I have a mid-2009 MBP and I've been using my BOSE Companion 20 with it for about half a year now. It was fine until recently, when i want to adjust the volume using the pod on the BOSE Companion 20, it will cause like a surge in volume, spiking it up
I have a mid-2009 MBP and I've been using my BOSE Companion 20 with it for about half a year now. It was fine until recently, when i want to adjust the volume using the pod on the BOSE Companion 20, it will cause like a surge in volume, spiking it up and down. It will not stablise itself! It's very fustrating. Anybody with the same issue?
I have the BOSE Companion 5 speakers and have had the same problem. I've searched everywhere and gotten nowhere. My speakers are way past their warranty, so calling Bose would probably get me no where either. Only thing I can think of is that the speakers overheat which causes the spikes in the volume. I've tried unplugging them for a few minutes and then plug them back on. The problem does go away, but after about 5 minutes, same problem.
Similar Messages
-
I recently bought a new tower with windows 8.1 everything was fine until yesterday when I went to watch a video that someone had posted, the sound was there but the screen was all green everything I try to watch has a green screen, I have gotten rid of the green screen but now the video won't load to watch. it tells me I have to upgrade flash player but my computer tells me its already embedded or something like that in windows 8.1. can you help.@marks93255255 or [email protected]!
If other devices can connect to the network without problems, it means that the router can provide wireless internet. For this situation, an isolation process is needed to be able to find a fix.
Was the computer tested to connect through Wi-Fi before you bought it?
Did you do Mac address filter on your router?
Make sure that the router is using WPA/WPA2 or WPA2 encryption type just like what Chester has recommended. If your router is already set to that security type, you may test by disabling the wireless security of the WI-Fi router. Check if it will connect or not.
Another thing to check is the properties of your wireless connection. To do that, Go to Network and Sharing center > Click change adapter settings > right click “Wireless” > go to Properties> click Internet protocol IPV4> check the Properties button below > make sure that it’s set to both Obtain IP automatically and Obtain DNS server automatically.
Feel free to update here so everybody in the community can help. -
My iMac (running Lion 10.7.3) is connected wirelessly to a Laserjet 2550. This has operated fine for a long time, but now the printer cannot be found when Time Machine back ups are taking place - Bonjour does not show any devices being available when Time Machine is running. Does anyone know the cause & remedy please?
Your points match mine pretty well,though here are some thoughts:
1. I thought about this theory myself this morning (iTunes possibly causing more issues), but I haven't been able to verify it.
2. When I set up a new user it seemed better for a while, but the issue croppped back up. Yesterday I fully wiped the machine and reinstalled from scratch. I did not reimport my user from TimeMachine, but the problem has come back. My thinking was that I might have some really old software or prefs hanging around causing the issue. No dice.
3. This is my current theory of the issue, so my next step will be to pull the RAM from Crucial and see how the system behves. IF that doesn't eliminate the problem, I'll pull the factory installed RAM and replace it with the 3rd party RAM. The odd thing is how many people seem to have similar issues - I know two personally, and have seen several posts on forums. I think the most common point for this happening was the 10.7.2 update, which would point to software as the culprit.
4. That matches my experience.
My hope is that this will be repaired in the forthcoming 10.7.3 release (current production version is 10.7.2), but otuside of what I noted above, I'm at a loss. -
MY iPod broke help
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order. I suspect whatever caused the broken screen progressed.
Apple Retail Store - Genius Bar -
What version of windows can I get if I have a mid 2009 iMac and an os of Snow leopard (10.6.3)
I want to play games on windows so I would like to use boot camp rather then a portal.
Windows 7.
-
When Firefox 8.0 installed it has automatically changed my address bar default search engine to Yahoo7 which is crap. I can not change this back. So when I start FF it opens to my google home page, when I type a subject and search the results are displayed in a Yahoo 7 results page, not google. I am not talking about my default home page or the search bar to the top right. This is still google.
The settings in about:config do nothing.
This was fine until FF 8.0.Thanks dmcritchie,
Nice effort but that answers a different question about fixing the add-on Yahoo toolbar.
Pernich and I want to know; If you type search criteria directly into the address bar and hit enter, how to change that search engine from Yahoo to Google.
Otherwise I too will go back to using Google Chrome, even though I really like FF8.0
please help -
[SOLVED] Mid 2009 MBP - nvidia nonfree drivers
- X server looking for nouveau
Hi all
So this is my first post on here but I have been looking on the net to find a resolution to the following for the past week or more; I have been using Ubuntu for a number of years now but would still recon my experiance in linux is still in the realm of beginner.
I have a Mid 2009 MBP with Nvidia 9600m gt and 9400m; the problem i face is getting X to start.
NOTE: Currently I'm running Manjaro 3.10.30 (clean install) as it couldn't get the pure Arch live to boot, didn't have time to investigate that, maybe in the comming weeks.
The Xorg.0.log states that it is trying to load a nouveau module
[ 11.610]
X.Org X Server 1.14.5
Release Date: 2013-12-12
[ 11.610] X Protocol Version 11, Revision 0
[ 11.610] Build Operating System: Linux 3.12.6-1-ARCH x86_64
[ 11.610] Current Operating System: Linux manjaro 3.10.30-1-MANJARO #1 SMP Fri Feb 14 06:07:50 UTC 2014 x86_64
[ 11.610] Kernel command line: BOOT_IMAGE=/vmlinuz-310-x86_64 root=UUID=d6202b98-312c-40e4-ba98-467a4f6b41c7 rw nomodeset
[ 11.611] Build Date: 08 January 2014 01:35:51PM
[ 11.611]
[ 11.611] Current version of pixman: 0.32.4
[ 11.611] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 11.611] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 11.611] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Mar 13 18:55:57 2014
[ 11.611] (==) Using config file: "/etc/X11/xorg.conf"
[ 11.611] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 11.611] (==) ServerLayout "Layout0"
[ 11.611] (**) |-->Screen "Screen0" (0)
[ 11.611] (**) | |-->Monitor "Monitor0"
[ 11.612] (**) | |-->Device "Device0"
[ 11.612] (**) |-->Input Device "Keyboard0"
[ 11.612] (**) |-->Input Device "Mouse0"
[ 11.612] (==) Automatically adding devices
[ 11.612] (==) Automatically enabling devices
[ 11.612] (==) Automatically adding GPU devices
[ 11.612] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 11.612] Entry deleted from font path.
[ 11.612] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 11.612] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 11.612] Entry deleted from font path.
[ 11.612] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 11.612] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/,
/usr/share/fonts/OTF/,
/usr/share/fonts/Type1/
[ 11.612] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 11.612] (**) Extension "Composite" is enabled
[ 11.612] (**) Extension "RENDER" is enabled
[ 11.612] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
[ 11.612] (WW) Disabling Keyboard0
[ 11.612] (WW) Disabling Mouse0
[ 11.612] (II) Loader magic: 0x7fac20
[ 11.612] (II) Module ABI versions:
[ 11.612] X.Org ANSI C Emulation: 0.4
[ 11.612] X.Org Video Driver: 14.1
[ 11.612] X.Org XInput driver : 19.1
[ 11.612] X.Org Server Extension : 7.0
[ 11.612] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 11.612] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 11.615] (--) PCI:*(0:2:0:0) 10de:0647:106b:00b0 rev 161, Mem @ 0xd4000000/16777216, 0xb0000000/268435456, 0xd2000000/33554432, I/O @ 0x00003000/128, BIOS @ 0x????????/524288
[ 11.615] (--) PCI: (0:3:0:0) 10de:0863:106b:00af rev 177, Mem @ 0xd6000000/16777216, 0xc0000000/268435456, 0xd0000000/33554432, I/O @ 0x00002000/128, BIOS @ 0x????????/131072
[ 11.615] Initializing built-in extension Generic Event Extension
[ 11.615] Initializing built-in extension SHAPE
[ 11.615] Initializing built-in extension MIT-SHM
[ 11.615] Initializing built-in extension XInputExtension
[ 11.615] Initializing built-in extension XTEST
[ 11.615] Initializing built-in extension BIG-REQUESTS
[ 11.615] Initializing built-in extension SYNC
[ 11.615] Initializing built-in extension XKEYBOARD
[ 11.616] Initializing built-in extension XC-MISC
[ 11.616] Initializing built-in extension SECURITY
[ 11.616] Initializing built-in extension XINERAMA
[ 11.616] Initializing built-in extension XFIXES
[ 11.616] Initializing built-in extension RENDER
[ 11.616] Initializing built-in extension RANDR
[ 11.616] Initializing built-in extension COMPOSITE
[ 11.616] Initializing built-in extension DAMAGE
[ 11.616] Initializing built-in extension MIT-SCREEN-SAVER
[ 11.616] Initializing built-in extension DOUBLE-BUFFER
[ 11.616] Initializing built-in extension RECORD
[ 11.616] Initializing built-in extension DPMS
[ 11.616] Initializing built-in extension X-Resource
[ 11.616] Initializing built-in extension XVideo
[ 11.616] Initializing built-in extension XVideo-MotionCompensation
[ 11.616] Initializing built-in extension XFree86-VidModeExtension
[ 11.616] Initializing built-in extension XFree86-DGA
[ 11.616] Initializing built-in extension XFree86-DRI
[ 11.616] Initializing built-in extension DRI2
[ 11.616] (II) LoadModule: "glx"
[ 11.616] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 11.638] (II) Module glx: vendor="NVIDIA Corporation"
[ 11.638] compiled for 4.0.2, module version = 1.0.0
[ 11.638] Module class: X.Org Server Extension
[ 11.638] (II) NVIDIA GLX Module 331.49 Wed Feb 12 20:17:10 PST 2014
[ 11.638] Loading extension GLX
[ 11.638] (II) LoadModule: "nouveau"
[ 11.638] (WW) Warning, couldn't open module nouveau
[ 11.638] (II) UnloadModule: "nouveau"
[ 11.638] (II) Unloading nouveau
[ 11.638] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 11.638] (EE) No drivers available.
[ 11.638] (EE)
Fatal server error:
[ 11.638] (EE) no screens found(EE)
[ 11.638] (EE)
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 11.638] (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 11.638] (EE)
I have uninstalled all nouveau packages using the following page to help me; https://wiki.archlinux.org/index.php/NVIDIA
The following is the output of
$ pacman -Qs nvidia
local/libvdpau 0.7-1
Nvidia VDPAU library
local/linux310-nvidia 331.49-1 (linux310-extramodules)
NVIDIA drivers for linux.
local/mhwd-nvidia 331.49-1
MHWD module-ids for nvidia 331.49
local/mhwd-nvidia-legacy 304.119-1
MHWD module-ids for nvidia 304.119
local/nvidia-utils 331.49-1
NVIDIA drivers utilities
I am also including my xorg.conf created with
$ nvidia-xconfig
# nvidia-xconfig: X configuration file generated by nvidia-xconfig
# nvidia-xconfig: version 304.119 (buildmeister@swio-display-x64-rhel04-14) Fri Jan 17 10:35:46 PST 2014
Section "ServerLayout"
Identifier "Layout0"
Screen 0 "Screen0" 0 0
InputDevice "Keyboard0" "CoreKeyboard"
InputDevice "Mouse0" "CorePointer"
EndSection
Section "Files"
EndSection
Section "InputDevice"
# generated from default
Identifier "Mouse0"
Driver "mouse"
Option "Protocol" "auto"
Option "Device" "/dev/psaux"
Option "Emulate3Buttons" "no"
Option "ZAxisMapping" "4 5"
EndSection
Section "InputDevice"
# generated from default
Identifier "Keyboard0"
Driver "kbd"
EndSection
Section "Monitor"
Identifier "Monitor0"
VendorName "Unknown"
ModelName "Unknown"
HorizSync 28.0 - 33.0
VertRefresh 43.0 - 72.0
Option "DPMS"
EndSection
Section "Device"
Identifier "Device0"
Driver "nvidia"
VendorName "NVIDIA Corporation"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Device0"
Monitor "Monitor0"
DefaultDepth 24
SubSection "Display"
Depth 24
EndSubSection
EndSection
Output of
$ lspci -k | grep -A 2 -i "VGA"
02:00.0 VGA compatible controller: NVIDIA Corporation G96M [GeForce 9600M GT] (rev a1)
Subsystem: Apple Inc. Device 00b0
Kernel driver in use: nvidia
03:00.0 VGA compatible controller: NVIDIA Corporation C79 [GeForce 9400M] (rev b1)
Subsystem: Apple Inc. Device 00af
Kernel driver in use: nvidia
Also tried the 304 set but to no avail.
I noticed just before grabbing my the above files/data via ssh that the /home/[username] directory is still the default user, "Manjaro" in this case. but this is probably in part due to X server not being able to start.
If anyone has any idea what direction i should take, please let me know. I have an image/backup of my Ubuntu 12.04 which i might have to restore to get the equivalent data, but i would rather fix this without it.
P.S. Not sure if this is the correct section for this topic.
Last edited by DoveDev (2014-03-14 18:34:15)This is one of them times I should have wrote down what steps i had completed and had not, I reread the information on this page, http://wiki.manjaro.org/index.php?title … on_Startup. Obviously i missed a vitel step while i was half asleep a few nights ago... Anyway This is solved.
P.S. I will be getting a refurbished Dell Latitude e7440 next week and I will be playing with it and a pure Arch experiance, can't wait. Catch you later. -
Replacement options for keys on mid-2009 MBP
i have a mid-2009 MBP that i am extremely unhappy with and which i /was/ going to just give to my mom but it acts so oddly that i am afraid she will get too confused and won't be able to use it.
/anyway/ i had this thing in to the genius bar and asked them to replace all the keys as there are a lot of these that are very wobbly and make typing sort of a challenge. the technician asked me to tell him which /specific/ keys were a problem - i didn't sit down to test this - and then proceeded to give me some kind of song and dance explaining the technical reasons why the keys would fail and he assured me that as long as there was not some failure with the mechanism under the keys that they would replace the keys for the life of the machine at no charge.
two questions:
1. i have written down the 23 keys that feel like they are hard to work with and i am wondering if it is unreasonable to expect them to just replace all of them now so i (or the person i give the machien to) won't have to deal with this periodically.
2. is it in fact the case that i should expect to get other keys fixed for free when they go bad?
3. is there some reason why the technician at the genius bar may not have wanted me to do another repair on this machine within the warranty period since i have had it in complaining about various issues very often and they finally found a battery and a logic board problem about three months before my warranty expiration? i mean, i have not trusted the advice i get which is a complete 180 degrees from when i was first on mac before i had to move to PC and i am wondering if there may be a reason why they did not want to simply go ahead and do the key replacement for me under warranty. it seems really sort of mean and cheap to turn me away on this at the 11th hour with some kind of verbal assurance when i've never been happy with the machine or the explanations on the problems with the machine anyway.
is there some kind of magic words to get them to just replace all the keys so i won't have this as an ADDED problem to my battery life, beachball hangs, sleep battery drain, etc, etc, etc?
THANKSWhat Bob is saying is that according to the table there are different versions of Bootcamp which can be run on each Mac which load the various drivers for the specific versions on Windows.
Windows 8 is designed to run 64bit but it will run 32bit as well it just means you dont get all the benefits and can loose Disc & Ram, but the host mac needs a 64bit compatible processor and it needs to meet the spec for the version of Windows being run and you need the various drivers.
Often this level of support and development wont be provided on older machines as they knnow it will run into problems at some point.
That doesnt mean you cant or shouldnt go for it, as long as you accept it may not be a stright forward install
This thread should provide all the info you need as the user has done what you are looking to do:
https://discussions.apple.com/thread/4897066?tstart=0 -
I have a mid 2009 13'' MBP. I got the battery replaced in Apple store, It then stopped displaying the battery status LED.
After some months of use my MBP died outside USA. I got it checked in Apple verfied Service centre and was told that logic board was faulty.
After I came back to US I took my MBP to Apple store and was told that there is liquid damage in the system. My question is that if there was liquid damage why did my MBP stop displaying the battery status right after the battery was changed secondly why didnt the apple verified Service centre tell me that there was liquid damage afterall I paid them the money for diagnosing the problem.
Is there a process i can followup on this problemThese are question you would need to ask that service center.
This is a User to User forum. No Apple employees here. -
I have a mid 2009 Macbook Pro and i know the Mini-display port does not support audio out but does it support HDMI out? or do i have to buy a Mini-display to DVI and then a DVI to HDMI adapters?
Run MDP to HDMI for picture. Use a cable like this to run sound from your audio out on your Mac to your TV's audio in. That's about all you can do.
-
I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either it says that i have a newer bootcamp version. I tried a few tricks but they didnot work. I hope to be helped
Welcome to Apple Support Communities
You can install a 64-bit Windows 7 or Vista version in your Mac. Make sure you downloaded these drivers > http://support.apple.com/kb/DL1630 Also, if you have the Snow Leopard DVD you used to upgrade your Mac or the OS X DVD that came with your Mac, you can use it to install the Boot Camp drivers -
Have macbook mid 2009, with leopard, updated to yosemite, while erasing partition erased hd, dot have backups, powerup shows folder with question mark, inserting grey dvd shows apple and spinning wheel, please help
Clean Install of Snow Leopard
1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
with your computer. Insert the disc into the optical drive and restart the computer.
After the chime press and hold down the "C" key. Release the key when you see
a small spinning gear appear below the dark gray Apple logo.
2. After the installer loads select your language and click on the Continue
button. When the menu bar appears select Disk Utility from the Utilities menu.
After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
size.) Click on the Partition tab in the DU main window. Set the number of
partitions to one (1) from the Partitions drop down menu, click on Options button
and select GUID, click on OK, then set the format type to MacOS Extended
(Journaled, if supported), then click on the Apply button.
3. When the formatting has completed quit DU and return to the installer. Proceed
with the OS X installation and follow the directions included with the installer.
4. When the installation has completed your computer will Restart into the Setup
Assistant. Be sure you configure your initial admin account with the exact same
username and password that you used on your old drive. After you finish Setup
Assistant will complete the installation after which you will be running a fresh
install of OS X. You can now begin the update process by opening Software
Update and installing all recommended updates to bring your installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1. From here you can upgrade to Yosemite by re-downloading it from the Purchases page in the App Store. -
At the moment i'm using my macbook pro with an ethernet cable = where i'm now i don't have wi-fi -> now i'm trying to do a wi-fi hotspot for my iphone through my macbook pro, but it's doesn't work - please help me!
Theres almost a trick to it for first time users, goto SETTINGS...General......Cellular (if Verizon) ....Personal Hotspot, turn it on.....turn on wifi on your Mac, select your Iphone. Enter password.
If you take too long doing it, youll need turn turn off and on real quick the "personal hotspot" slider on the Phone.......then go quick again thur the Mac. -
I have not used my CS3 version for about 3-4 years. I tried to use it recently and I get a message about activation. Called the phone number recommended but no longer in use. How do I start using MY version I paid for? Using PC
Can you activate CS3. If you lost your serial you can retrieve it from Adobe.com. Sign in at Adobe.com the use this link https://www.adobe.com/account/my-products-services.html When your Adobe Product list is displayed click on your CS3 product your serial number should be displayed.
-
f i have a mid 2009 mac book pro and an apple tv that is the latest one. i can not mirror the mac book on my tv. is it the fact that my computer is a little older than 2011 models which will work. any info is greatly appreciated
chuck schickYes. You need 2011 or later in order to mirror as it requires the newer processor. The alternative is airparrot, which does it via software.
Maybe you are looking for
-
I have a black Macbook running 10.5.8. A while ago iPhoto stopped opening. Time Machine also stopped working properly- it would back up for about 10 gB and then would stop. Photobooth also then began to stop working correctly; it would make my finder
-
SQL to FILE interface with column headers
Hi All, I have designed an interface to extract the data from Oracle to flat file (.txt file ) . 1) I am getting the column headers in the output file(. txt file) but I don't want to see any column headers 2) While creating the data source in data Mo
-
I am trying to display pics from Macbook to TV. The pics are now in iPhoto. I understand we should be able to use "home sharing" in iTunes to display them on TV thru an Apple TV but we can't seem to get the pics into iTunes from iPhoto. Any sugges
-
Hi all, I am an abapper. I would like to shift to a new technology, I do not know Java, got some 2 yrs experience in ABAP. I would like to learn either EP, XI, or BI/BW. Please advise me on which would be better for me. Please help me figure out.. Re
-
HTMLLoader and embeded *.pdf file - get some info
Hi, Is there any way to get some info from embeded in HTMLLoader *.pdf file ? I'm writing a small AIR application which need's for example number of a currently viewed pdf page. I'm using Flash Builder (trail version) and Adobe Reader 9 as a pdf brow