). It will spin for hours and never go away unless I power off.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
MBP has gray screen with question mark folder on start up
Hi Mac Experts,
I have a MBP that won't start up. I get a gray screen with the question mark folder. Nothing else. I tried starting without the battery and also while holding the shift key but still get the same result. Any idea what happened and what I should try next? Thanks!Need a Vacation:
Use the Leopard disk.
Repair Disk
Insert Installer disk and Restart, holding down the "C" key until grey Apple appears.
Go to Installer menu (Panther and earlier) or Utilities menu (Tiger and later) and launch Disk Utility.
Select your HDD (manufacturer ID) in the left panel.
Select First Aid in the Main panel.
(Check S.M.A.R.T Status of HDD at the bottom of right panel, and report if it says anything but Verified)
Click Repair Disk on the bottom right.
If DU reports disk does not need repairs quit DU and restart.
If DU reports errors Repair again and again until DU reports disk is repaired.
If DU reports errors it cannot repair you will need to use a utility like Tech Tool Pro or Disk Warrior -
Start up with a white screen with an apple logo keep on spinning
my imac 10.5.4 version won't start up it has white screen with apple logo and keep on spinning it's been 2 weeks now try to fixed it i tried everything no luck im trying the verbose what i see on the screen is that diskOs2:0xe0030005 (UNDEFINED) please help me !!!!
Hi Haziq0135,
Welcome to Apple Support Communities.
It sounds like your MacBook Pro is starting up to a gray screen with a Apple logo and a spinning gear. The article linked below provides a lot of great troubleshooting suggestions that should resolve issues like that.
Mac OS X: Gray screen appears during startup
http://support.apple.com/kb/TS2570
I hope this helps.
-Jason -
Help, Turned on MacBook Pro this morning and just get a white screen with grey apple logo and spinning gear. Cannot access desktop.
Computer starts up in Safe boot by holding down the shift button. But when I go to restart the same thing happens. What should I do?
-
My mac doesnt start. All i get is the gray screen with the apple and the loading icon but nothing more happens. I tried to start it in safe mode but it doesnt help. What can i do?
If you have a external USB enclosure - trying installing your hard drive in that enclosure and connect it to your usb port - restart your macbook while holding down the options key. If you Macbook boots to your desktop then you have a faulty cable. If you get the same error, then your hard drive just died on you.
good luck. -
My computer will not start up. It powers up, I get the gray screen with the apple, then the loading progress bar starts loading to about 25% the the screen goes black. what can I try to get my computer up and running?
Carolyn Samit wrote:
iMac, Mac OS X (10.7.1)
Use Command + R for Lion Recovery
Try restarting, when you hear the startup tone hold down the Option key. Then choose the Recovery Partition.
Maybe you are looking for
-
How do I know if my iPad 2 is already upgraded to iOS 5?
I have just purchased new Apple iPad 2 16 GB Wi-Fi Apple A5 1 GHz Dual-Core 9.7-i and do not understand if it is an iOS 5, 5.1 or....etc. Am a bit old to be starting this sort of thing but really would like to understand what I am doing!
-
Downloaded pdf files won't open in firefox
I have this irritating problem. I need to open pdf files that are already downloaded and stored in my hard drive, so it would be easier to translate them and ect. Either i am doing it wrong, but when i try to do that, i always get a regular Save/Open
-
Can someone help me with Premiere Elements 2?
I have been working on a slide show for my son's class graduation. This is the second time I've used PE2 to create a slide show, so I am not very good at it! I completed my slideshow (which contains about 100-150 photos, 1 video and audio) I burnt a
-
hi i need some help because i compared my friends iphone to my touch. and his iphone is like dark dark black on the screen and my touch is lighter. i wanted to know if this is how the touch is? anybody having this problem.
-
My new iMac w/ OS 10.5 will not open my PE3. It shuts down before it is fully open! Can anyone shed a little light on this problem?