I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

Similar Messages

Time Capsule Base via ethernet to an Airport Extreme to extend Wireless

I have set up a new Time Capsule dual band (TCBStn) as a base station (connected to the internet). I want to connect a new Airport Extreme dual band in a family room far away from the base via Ethernet. This family room has an Apple TV to which I want to stream video. I am not able to connect the AE via the Airport Utility as the Airport Utility does nor recognize the AE.

My recommendation is to configure your two base station as a "roaming" network. This will allow wired/wireless clients to connect to either and still be able to "see" each other for sharing.
Please start by powering-down all of your network components as follows:
o Power-down the modem, Time Capsule (TC), AirPort Extreme Base Station (AEBS), Apple TV (ATV), and the iMac. Note: The power-down order is not critical.
o With all of these components powered down, disconnect both the TC & AEBSn from the network, and then, perform a "factory default" reset on both to get them back to their "out-of-the-box" configuration.
o After both have been reset, remove them from power, and then, reconnect them as follows: modem > \[WAN port] > TC > \[LAN port] > \[WAN port] AEBSn, where ">" represents an Ethernet connection.
o Power-on the modem; wait at least 10-15 minutes.
o Power-on the TC; wait at least 5-10 minutes.
o Power-on the AEBSn; wait at least 5-10 minutes.
o Power-on the iMac.
o For now, leave the ATV powered-off.
In this configuration, both routers will be transmitting their own wireless network, each having a Network Name of something like: Apple Network NNNNNN, where the Ns represent the last six digits of their respective AirPort IDs.
Now, from the iMac, use the AirPort Utility (in Manual Setup) to access the TC to make the following configuration changes:
o Time Capsule > Base Station > Time Capsule Name = TC
o Time Capsule > Wireless > Wireless Mode = Create a wireless network
o Time Capsule > Wireless > Wireless Network Name = <enter the desired Network Name>
o Time Capsule > Wireless > Radio Channel Selection = Automatic
o Internet > Internet Connection > Connect Sharing = Share a public IP address
o Leave all the other default settings (for now).
o Click on Update to write the new configuration to the TC.
While still in the AirPort Utility, select the AEBSn, and then, make the following changes:
o AirPort > Base Station > AirPort Extreme Name = AEBSn
o AirPort > Wireless > Wireless Mode = Create a wireless network
o AirPort > Wireless > Wireless Network Name = <use the same Network Name that you created for the TC>
o AirPort > Wireless > Radio Channel Selection = Automatic
o Internet > Internet Connection > Connect Sharing = Off (Bridge Mode)
o Leave all the other default settings (for now).
o Click on Update to write the new configuration to the AEBSn.
You should now have a basic roaming network. Verify that your iMac can access the Internet while connected to either base station by wire or wireless. Please post back your results.

Using old airport as time capsule only via ethernet

I upgraded to a new Airport Extreme (the tall units) and I have the old flat one that I would like to use for time machine backup only. Is this possible? How should it be configured as I do not want to have it on WiFi and I will not have it connected to the router. I want the iMac to be connected to the new Aiport Extreme via WiFi. Should it connect via ethernet?

What does this have to do with the Apple TV, the forum to which it was posted?

I have a airport time capsule, an older airport extreme, and an airport express. I want to hard wire my Mac Mini to the network. What is the best arrangement of the devices? which ones should be hard wired to optimize extending the network?

I have a airport time capsule, an older airport extreme, and an older airport express. I want to hard wire my Mac Mini to the network. What is the best arrangement of the devices? which ones should be hard wired to optimize extending the network?

I am using TM Unifi with an ASUS RT-N18U Wi-Fi router. I would like to know could I use Apple AirPort Time Capsule to extend (repeater, booster) my Wi-Fi to a part of the house where the Wi-Fi signal is poor
Yes,, if you plan to connect the AirPort Time Capsule to the ASUS router using an Ethernet cable connection that will remain fixed and permanently installed at all times.
No, if you were planning to have the AirPort Time Capsule connect wirelessly and extend the Asus WiFi signal, since it would not be compatible with another manufacturer's router for that purpose.
Another way of saying the same thing here would be that if you want to extend the network wirelessly, it will take two Apple routers to do so

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

I have a 3rd party hard drive with movies on it ,it is connected to my airport extreme. The AE is connected to my tv via ethernet cable. Can I stream my movies to the Tv ?

Not without a player..
The AE is a dumb file server.. the hard disk you plug in is an even dumber hard disk.
There are no smarts in this setup.. not even DLNA. So the TV would have to be an extremely smart one to read raw files on a network drive.. none do that I know of.
A solution is WD live TV.. it can read files from just about any file source on network and play them to the TV.
Nothing apple makes will do that.. ATV is a streamer not a media player. Everything in the Apple world is tied up with itunes. So you must have a computer running itunes to use it.
You can download a more generic player for ipad, and put that as part of the network.. but you still need ATV to display the video.

Have new Airport Extreme via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicats extender shoul have same name as main network?

Have new Airport Extreme conneted via ethernet cable from HughesNet Gen4 modem. Using NetGear WN3500RP extender. NetGear asks for different names for the 2.4 and 5 GHz bands. Most of what I have read indicates extender should have same name as main network? How is it best to configure with the Airport Extreme router 802.11ac?

Different names for the 2.4 and 5 GHz networks are optional, but can be convenient for you to distinguish one from another. It's up to you.

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and

If I have an airport extreme and a time capsule is it possible for seamless switching between the 2 when a signal is weak or drops
Main reason is as I move from my first floor to my attic office and would like to place one (airport extreme)downstairs and time capsule upstairs to get complete coverage

In theory, yes. If you configure the two base station into either an extended or roaming network configuration, you should be able to walk a laptop between routers and the laptop should attempt to connect/reconnect to the base station providing the stronger signal ... but, in reality, this is not always 100% true.

HT4260 Airport extreme and time capsule connection order in a roaming network

I plan to create a roaming network with my current Airport Extreme as the primary device connected to the internet and the new Time Capsule as the secondary device in Bridge mode. The connection between AE and TC will be wired (ethernet). Then I plan to connect the PC that needs backing up to the Time Capsule with an ethernet cable. Apart from the PC-backup functionality, I'd like to use the Time Capsule as a central NAS-device in my network. All other wired network devices that need access to the NAS (Apple TV, Xtreamer) are currently connected to the primary Airport Extreme with ethernet cables. My question: is there any reason why I should consider reversing the setup order, i.e. making the Time Capsule the primary device connected to the internet and the Airport Extreme the secondary device? Would this have a positive or negative effect on Time Capsule functionality and performance in the network? Thanks in advance for your thoughts!

Your Gen3 Extreme and all TC are gigabit.. as long as you connect with the required standard cable to have a gigabit connection between the two, there will effectively be no difference. In a home network you will struggle to saturate gigabit no matter what you do. Although the difference between the two configurations is really very small.
General rule is keep whatever is using the highest bandwidth closest and directly connected to whatever it is using.. shrug.. in this case you can follow or not.. it is more a guideline.

Advice to extend range from Time Capsule - wireless and ethernet with Airport Express and Airport Extreme

Current wireless network is Time Capsule (connected to a Cisco router, 1GB switch to servers and printer 1) to Airport Express (wireless) and to Airport Extreme (wireless). Distance means poor signal at the Extreme which has 2 printers (ethernet cables) and an iMac (wireless)
Solution is to connect the Extreme to the Time Capsule via Cat 6 ethernet cable
How do I configure the TC and the Extreme?
I will keep the Express for a wireless extension to the TC

Wired Ethernet from the TC to the AirPort Extreme will result in much better performance. It sounds as if you are not configuring the AirPort Extreme correctly.
Please try the following steps carefully:
Unplug the Ethernet cable from the AirPort Exteme if it is not already unplugged. With the AirPort Extreme powered on, hold in the reset button on the Extreme for 10 seconds and release. Allow a full minute for the Extreme to restart
Connect the Ethernet cable to the WAN "O" port on the Extreme.
Click the AirPort icon at the top of the Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click on AirPort Extreme.
The example below displays an AirPort Express. You will see AirPort Extreme.
AirPort Setup will open up automatically and take a minute to analyze the network, then announce that the Extreme will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the Exterme and click Next
Wait a minute while AirPort Setup configures everything for you. When you see the message of Setup Complete, click Done.
That's it. Pretty simple. Things should be working fine now.

I have my wifi in my home with secure connection when i get connected to it ,it asks me the password and when i entered it, it shows that unable to join the network why is this happening...........

i have my wifi in my home with secure connection when i get connected to it ,it asks me the password and when i entered it, it shows that unable to join the network why is this happening...........

You are right, but how could i send it to Apple? when the phone company first replaced my iphone they had in stock alots of iphones and they just sent mine back to Apple and gave me a new one, so all i did is to give them my phone, but now how could i sent it to Apple? and i cant send it by myself, and the store wont do that, its a lost for them.. so sending it to Apple wasnt an option from the begining.
and for the record, i dont think the store where i bought it is an authorized shop.. its just a store who boughts phone's from Apple in a low price and sells it in much more money..

Connecting aiport extreme and airport express via ethernet cable ?

Is it possible to connect an airport extreme to an airport express via ethernet cable, I ask because I want to expand the range of my wifi network to the basement of my house, the floors are really thick concrete so I installed some ethernet cable runs, I hope somebody can help me, thank you.

+How do I do it ? Do I connect the modem to the airport extreme and then run the ethernet cable from one of the extreme's ethernet ports to the express ethernet on the basememt and a second cable from another of the extreme's ethernet connectors to the express on the second floor+
Yes, this is exactly correct.
To configure each AirPort Express (AX)
Open AirPort Utility, click Manual Setup
Click the Base Station tab below the icons to name your device, assign a device password and adjust time zone settings. Give each Express a separate name so you can identify then easily.
Click the Wireless tab
Wireless Mode...Create a Wireless Network
Wireless Network Name...Exact same name as your AirPort Extreme network
Radio Mode 802.11n (802.11b/g compatible) if you want to use 2.4 GHz
Channel...Automatic
Wireless Security...Exact same setting as your AirPort Extreme network
Wireless Password....Exact same setting as your AirPort Extreme network
Click the Internet icon
Change the Connection Sharing setting at the bottom to "Off (Bridge Mode)"
Click Update at the lower right and the AirPort Express will restart in 20-30 seconds
I think it is easier to configure each AirPort Express with AirPort Utility by temporarily connecting it to your computer with a short ethernet cable. Once you have saved the configuration, you can move the Express to the location that you need.
Please post back on your progress.

I have an HP LaserJet 8150N that I am trying to get connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer.

I have an HP LaserJet 8150N that I use for my work and I have had this printer for ever and it is one heck of a work horse! I am trying to get it connected via ethernet cable directly to my iMac. I always had this printer connected via a network so I don't know if I am able to connect directly with a cable since it is a network printer. I have tried to reconfigure the printer using the JetDirect menu giving it a new IP address but still no luck. If anyone could help me through this issue I would appreciate it.

moonlightcaravan wrote:
Second, seeing "connecting" and connection failed is normal. You must click on "Connect As" in the Finder window and then enter the username and password for the admin account on the other computer. That should fix things.
Thanks for responding.
When does clicking on "Connect As" happen in the process above?
After step six? Seven?
After the connection has failed?
Is this the FInder window that shows the icon of the computer you want to copy the file from?
You should see "Connect As" in the Finder near the top right of the window as shown below:
!http://blog.brothersoft.com/wp-content/uploads/2008/11/howto_copy_files_to_or_from_your_iphone02.jpg!

Connecting to Airport Express via Ethernet Cable

Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
ST

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

Connecting a Laptop to Airport Express via Ethernet Cable

I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
My question is can I make this work? After buying the Ethernet cord, all my reading of the AirPort Express manual seems to suggest that the Ethernet port on the AirPort Express is to only be used as an input port, not as an output. Is this correct?
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

AirPort Express via ethernet cable/Wireless.

I have an iMac upstairs, and want to stream music to my HI-Fi downstairs. My new AirPort Express has a green light and is found via Airport Utility on the iMac when connected to my modem (BT HomeHub, downstairs)) via ethernet cable. But once unplugged from the modem so I can use it near the Hi-Fi it is not found via wireless, and has a flashing amber light. I only want to stream music from iMac to Hi-Fi. I set it up to join the existing network - the guy in the Apple store assured me I didn't need to be connected by ethernet to the modem, that it would work via WiFi. What am I doing wrong?

Thanks to edex67 for providing the info that the Home Hub will work with WPA/WPA2 Personal security.
Please locate the Express temporarily in the same room or an adjacent room as the Home Hub.
Perform a Factory Default Reset on the Express to get everything back to a known state as follows:
Pull the Express from power
Wait a few minutes
Hold in the reset button first, and keep holding it for an additional 9-10 seconds while you simultaneously plug the power back into the Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light
Click the AirPort icon at the top of the Mac's screen and make sure that you are connected to Apple Network xxxxxx. No password is required.
Open Macintosh HD > Applications > Utilities > AirPort Utility 5.6
Click on the AirPort Express and then click Manual Setup
Click the Base Station tab below the row of icons to assign a device name to the Express, device password, and adjust Time Zone Settings. The settings should look like this:
Next, click the Wireless tab located next to the Base Station tab. Adjust settings as follows:
Wireless Mode = Join a wireless network (You might have to hold down the option key on the Mac while you click on the selection box to see the "Join" setting appear)
Wireless Network Name = Name of the Home Hub Network
Enter a check mark next to Allow Ethernet Clients if you want to enable the Ethernet port
Wireless Security = WPA/WPA2 Personal
Wireless Password = Home Hub wireless network password
Verify Password
Click the Update button at the lower right
Close AirPort Utility as soon as you see the message that the configuration has been stored on the Express
Wait 45-60 seconds for a green light
Move the Express to the desired location and power it back up, connect speakers, etc.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

Similar Messages

Maybe you are looking for