I have a first gen. ipod i turned it on and then it shut itself back off. Now wont go past the apple screen what happend?

My first gen.ipod shut off by itself and won't get past the first apple screen.When I turn it on the apple screen comes up then it shuts back off.

You should do a DFU.
Steps to DFU
Turn your device off. Press and hold the Power button until the Power slider appears. Slide it to the right to turn the device off. Wait for your device to completely power down before continuing.
Plug into your Computer.
Press the Power button. Hold the Power button for 3 seconds.
Press the Home button. After the first 3 seconds, press and hold the Home button while continuing to hold the Power button. Do this for 10 seconds.
Release the Power button. After exactly 10 seconds of holding both buttons, release the Power button but continue holding the Home button. After a few seconds, a message will appear in iTunes letting you know that the device has been detected. The device’s screen will remain blank if done successfully.
Then you should restore it and put all your info back.
*Make sure you back it up before you do this*

Similar Messages

  • I have a first gen ipod which is being recalled, and after going thru the process of registering my ipod I did not receive a barcode to send my old ipod back to apple with.  I wasn't sure if apple would send me some packaging to return the ipod.

    I have a first generation ipod nano which is being recalled, and after going thru the registration process was meant to get a barcode to send the old nano back with but it was blank.  In the registration process it also mentioned about apple sending out packaging to return the old ipod.  Just wondering if anyone has been thru this process and can offer advice?

    Yes they will send you a box with return label. I have been waiting for a month for a box. Just got off the phone with customer service and they said it would be another 3-4 weeks before I receive a box for replacement. Once I send it in it will take another 6 weeks to get the replacement after they receive it. I also hear it a 1st gen nano that will be the replacement.Apple says they were overwhelmed by the response to the recall.  Looks like they dropped the ball when they have to spend the money!

  • My ipod froze and wont go past the apple logo

    my ipod froze so i turned it off, then it turned on and now wont go past the apple logo i have tryed holding down the lock and the home screen button in together and it just restarts and stays on the apple logo, i managed to put it into disk mode, where it comes up with the conect to itunes picture, but my computer is not finding/reconising it, so there fore i can not restore it, what do i do? please help!

    How do you put it on disk mode?

  • My ipod 4G wont go past the apple logo when I turn it on - it will stay on the apple logo for few min, then blanks out and back to the apple logo.  Tried reset option/troubleshoot several times.  Also wont show up on computer at all when I plug in to USB.

    Can someone please help with my issue listed - My ipod 4G wont go past the apple logo when I turn it on - it will stay on the apple logo for few min, then blanks out and back to the apple logo.  Tried reset option/troubleshoot several times.  Also wont show up on computer at all when I plug in to USB.
    Any tips are very much appreciated.

    Place the iPod Touch into DFU mode.  This will be similar to what the factory would do to install the iOS onto new iOS devices.
    Placing it into DFU mode will allow you to "format" and install the current iOS for that device.
    To place your iOS device into DFU mode.
    First connect you iOS device to you computer.
    Open iTunes if not already open
    Now turn off your iOS device using the power swipe.
    Press the home and sleep button on your iOS device for 10 seconds.
    Release the sleep button but carry on holding down the home button.  For another 10 seconds.
    Your iOS device should now be on DFU.  Click on restore and iTunes will download the latest iOS for your device.
    Hopefully that sorts it if not, you will have to go to a service centre or call Apple Care up and get them to collect it and repair it. (replace it)  Or go into an Apple Store.

  • My ipod touch 4g 8 gigs is not turning on it wont get past the apple logo its not frozen because it turns the screen black and the apple logo please help me

    my ipod touch 4g 8 gigs is not turning on it wont get past the apple logo its not frozen because it turns the screen black and the apple logo please help me

    - Try a reset.
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Then connect to your computer and try to restore.
    - See if placing the iPod in recovery mode will allow a restore. For recovery mode see:
    iPhone and iPod touch: Unable to update or restore
    - If the logo still show all the time, let the battery fully drain. After charging for an hour try the above again.

  • , ii reset my ipod and now its stuck on the apple logo what do i do to fix it? reset my ipod and now its stuck on the apple logo what do i do to fix it?

    i reset my ipod and now its stuck on the apple logo what do i do to fix it? reset my ipod and now its stuck on the apple logo what do i do to fix it?

    Try:
    - iOS: Not responding or does not turn on
    - Also try DFU mode after try recovery mode
    How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
    - If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - Try on another computer                            
    - If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
      Apple Retail Store - Genius Bar                              

  • After I have been talking on my iPhone 6 for awhile and then want to go to speaker phone, I cannot find the speaker icon.  Any help?

    After I have been talking on my iPhone 6 for awhile and then want to go to speaker phone, I cannot find the speaker icon.  Any help?

    Here's the situation.  I received a text while I was talking on the phone.  Went right to text, then could not get back to the screen.  After trial and error, I discovered a little green message at the top of the phone that said "Touch to return to call".  Problem solved.

  • HT4528 i have restored my iphone 4s but now it just keeps staying at the apple screen. what should i do?

    i have restored my iphone 4s but now it just keeps staying at the apple screen. what should i do?

    Take your phone back to the store where you got it. Tell them if they can't get it activated, you want your money back. Then purchase a new iPhone 4S.

  • I tried to update my ipod touch to ios 6 and now it wont boot past the apple icon. please help

    I tried to update my ipod touch to ios 6 and now it wont boot past the apple icon. please help

    Put your ipod in recovery mode and then restore your software again.

  • My iphone just shut off and now wont turn back on.. is stuck on the apple screen.

    my iphone 3gs is locked up...  just shut off in the middle of a text...  tries to turn it back on and it wont go past the aple screen??

    Try resetting your iPhone by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.
    If you can't do that, try Recovery Mode... http://support.apple.com/kb/HT1808

  • Recently my ipod touch (old version ) was not working correctly, so i deleted everything from it---expecting to start fresh, however when i start  it up it continues to stay on the apple screen, what is wrong with my ipod and how can i fix it ?

    my  ipod doesn't allow me to do the thiings it used to. It would change the time and date and everytime i'd turn it to the correct date it would go back when i clicked a new app. it wouldn't load apps corectly because of this date and time problem. So i decided to erase everything and start fresh. But now it won't even load properly it just stays on the apple screen with the loading spin thing stuck. someone please guide me into fixing this problem

    Try:
    - iOS: Not responding or does not turn on
    - If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
    - If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

  • My imac is making low beeping noises when I turn it on and wont go past a grey screen; whats wrong?

    When I turn on my computer it goes strait to a grey screen with the apple and starts a low beeping. The beeping does not stop so I rebooted it several times and everytime it turns back on, it starts to beep again.
    What could be the problem?

    Intel-based Macs: Resetting the System Management Controller (SMC)
    Note: It is possible that the SMC could encounter an issue that may cause  unusual system behavior typically related to the symptoms described  below.  In some cases, resetting the SMC may be the only correct method  to resolve the issue, however, an SMC reset should only be attempted  after all other standard troubleshooting has been performed.
    Before Resetting the SMC
    Try each of the following steps in this order before you reset the SMC.  Test the issue after completing each troubleshooting step to determine if the issue still occurs.
    Press Command + Option + Escape to force quit any application that is not responding.
    Put your Mac to sleep by choosing the Apple () menu from the upper-left menu bar and then choosing Sleep.  Wake the computer after it has gone to sleep.
    Restart your Mac by by choosing the Apple () menu from the upper-left menu bar and then choosing Restart.
    Shut down your Mac by by choosing the Apple () menu from the upper-left menu bar and then choosing Shut Down.
    If your Mac appears to be running normally but isn't responding, force the computer to shut down by pressing and holding the power button for 10 seconds. Note: You will lose any unsaved work in any open applications.
    For Mac portables experiencing issues related to the MagSafe power adapter and/or battery, try:
    Unplug the MagSafe power adapter from the Mac and the wall power socket for several seconds.
    Shutdown the Mac.  Physically remove and re-insert the battery (if it's removable) and startup the Mac.
    If the issue is still not resolved after following the troubleshooting items above, an SMC reset may be necessary.
    After performing normal troubleshooting, these symptoms may indicate that an SMC reset may be necessary:
    Fans
    The computer's fans run at high speed although the computer is not experiencing heavy usage and is properly ventilated.
    Lights
    The keyboard backlight appears to behave incorrectly (on Mac computers that have this feature).
    The Status Indicator Light (SIL) appears to behave incorrectly (on Mac computers that have an SIL).
    Battery indicator lights, if present, appear to behave incorrectly (on portables that use non-removable batteries).
    The display backlight doesn't respond correctly to ambient light changes on Mac computers that have this feature.
    Power
    The computer doesn't respond to the power button when pressed.
    A portable Mac doesn't appear to respond properly when you close or open the lid.
    The computer sleeps or shuts down unexpectedly.
    The battery does not appear to be charging properly.
    The MagSafe power adaptor LED doesn't appear to indicate the correct activity.
    System Performance
    The computer is running unusually slowly although it is not experiencing abnormally high CPU utilization.
    Video
    A computer that supports target display mode does not switch into or out of target display mode as expected.
    A computer that supports target display mode switches into or out of target display mode at unexpected times.

  • TS1702 how do I find apps for the Ipod version 3.1.3 for the Ipod touch in Itunes?! Is there no more apps for the first gen Ipod? I've tried and tried and googled and can't find a single app that will install on this old Ipod. Please help!

    I recently had an Ipod first gen with Ios 3.1.3 fixed and am in need of finding games for my son to play, but I cannot for the life of me find any games or any apps that can be installed on this Ipod! every time I download something and try to install it, Itunes keeps telling me that the app requires a newer Ios! There isn't any new Ios version for this ipod that I can find. Itunes won't install any newer version of Ios, and no new apps can be found that can be installed. Please help me.

    iOSSearch - search the iTunes store for compatible apps.
    Vintapps 3.1.3 - paid app.
    Apple Club - filter apps by iOS version.

  • Which cable (original apple usb or bmw y) shall i use to connect my 4th gen iPod photo 60 gb to bmw f10 (with com box) is it going to work with the apple usb cable and how long does it take till I can access the 33gb content via the bmw display?

    Which cable (original apple usb or bmw y) shall I use to connect my 4th gen iPod photo 60 gb (old but still working ok) to bmw f10 (with com box), build december 2010 > is it going to work with the apple usb cable and if so, how long does it take till I should be able to access the 33gb content via the bmw display?
    Alternatively: How long does it take if I would have to use the bmw y cable till I can access the 33gb content via the bmw display?

    Which cable (original apple usb or bmw y) shall I use to connect my 4th gen iPod photo 60 gb (old but still working ok) to bmw f10 (with com box), build december 2010 > is it going to work with the apple usb cable and if so, how long does it take till I should be able to access the 33gb content via the bmw display?
    Alternatively: How long does it take if I would have to use the bmw y cable till I can access the 33gb content via the bmw display?

  • When I try to turn on my old ipod nano it will flash and then go black again. only when its hooked up to the computer. whats wrong with it and how do I make it work?

    Ok. My brother has an old Ipod nano. It's the tall one with the tiny screen. Anyway, he tried to turn it on one day and it just flashed white and then went black again. We tried everything we could and it still wont work. Now it wont flash unless it is plugged up to the computer. How do I fix it so it will work again?

    Have you checked the volume button? It might be physically stuck. To determine whether a hardware repair is needed, you need to follow these steps:
    1. Try doing a hard reset:
    Press and hold both the Home button and the Sleep/wake button simultaneously for about 15 seconds and release when the Apple logo appears.
    After that: test the device to see whether the issue is solved.
    2. If the issue is not solved, you should backup the device and restore it as new.
    In that case, use: http://support.apple.com/kb/HT4137
    NB: set up as a NEW device because a software issue will be in the backup.
    If the issue persists after restoring as new, you should offer the device for service.
    If you get specific error messages/codes in iTunes when updating/restoring, check this: http://support.apple.com/kb/ts3694 for causes and solutions
    Good luck
    Stijn

Maybe you are looking for

  • Breaking up a long query

    Hello, I am creating a PL/SQL package that produces a report based on the selection of different accounts and dates from a text area and a drop down menu. When I select accounts from the text area, it should run a query to generate a report, i.e. if

  • Viewing ipad apps on TV

    I have an adaptor that enables me to watch iTunes purchases on my TV through my ipad2 (the 3 connections are red/white/yellow ones (forgive my tech know how!). This set up works fine for anything stored in videos on the ipad2, but is it possible to c

  • Problem in Query Migration

    Hi All, When I am trying to open the 3.0B query designer in BI 7.0 it is giving the below message Obsolete server version. You need SP5 or higher version for the query designer But we have installed the GUI 7.1 and the support package is 5 When I am

  • Unable to create a new asset

    When I try to create an asset using transaction code AS01 I get a message SYST: Asset number 44000000 exists already(Contact your system specialist). The number 44000000 is already an asset and what should have happened was for the system to generate

  • What is the current version of the iPod firmware?

    Hello, I'm currently running the "other OS" and can't get iTunes. Could someone please tell me what the current version of the iPod firmware is? This way, I'll know whether I need to go to a Mac or PC computer to update the firmware of my 5th gen iPo