I had to have a new hard drive installed.  Now programs load slowly and pinwheel spins a lot.  Any suggestions?, I had to have a new hard drive installed.  Now programs load slowly and pinwheel spins a lot.  Any suggestions?

I had to have a new hard drive installed.  Now programs load slowly and pinwheel spins a lot.  Any suggestions?, I had to have a new hard drive installed.  Now programs load slowly and pinwheel spins a lot.  Any suggestions?

It's likely that the new drive isn't working, or it wasn't installed correctly, or you had some other hardware fault rather than a bad drive.

Similar Messages

  • MY hard drive crashed and I had to replace it. Now when I try to sync my iPod with iTunes it says that I have to replace the old library (that is lost forever) with the new library to sync. I do not want to lose all the songs on my iPod! What can I do?

    MY hard drive crashed and I had to replace it. Now when I try to sync my iPod with iTunes it says that I have to replace the old library (that is lost forever) with the new library to sync. I do not want to lose all the songs on my iPod! What can I do?

    Copy all the content on your iPod back to your PC and into iTunes. Then go ahead and sync the iPod with your new library.
    See this older post from another forum member Zevoneer covering the different methods and software available to assist you with the task of copying content from your iPod back to your PC and into iTunes.
    https://discussions.apple.com/thread/2452022?start=0&tstart=0
    B-rock

  • My mac book pro crashed and the logic board died. They said that i could get the hard drive out and it should have all my files on it. How do i get them off and put them on my new computer?

    My mac book pro crashed and the logic board died. They said that i could get the hard drive out and it should have all my files on it. How do i get them off and put them on my new computer?

    Mj
    Do you mean a case for the external hard drive? See here. Hope this may be helpful to you.
    Regards,
    Joseph

  • I had Adobe Acrobat Serial loaded before The hard drive crashed on my old PC.  I have tried to download Acrobat 9 on my new PC, but always get the message "This is not a valid serial number".  I had Adobe 9 Standard on the old.  But what downloads from th

    I had Adobe Acrobat Serial loaded before the hard drive crashed on my old PC.  I have tried to download Acrobat 9 on my new PC, but always get the message “This is not a valid serial number”.
    I had Adobe 9 Standard on the old.  But what downloads from the page http://helpx.adobe.com/acrobat/kb/acrobat-8-9-product-downloads.html is Adobe 9 Pro.  Perhaps this Pro version is the problem. 
    Anyway, can you point me to a way to install Adobe on my new PC?

    You can try Download Adobe CS5 Free Trials – All Direct Links without Akamai | ProDesignTools.

  • I have a new Linksys router.  When I load the accompanying CD it informs me that it supports OS 10.5.8 or later, OS 10.6.1 or later, and OS 10.7 or later.  I am running 10.9.2, which apparently isn't supported by this Router.  Any suggestions?

    I have a new Linksys router.  When I load the accompanying CD it informs me that it supports OS 10.5.8 or later, OS 10.6.1 or later, and OS 10.7 or later.  I am running 10.9.2, which apparently isn't supported by this Router.  Any suggestions?

    No they should be agnostic about what is behind them, but as to support for IP6, or whether any computers or tablets can use AC... and hasn't Apple's own units sometimes stop being supported with new Mac and new versions of OS X? seems so.
    I said above, why would anyone install any kind of software to use a router? although Netgear's GEnie is or was installed on my systems that adds a nice way to log in and manage the router, so I have to take that back a notch.
    Support for modems and ISPs is a concern, my modem is not certified fully with DOCSIS 3.0 or  FIOS.
    Look around and you can find routers having trouble with some network services like Airplay, printing and scanning, the software bundled with router.
    However, ethernet chips, and the driver, can be a factor. Problems with Intel networking chip and high bandwidth streaming and not being able to handle the load when used by wifi euipment like notebooks and other devices.
    I have only seen the LARGE number of complaints on MacBook forums about wifi issues to suspect something is wrong but not sure what. And those are people that depend on wifi I assume, though some could use their Thunderbolt equipped Mac to use ethernet to get around the problems. And I am seeing the same thing with some Windows users and maybe they all have common Intel chips???
    MacBook Pro constantly losing wireless connectivity
    I use Windows 8.1 primarily. I also don't know enough or as much to know "Why is the sky blue" either.
    Just pass along this example:
    If you're setting up a new PC for the first time, check if your router is fully compatible with Windows. Because of the new networking features in Windows (8.1), some older network routers aren't fully compatible and can cause problems. For a list of routers that are compatible with Windows 8.1 and Windows RT 8.1, go to the Windows Compatibility Center.
    Anyone remember when 10.4.0 had so many issues with LAN that it could not be used, work on fix was going on and wasn't complete until 10.4.2/4.3 (and first time we got a new full 10.4.3 DVD because customers needed a reliable system.

  • I have had a new hard drive installed. On start up I transferred all my settings and documents from my time capsule. Once complete I have two user accounts. Mine and guest. I cannot access either. Mine says password incorrect even though its not.

    I have had a new hard drive installed. On start up I transferred all my settings and documents from my time capsule. Once complete I have two user accounts. Mine and guest. I cannot access either. Mine says password incorrect even though its not. Any idea what is wrong here and how I can reset my password. I don't have a start up disc. Thanks very much

    From System Preferences/Help:
    Reset your login password using your Apple ID
    Before you can use your Apple ID to reset your login password, make sure that FileVault isn’t enabled on your computer.
    Also make sure that an Apple ID is associated with your user account, and that an administrator has given you permission to reset your own password using an Apple ID. For more information, see this help topic:
    Associate Apple IDs with your user account
    Make sure your computer is connected to the Internet.
    In the login window, click the question mark in the password field, and then click the arrow in the dialog that appears.
    Enter an Apple ID and password, and then click Reset Password.
    I don't know if it works.

  • Hi, I have just purchased a new Macbook Pro. Whenever I try and buy anything on the internet (via Safari) on any website it will not allow me to add products to checkout. Has anyone else experienced this problem or can suggest a fix? Many thanks!

    Hi, I have just purchased a new Macbook Pro. Whenever I try and buy anything on the internet (via Safari) on any website it will not allow me to add products to checkout. Has anyone else experienced this problem or can suggest a fix? Many thanks!

    On all shopping sites, or only some? What happens when you try?

  • I didn't back up my old computer. I have my oild hard drive in an enclosure and wish to transfer my bookmarks from my old firefox to my new computer's firefox..please help

    I have located the file containing my bookmarks on my old hard drive. How do I move the places. file to my new browser..thank you

    In your file manager (by default that will be Windows Explorer), right-click on the places.sqlite file in the old hard drive and choose Copy.
    Go to the [[profiles|profile folder]] on the new drive, right-click and choose Paste. You should get a dialog box saying the file already exists, choose the option to replace the file. Firefox must not be running when you do this.

  • I used an external hard drive for my backups via Time Capsule.  I bought a new computer and I want to transfer all my old fonts over to the new one but when I go into the Font Library from the hard drive backup but my downloaded fonts aren't there?

    I used an external hard drive to back up my computer using Time Capsule before I bought a new one.  I am slowly transferring information fromt he backup to my new computer and I want to transfer over my old font book.  When I go into the Font folder on the hard drive the only fonts that show up are the ones that came stock with the computer not any of the ones I have downloaded over time.  Could they be downloaded somewhere else?

    The answer to that would probably be "Yes." If you don't remember where your fonts were stored, you may want to search your backups for any of the font files you know the names to. See where that takes you.
    Ideally, Font Book and other font managers will temporarily store the fonts you "installed" into the System when you run the OS. When you shut down, etc. they are removed and reloaded on restart. The permanent place fonts reside is where you saved them when or after you downloaded them. I typically create a Resources folder on the root level of the computer and place a Fonts folder there. Then I install fonts from there, and they are available to all users on that iMac.
    Perhaps if you did not have that kind of a strategy, perhaps many of them are still in your Downloads folder?

  • I have a MacBook Pro and an 1TB WD my passport for mac. I bought a second hard drive to act as back up and when I went to do this the original passport won't mount. It is showing in disc utility but it will not repair. I am told the mac cannot repair it.

    I have a MacBook Pro and an 1TB WD my passport for mac. I bought a second hard drive to act as back up and when I went to do this the original passport won't mount. It is showing in disc utility but it will not repair. I am told the mac cannot repair it and I need to back up the files and then restore the hard drive. But I can't open the hard drive to move the files onto the new one!
    Help me please. I am not very technical so please answer as if I have no clue!! This hard drive has my iPhoto on it and all my pictures of my son, wedding and my current photography course so I  desperate to get it back!
    Any help will he appreciated!

    disk0s2: I/O error.
    disk0s2: I/O error.
    The MBP's disk is damaged and requires replacement.
    Genius Bar Reservations: http://www.apple.com/retail/geniusbar/

  • I had to install a new hard drive because my old hard drives boot files became corrupted, and i want to get all of my music files off the old hard drive and regain all my play counts/ratings/playlists

    Greetings everyone
    as the title says, ive had to install a new hard drive  and i want to transfer my old itunes library onto the new drive, maintaining all playlists/play counts/ratings etc, album artwork if possible. The old hard drive is installed as a slave drive and is completely acessible, but due to the boot files being corrupted i cannot use it as the main drive and therefore operate my old itunes. Also, my ipod no longer contains my music library as itunes synced without my permission and wiped it.
    The only thing i have tried is copying all of my old music files from the old drive by selecting 'add folder to library' and then the old drive, then replacing the new itunes library.itl file with the one from my old itunes. This restores all my playlists and playcounts but when i try to play any of the songs it says that the files could not be found, and i dont fancy locating  8500 music files individually!
    Thankyou for taking the time to read my post, any help will be greatly appreciated.

    Ah, my reply was based on the assumption that you had a default installation of iTunes.
    i.e you had all your music in the iTunes media folder inside your iTunes folder.
    If your iTunes folder is so small compared to the amount of music you have, you must have a different arrangement.
    This complicates you situation considerably.
    iTunes can cope with moving around as long as all the music is in the iTunes media folder, not not if it isn't.
    Your first step should be to get iTunes working on the old drive. This will involve editing the xml library file so that the drive letter is correct and then rebuilding the library from the xml file.
    Then you will need to consolidate your library which moves everything into the iTunes media fodler. After that you will be able to use my first suggestion.
    Step 1
    Find the iTunes folder on the old drive and copy the two library files somewhere else so you can find them again. That's iTunes Library.itl and iTunes Library.xml.
    Now open the copy of iTunes Library.xml with WordPad.
    Look for lines starting:
    Location
    These contain the paths to tracks.
    You will need to use a find/replace to change the drive letter so that it is correct.
    Make sure that you include enough in the "find" so that you only change the right thing.
    Maybe /c:/ and replace with /d:/ or whatever.
    After that, tell iTunes to use the library on the old drive with a shift key start.
    Hold down the shift key and start iTunes, keep holding the shift key until you are prompted to choose a library. Navigate to the iTunes folder on the old drive and choose iTunes Library.itl.
    Then use the method in the following article to rebuild your library;
    http://support.apple.com/kb/HT1451
    Unfortunately the date added will be today for all tracks.
    If iTunes works correctly after this, consolidate your library
    File>>Library>>Organize>>consolidate
    This copies all tracks into to iTunes media folder and could create a problem if you do not have disk space so don't do it if you are unsure about free disk space.
    Check that iTunes works OK and then use the first method.
    Message was edited by: polydorus

  • I have an iPod Touch but I currently don't have a PC.  I found an app that would allow me to connect to my network drive and I was able to transfer music files to it.  These files do not show under the Music app and I can't find any way to do it.

    I need help from some Apple people. I have an iPod Touch and I wanted to load it up with some fresh music but I currently don't have a PC. I found an app that would allow me to connect to my 2TB network drive directly and I was able to transfer a bunch of music files to the iPod. Unfortunately, these new files do not show under the Music app and I can't seem to find any way to convince the iPod that they are music. I can play them through the file manager only. Android doesn't have this problem, any music I put on my phone is recognized as music and can be played through any of the music apps. Am I missing something or is Apple to inflexible to handle this?

    You can't. The only way to get songs in the Music app is to sync from a computer or to download from iTunes.

  • I cannot get my iTunes library from my old computer to my new one. The old computer is so messed up that I cannot even get google to open. I tried to copy to an external hard drive and the music was there until I went to upload to the new computer.

    I cannot get my iTunes library/music from my old computer to my new one. The old computer is so messed up that I cannot even open a browser.I tried to copy to an external hard drive and the music was there until I went to upload to the new computer. I disconnected my old computer so I will have to reconnect it I am sure. thank you for any help. Last time I transferred I used a product I purchased. That was a long time ago.

    First of all make sure that you've definitely backed up the movies to your external hard disc.
    In iMovie click on any event you don't want, go to the file menu and select 'move event to trash'. Then do the same for any unwanted projects - 'move project to trash'. Quit out of iMovie and empty the trash.
    Hope that helps!

  • If I was to get a new computer and transfer all my music from my itunes on my old computer to hard drive then to my new computer and itunes, could I make a new itunes account on my new computer and still be able to use my old songs?

    If I was to get a new computer and transfer all my music from my itunes on my old computer to hard drive then to my new computer and itunes, could I make a new itunes account on my new computer and still be able to use my old songs?
    I am getting a new computer and I know I can transfer my music on my old computer to my new one with a hard drive but me and brother currently share an account and I would like my own, once I get a new computer can I make a new account on my new itunes and still be able to keep my old music and be able to sync it and play it etc?? Anyone with information on this would be muchly appreciated!!! Thank you in advance! Oh and I currently have a windows but will be getting a mac book pro most likely

    The music sync is one one way - computer to ipod.  The exception is itunes purchases.  File>Transfer Purchases
    Have you failed to maintain a backup copy of your computer?

  • I am looking for a spreadsheet app that I can create new spreadsheets. So far nothing looks promising, any suggestions or do I have to go to windows?

    I am looking for a spreadsheet app that I can create new spreadsheets. So far nothing looks promising, any suggestions or do I have to go to windows?

    Hi Tx Tar Heel,
    I've been using Office2HD: https://itunes.apple.com/us/app/office2-hd/id364361728?mt=8
    Its cheaper than Numbers and it also works for Word and PowerPoint files too. I like the Dropbox integration. I can start on my Office docs (Word, Excel, PowerPoint) in the office and then edit those files with Office2HD when I'm out of the office. Files saves right back to Dropbox so that when I get back to the office the files are already updated. Not bad for a $7.99 app!
    Hope this helps!
    ~Joe

  • Windows not recognizing my time capsle - I just purchased a new computer that runs windows 8 and it doesn't want to recognize the time capsule as an external hard drive (ie doesn't show up under my compter).  I've downloaded airport utility...

    I just purchased a new computer that runs windows 8 and it doesn't want to recognize the time capsule as an external hard drive (ie doesn't show up under my compter).  I've downloaded and run airport utility, but it seems to have a hard time finding the time capsule...maybe one out of 10 times it will find it.
    What's more, when I look under network infrastructure under the control panel, it shows my Broadcom ADSL centurylink Router...so I'm wondering if my modem/router combo is overriding the router function on my timecapsule and the time capsule is not being used as a router...
    Any help much appreciated!

    In this case the TC should be in bridge mode.
    Win8 is still problematic. Try using ethernet instead of wireless. I think the drivers are poor still and it is well worth having a try via ethernet if you haven't already.
    Otherwise you will need to wait for apple to release bonjour for windows 8 and airport utility.. which is not out yet.
    Also make sure the windows is set to home, not work or public.. even turn off the firewall.
    Open windows explorer and type the TC ip address into the address bar.. (none of which is perhaps the same.. I gave away windows at vista.. shudder)
    \\TCIPadderss.

Maybe you are looking for

  • Repairing laptops that won't boot and show the blinking caps

    Here's a little tutorial for all of you who have this annoying issue. It mostly applies to the 1 blink code (other codes have much simpler and straightforward solutions). Ok, so the code says that it's caused because of a not functional CPU. That is

  • Scheduling Problem in Productoin order

    Greetings .....                  i have on emtaerila whih has one opeartion which take 3 min for one number this opeartion is performed on a work center which available 1224 min per day .... now theroticaly ..                   1   nos               

  • Scanning an ean code

    Hello I am trying to make a voting application . When I scan an EAN code the action I want to execute is an gotoAndStop action. The question is how do a make a listner for the scanning job ?

  • Icon for file

    Hi, How to fix icon to a jar file or just for a normal file that to be placed on a desktop. If possible hellp me for Linux and windows.

  • Deleting a hotmail account

    No one knows how to delete a hotmail account. Microsoft sent me to forums and no one answers my questions. PLEASE people, I need help. Thanks, lynyrdsacul