I had a itunes logo with usb cable ? can anybody help me

i was updating my ipad into 7.0.3 but my ipad has a problem with wifi, because if this problem the network was disconnected then i press home and sleep button
then it bring a itunes logo with usb cable
is i need to format my ipad ? it contains a important things

If the  Apple Mobile Device driver is not the problem or you need more help see:
iPhone, iPad, or iPod touch: Device not recognized in iTunes for Windows
or
iPhone, iPad, iPod touch: Device not recognized in iTunes for Mac OS X
If you come back with the wording of the error mesage we can probably provide more specific recommendations.

Similar Messages

  • I plugged my Ipad3 in order to update the software to version 6.1 but I got an error and my Ipad now is locked, it's showing the Itunes logo with usb cable on the screen. What should I do now?

    I plugged my Ipad3 in order to update the software to version 6.1 but I got an error message and my Ipad is locked now, it's showing the Itunes logo with USB cable on the screen. What should I do now?

    You will probably need to restore using Recovery Mode. You can read about it here.
    http://support.apple.com/kb/ht4097
    Or you can follow these Recovery Mode Instructions
    Disconnect the USB cable from the iPad, but leave the other end of the cable connected to your computer's USB port.
    Turn off iPad: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for iPad to turn off.
    If you cannot turn off iPad using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the iPad turns off, release the Sleep/Wake and Home buttons.
    While pressing and holding the Home button, reconnect the USB cable to iPad. When you reconnect the USB cable, iPad should power on.
    Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears you can release the Home button.
    If necessary, open iTunes. You should see the recovery mode alert that iTunes has detected an iPad in recovery mode.
    Use iTunes to restore iPad.

  • TS1369 iphone showing blue itunes logo with usb cable

    after copying recent purchases from iphone 4s and
    updating itunes software
    iphone not showing in devices in itunes but
    it does showing in Windows 7.
    Iphone shows blue itunes logo with usb cable.

    Hi there gdavis433,
    You may find the troubleshooting steps in the article below helpful.
    If you can't update or restore your iOS device
    http://support.apple.com/kb/ht1808
    -Griff W. 

  • Tried updating software but now frozen with itunes logo and usb cable picture on screen help

    Tried updating ipod software, now frozen with itunes logo and usb cable picture on the screen. Computer will not reconise it

    - If ou can turn the iPod off, then see if manually placing the iPod in Recovery mode  will allow a restore. Next try DFU mode.
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If it always remains on let the battery fully drain. After charging for at least an hour try a rest and restore.

  • HT201412 it shows itunes logo and usb cable with arrow after that it switch off itself

    iPAD shows itunes logo and usb cable with arrow after that it switch off itself

    If the Restore doesn't work, force your iPad into Recovery Mode:
    1. Turn off iPad
    2. Connect USB cable to computer; leave the other end alone
    3. Press and hold the Home button down and connect the docking end of cable to iPad
    4. Continue holding the Home button until you see the "Connect To iTune" screen
    5. Release the Home button
    6. Open iTune
    7. You should see "iTunes has detected an iPad in recovery mode"
    8. Use iTune to restore iPad
    Note: You need to be patient and repeat the above many times to recover your iPad

  • After I upgraded my iPad 2 to 6.1.3 I now have a itunes logo and USB cable showing.  What has happened?

    After I upgraded my iPad 2 to 6.1.3 I now have a itunes logo and USB cable showing.  What has happened?  What do I do to get by this.  I can not shut the iPad down at all.

    Using iPhone/iPad Recovery Mode
    http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
    Saw this solution on another post about an iPad in a school enviroment. Might work on your iPad so you won't lose everything.
    ~~~~~~~~~~~~~
    ‘iPad is disabled’ fix without resetting using iTunes
    Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
    I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
    Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
    1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
    2. Open iTunes with the iPad disconnected.
    3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
    4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
    5. Click ‘Setup as new iPad’ and then click restore.
    6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
    7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
    8. The first stage in the restore process unlocks the iPad, you are basically just cancelling out the restore process as soon as it reactivates the iPad.
    If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
    ~~~~~~~~~~~~~
    Try it and good luck. You have nothing more to lose if it doesn't work for you.
     Cheers, Tom

  • My iphone froze up when i tryed up dating my 3gs and the only thing comes up on my screen is the itune logo and usb cable how do i fix the problm

    i was trying  to update my iphone 3gs to ios 6 and then on my iphone screen comes up with a itune logo and usb cable i tryed turning it of conecting it back to the computer and notting happens what do i do how do i fix this problem

    mine has done the same thing. itunes isnt even recognizing that my phone is plugged in.

  • Software update failure, now phone frozen. Now screen only showing itunes logo and USB Cable on screen. Have I lost my backup?

    I just tried updating the most recent software on my 3GS (on my Mac) but it said the updated on my phone failed. Now my phone is frozen and only showing the itunes logo and USB cable. When I connect to the USB lead, its says: iTunes has detected an iPhone in recovery mode. You must restore this iPhone before it can be used with iTunes.
    Have I lost all the data on my phone?
    What should I do?
    Help!
    M

    The iTunes logo and cable indicates that your iPad has gone into recovery mode : http://support.apple.com/kb/ht1808
    For the 3004 error code does the troubleshooting for it on the page that you posted from not help ?

  • HT201210 I was in the middle of installing the new update using the wifi at a local restaurant when I lost the wifi signal and my iPhone shut down, and now I can't get into the phone. I only get the iTunes logo with the cable pic. What are my options now?

    I was in the middle of installing the new update using the wifi at a local restaurant when I lost the wifi signal and my iPhone shut down, and now I can't get into the phone. I only get the iTunes logo with the cable pic. What are my options now?

    Your only option is to connect your iPhone to your computer via USB (as the diagram indicates) and restore using iTunes.

  • IPhone shows a picture of the Itunes logo with a cable underneath, iPhone shows a picture of the Itunes logo with a cable underneath

    G3S Phone was disconnected during upgrade the os 5. After a restart it Now shows a picture of the Itunes logo with a cable underneath.
    How do I fix this problem?

    If you have a pass code lock on your phone try unlocking it prior to connecting it to your computer.

  • Tried synching iphone for the first time on new PC and got error followed by itunes logo and USB cable picture. No idea what went wrong and now phone is in this screen locked. please help!

    tried synching iphone for the first time on new PC and got error followed by itunes logo and USB cable picture. No idea what went wrong and now phone is in this screen locked. please help!

    I tried connecting to iTunes and neither the PC nor iTunes recognizes the device. I went through all the troubleshooting on the Apple website for this issue and nothing worked. I've reinstalled iTunes, the driver, everything and still can't get either the PC or iTunes to recognize the phone.  I don't know what else to do :-( any help or suggestions are highly appreciated!
    I would hate to have lost all my info, especially contacts and calendar items since I have no idea what was backed up prior to the phone getting locked on this screen. I've been told that my only option is to go to the phone carrier and they will reset it for me, but that means it will wipe out all the info.
    I hope someone has a fix other than that one.

  • Iphone while getting On showing itunes logo with usb connection

    Dear Sir,
    I was upaditng my iphone 4s for from IOS 5.1.1  to IOS 6.1.2 by connecting with a personnel hotspot wifi connection. While doing this my iphone got switch OFF and then automatically got ON and the showing " Itunes logo with usb connection with up arrow".
    Also i tried to switch OFF and ON 2  to 3 times but still showing same.
    Can you please assist me , what i have to do now, to get my Iphone ON as normal like before.
    Awaiting for your quick response,
    Thanks and Regards,
    Vishal Haswani.
    <Personal Information Edited By Host>

    Connect to iTunes on the computer you usually Sync with and “ Restore “...
    http://support.apple.com/kb/HT1414
    If necessary Place the Device into Recovery mode...
    http://support.apple.com/kb/HT1808
    Note on Recovery Mode:
    You may need to try this More than Once...
    Be sure to Follow ALL the Steps..

  • HT1414 hi yesturday i tried to put photos of my phone,and its frozed on me,on the screen its got itune logo,with a cable on the screen,ive tried to switch it of but it goes on again,i cannot use the phone,please help lol

    Hi yesturday,i was tranfering my photos of my phone to my computor,and the phone has froze on me,i cannot switch the phone on or of,what i can see on the screen,is the itunes logo with a cable on the screen,its looks the one you put the cable into one of the ports,there is no way possible to switch of or on please help,im stressed out lol,thankyou francis01224

    Aug 15, 2012 8:28 AM (in response to EricaP1234)
    Try:
    - iOS: Not responding or does not turn on
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • HT4623 upgraded to ios7 iphone now displays itunes logo and usb cable will not restore in itunes, wil not restart

    upgraded to ios7 iphone now displays itunes logo and usb cable will not restore, will not restart

    Hi there emynona,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    -Griff W.

  • Iphone 5 screen is stuck on itunes logo and USB cable?

    iPhone 5 screen is stuck on iTunes logo and USB cable. Reset does not work.

    Place your device in recovery mode as explained here:
    iOS: Unable to update or restore

Maybe you are looking for

  • Jdevloper11g Release 1: Error while running Bean in java

    Hello , I am getting error while running my HRFacadeClient.java [EclipseLink/JPA Client] Adding Java options: -javaagent:C:\Oracle\Middleware\jdeveloper\..\modules\org.eclipse.persistence_1.1.0.0_2-1.jar "C:\Program Files\Java\jdk1.6.0_29\bin\javaw.e

  • Ise 1.1 ActivatedGuest not able to authenticate using radius pap

    Hi, I want to create guest accounts using the sponsor portal and use radius to authenticate with these accounts; Afaik this  is supported as from 1.1mr1 (Show Version output      : 1.1.1.268) When we create an account with the ActivatedGuest Identity

  • Rebuilt IPhoto Library does not display.

    Recently my iPhoto has been crashing, probably because I unknowingly moved a file or files in the iPhoto Library with the Finder. Heeding the advice posted throughout this forum I trashed the existing iPhoto Preferences file, the three thumb files, a

  • Master Details form (LOV based on Detail Column of Join Condition)

    I have created a master detail form where user_id is joining master and details. I have created one dynamic lov based on child user_id in detail block to diplay all user who works under current user. Problem : When i want to select Insert detail acti

  • Customised Document Set view not displaying changes

    Hi I've created a document set and assigned a view to items within the document set. This works fine. I then needed to edit the view, so fired up SPD and adjusted columns, using Add/Remove columns. I can see the changes in when I click and open the d