I have a LaserJet Pro P1606dn - the second page prints upside down when using the duplex print optio

Operating system Windows 7 32 bit.  I have re-installed the printer an I have downloaded and applied the most recent drivers from the HP site.  The built in set-up shows the settings correctly as duplex on and bind on the long edge but the second page continues to print upside down i.e. it seems to always print as binding on the top edge.
However when I print from my iPad via Airprint the duplex print works perfectly!

IF you are using a printer with 2-sided printing, in the expanded print dialog you will have a selection for long-edge binding OR short-edge binding. Whichever setting you have set, switch to the other one.
Walt

Similar Messages

  • How do I move an icon from the second page of my home screen to the first page  and vice versa?

    How do I move an icon from the second page of my home screen to the first page and vice versa?

    Hold an icon down until they all wiggle.
    Drag it wherever you want it.

  • Photoshop CS6 shuts downs when using the move tool

    Photoshop CS6 shuts downs when using the move tool. It seemas to run fine until i try and use the move tool. PS worked fine just a few weeks ago and now it has this issue. What can i do to resole this issue?
    Thnaks,
    System Specs
    Windows XP Home SP3
    AMD Atholon 64 X2 Dual
    2GB RAM
    Video Cards
    Radeon 7200
    NVIDIA GeForce 8400GS

    Two displays are OK on one adapter, Two displays adapters are not OK. http://helpx.adobe.com/photoshop/kb/gpu-opengl-support-photoshop-cs4.html
    7. If you are using more than one video adapter, remove the additional cards.
    Multiple video adapters can cause problems when OpenGL and Photoshop use the GPU. It's best to connect two (or more) monitors into one video adapter. If you have to use more than one video adapter, make sure that they are the same make and model. Also make sure that they both support the same versions of OpenGL and Shader Model. Otherwise, crashes and other problems can occur in Photoshop.
    Note: Using two video adapters does not enhance Photoshop's performance.

  • Software shuts down when using the lightning effects filter. Help!

    Software shuts down when using the lightning effects filter. Help!

    Have you done a Forum search yet?
    Is your GPU driver up to date?
    What are your version of Photoshop, OS and GPU anyway?

  • How do I set up pages to print a 5x7 catalog using doubled sided printing. When I try this layout the inside pages are upside down?

    I am trying to print a 5 x7 catalog. When I print it out using doubled sided the inside pages are upside down. Is there a way to setup and print using a 5x7 format?

    If your printer does duplex printing (i.e. you're not re-feeding the pages manually), there may be a setting in the print dialog. My Brother color laser has these option when I check the two-sided box. If you see something similar, test the various options & make a note of what works. It took me so many tries to figure out what they meant by long- or short-edge binding!
    If you're using something like CocoaBooklet or another program to create a booklet, see if it has an option to turn the second side upside down.

  • MBP suddenly shuts down when using the superdriveP shuts down when u

    Randomly my husband:s MBP shuts down when using the super drive. What could be the cause of this?
    Appreciatte your Help

    Yeah, I hope it is just a firmware-problem. AND that Nokia will release an update soon. The version on my phone now is 021.013, and it is from July. A firmware update is long overdue now, especially after all the other problems reported with this phone. And btw I have turned the phone on and off several times without this helping to fix the radio-issue...
    I guess I will have to return the phone soon, if Nokia is unable to release a fixed firmware.

  • What is the best way to avoid latency when using the io plug in?

    What is the best way to avoid latency when using the io plug in?

    Hi colin a.
    Welcome to the Support Communities!
    The article below may be able to help you with this.  Click on the link to see more details and screenshots. 
    Logic: About I/O buffer size and monitoring latency
    http://support.apple.com/kb/ht1314
    Cheers,
    - Judy

  • HT202879 recently saved a Pages document to Dropbox. Now I cannot open it in the new Pages app, and I cannot use the previous Pages version to open it. Attempting to open the document gives me a flash of a page and then the program crashes. Anybody have a

    I can go to Time Machine and find the document, even read it in Time Machine, but when I try to restore this version I get the same crash. I cannot open with Text or RTF. Preview opens a fuzzy version and can save out as a .PDF, but when I try to convert the .PDF to Word I get a bunch of unusual characters. Any help anyone can give would be greatly appreciated

    OK, I've tried all these tips. Here's what I finally have to do: I open Time Machine. I click on the Pages file and open the Pages file in the Time Machine window. (Restore does not work; nothing works).
    When the Pages file opens, I begin taking screenshots using shift-command-3. I take shots of all 200+ pages of this document. The screenshots are saved to my desktop.
    I then move all 200+ screenshots into one folder, because, face it, that's too many icons to work with on one desktop screen.
    Then I select all the screenshots in the folder at once and open them all in Preview. Then I crop every screenshot using command-K, and save using command-S, and then close that image using command-W.
    When I have cropped all 200+ screenshots, I go back through the folder one by one and adjust the color on each one, moving the mid-range color up to about 75% and the sharpness filter up to about 75%, in order to compensate for the fuzzy image of the screenshot. You can't create a searchable PDF with an image that fuzzy. I do this one by one.
    I make sure everything is saved.
    Then I open all 200+ edited screenshots in Preview and print them out.
    Then I take the 200+ pages of this ****** Pages file and run them through my scanner, making searchable 600 dpi PDFs.
    Then I go to each of the 200+ PDFs and highlight the text, copy, and paste into a NEW word processing document.
    If I'd had 300 pages like the last manuscript, or 700 pages like the one before that, I would have created an Automator program to do all that, but hey, this is not the kind of **** you expect from Apple. Really.  It's taken all week.
    So thanks for your help guys, but no other suggestions worked. I tried to force a download of the file from Dropbox, but got the same result. Besides, my Dropbox folder is saved locally on my harddrive, so it's not their fault. In fact, there is no data in the Dropbox folder under this file name, only preview files. Somehow the Time Machine will open the complete Pages file while in Time Macine, but will not import the saved Time Machine version to the working desktop because it is a preview (i.e., not Preview) image. This is a Pages problem, not a Dropbox problem. Pages did not save the full file.
    If anybody knows a better way to do this, I'd like to know about it. If anybody knows whether I will ever be able to trust Pages again, I'd like to know that too.

  • BIP Outputting to PDF the second page starts 1 line higher than the first

    Hello -
    Im using Embedded BI Publisher 10.1.3.4.2 to print a document to PDF. Once I print 45 lines on the first page, I page-break to continue on page number 2.
    For some reason the page 2 output starts 1 line above where it starts one page 1. It's as if the header changes between pages....?
    I cannot figure this out. I need both pages to start at the same position on every page.
    Any ideas?

    Thank you that solved the issue.
    I had spaces in some BIP variables (for loops, etc) on the first line. Once I removed the spaces the template worked correctly.
    Example
    [FOR EACH GROUP] [GROUP BY] [VARIABLE]
    Needed to be:
    [FOR EACH GROUP][GROUP BY][VARIABLE]

  • Slow down the Creative Entertainment Center Fast Foreward when using the X-FI Remo

    Hello,
    When watching videos on my computer using the?Creative Entertainment?Center app and the remote with my X-FI SoundBlaster card the fast forward goes from zero to ludicrous speed instantly. I usually end up fast forwarding half way through the file without intending to. Is there a setting or registry or any other adjustment I can use to slow this down to a sane level? A 30 second skip for instance would be wonderful!
    Thanks!

    Creative doesnt seem to hav plans to release Entertainment center for Audigy 2 ZS. But theres a way to install and use Entertainment center with AUDIGY 2 ZS Platinum/Pro. I first installed the Audigy 4 Modded PAX drivers for Audigy2 ZS with all softwares(i downloaded Audigy 4 ISO) , Then i uninstalled the drivers and reinstalled Audigy 2 ZS drivers , and again installed Entertainment Center, Guess what now Audigy 4 doesnt prompt me that i dont have the required HARD WARE before installation starts, and i can install ny Audigy 4 software(nothing much new though , only Entertainment center and Smart Recorder). and i am now enjoying Entertainment CENTER with my Audigy 2 ZS Platinum Pro and with Audigy 2 drivers!!!!.
    I think its not proper on part of CREATIVE not to release Ent. Center for Audigy 2, as the IO box and remote control of Audigy 2 and Audigy 4 are the same( RM-500 remote). so wats the point in keeping Ent. Center just for Audigy 4 and Up?
    BELOW IS MY ANALYSIS OF ENTERTAINMENT CENTER, just giving the pros and cons so that Audigy 2 Platinum/Pro Users can decide whether its GOOD or NOT
    On the PLUS SIDE
    + it has nice interface
    + Good handling of playlists
    +DVD Playback
    +Slideshow and presentation support
    On the NEAGATIVE SIDE
    - Every time u want to perform PAUSE, NEXT TRACK, PREVIOUS TRACK operations the Ent. Center pops up as a FULL screen app. interupting u r current TASK
    - Also it is not integrated with MEDIA SOURCE Player,(i.e when u start playing song with ent. center it doesnt get layed with MEDIASOURCE so not DTS Neo:6 Playback!!!)
    -Even the Press of CMSS button takes u to the full screen app. again causing INTERRUPTION!!!!!
    - Doesn't Have a SEARCH option to search for tracks from thee Library
    - No BASS/TREBLE/BALANCE Control thru. it
    Message Edited by nvpower on 09-30-2005 06:39 PM

  • E52 - Shuts down when using the radio

    Hi!
    I have discovered that my E52 shuts down whenever I try to use the radio. After 10-20 seconds of use the phone shuts down, and restarts itself (without turning the radio back on).
    The strange thing is that this only seems to happen when I use the radio here in Norway (where the phone was bought). I have used the radio in London and Berlin without this problem, but every time I try to use the radio in Norway the phone shuts down. Seems like there's a conflict with the RDS maybe??
    Does anyone have a way of fixing this?
    Jim 

    Yeah, I hope it is just a firmware-problem. AND that Nokia will release an update soon. The version on my phone now is 021.013, and it is from July. A firmware update is long overdue now, especially after all the other problems reported with this phone. And btw I have turned the phone on and off several times without this helping to fix the radio-issue...
    I guess I will have to return the phone soon, if Nokia is unable to release a fixed firmware.

  • I bought an itunes giftcarad to pay if off. I redeemed it and everything. When i try to buy something it says i can't and it takes me to the billing page. I can't use the credit card and i already redeemed the card. How do i use my store credit to pay it

    I need help. i bought a itunes card and i reddemed it to pay off my debt. how can i use store credit to pay it off ?

    If you mean use the balance of the credit and you don't have enough to buy iTunes media, you will have to purchase and redeem another gift card to make up the difference.

  • How can i get rid of the print dialog box when using api to print an html file

    i am using the systemshell.vi provided by labview the VI is working fine but it will open a dialog box for printer selection and properties. i would like to hide that dialog box and have it print to the default printer with the default properties

    ShellExec is part of lvwutil and merely calls a function in Shell32.dll. There is nothing about the function call that controls the display of the printer dialog. I think that what shell32.dll does when it prints (just like right clicking on the file) is print the file according to what is defined about that file type in Windows Folder Options. On my Win2K system, the print application is defined as "C:\Program Files\Microsoft Office\Office\msohtmed.exe" /p %1. If I remove the /p, then Word starts up and in order to print, I get a printer dialog when choosing Print from the File menu. So it seems like the printer dialog is entirely dependant on the application that does the printing. I get no dialog when I use the VI to print a .txt file. I
    nstead of using shell32, you might want to try some ActiveX method or property of an application like Internet Explorer that can open and print an html file.

  • In fullscreen mode, is there a way to prevent the page from shifting down when displaying the menu and tabs?

    In fullscreen mode (F11), when moving the mouse toward the top of the screen to display the tabs & stuff, the page displayed is shifted down. This makes it annoying when returning down with the mouse - you want to reach a certain link, for example, but your target gets shifted up once the tabs & stuff is hidden back.
    Is there any way to make the tabs & stuff display 'above' the page content, like on another layer?

    Is it the web page display that is changing its own position, or is it something
    about the toolbars that is pushing the page down? I have the same issue with
    my browser using an add-on to show a multiple line bookmark bar.

  • Photoshop Elements 9 shutting down when using the Spot Healing Brush

    Hello! I recently downloaded and
    installed the PSE 9 on my PC. Obviously I wanted to check out it's possibil
    ities and especially the Spot Healing Brush. The program seems to work fine until I want to use the Spot Healing Brush
    As soon as I try to apply something to a picture, I get the message something is wrong with "photoshopeditor.exe" and needs to shut down the program.
    That's really annoying and hopefully someone may have the answer and solution why it does this. I run the program on Windows XP (SP3).
    I really appreciate your help. Best regards, CharlesHHH.

    Hello MTSTUNER,
    Somehow my post showed up twice. Anyway...just updated to 9.01 and problem solved!!
    Thanks so much for your quick feedback. Much appreciated. Will now go into exploring its possibilities.
    Best regards,
    CharlesHHH

Maybe you are looking for

  • Hp eprint set up issues with non hp printer

    HI I have a hp pavillion p7 1414pc desktop with windows 8.  There are also 3 laptops in the house  that are Toshibas.  Two use also windows 8 bought the week after the desktop one is a year and a hapf old using windows 7.  They are all networked for

  • 19 items on a menu and each has text, image and price. HELP???!!!

    I have a UITableView with a menu on it. I would like to have a description, picture, title and price for each item. there are 19 items so i figured that creating 19 views in the storyboard would not work. Is there a way of doing this? I have the head

  • Transaction to see the Open stock transfer order for the plant

    HI , i need to develop one report in that client to make the report for the all open stock transfer order & the cost of the open stock transfer order for the plant . I need how to cretae the stock transfer order for the material , whci material maste

  • Drawing On Chart But It's Disappearing

    I created a column chart and added an annotation element to it: [code] <mx:annotationElements>         <mx:CartesianDataCanvas id="chartCanvas"/> </mx:annotationElements> [/code] I added a creation complete method to draw on the canvas. The following

  • DBMS_SHARED_POOL.KEEP -- give nothing to performance ???

    I want to know, how significant is DBMS_SHARED_POOL.KEEP to performance, but I haven't got better performance. I had tested before and after pinning it into shared_pool. State is : CREATE TABLE scott.test(fld1 number(2),fld2 number(2)); CREATE OR REP