I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?
I have a new Macbook pro, I cannot get past the country selection screen. 'Continue' is greyed out and keys just make error sounds. How do I move it on?
sideeque wrote:
I have the same problem. What did you do last time?
What should I do now? Its around 40 miles away the apple store? Would they pay my taxi fare to go and return?
How can we trust this apple product?
You are still under warranty. Call Apple Care.
Similar Messages
-
New MacBook Pro, unable to get past the select your country screen during initial setup.
I purchased a new MacBook Pro last night and am unable to get past the initial setup screen where you select your country. The mouse will move around, but won't actually allow me to click on 'continue'. I've also tried the keyboard commands to move to the next screen. Nothing...
I just experienced this, and I am recording the solution here for posterity. I got through the setup using the keyboard (tab to move between controls and space to select), thinking that the mouse click would work when I got through it. But I was dismayed to find that it did not ...
... at least so I thought! But actually, you have to push down the mouse pad, NOT just tap it. You can turn on tap-to-click later, but at the start you must push it until it audibly clicks. It is not obvious if you are used to Windows laptop mouse pads like me, where tap-to-click is the ubiquitous norm. -
Hi! I've got CS3 Design Standard - the actual disks and Software License certificate. It was installed on my laptop which crashed and could therefore not be uninstalled. I have now installed it on my new MacBook Pro, but cannot get it registered with the serial number. Is it because it wasn't uninstalled on the previous laptop? What to do now?? Thx!
Maybe this can help someone else... I simply had to properly uninstall CS3 and reinstall it again after that. I think that sorted it! I also remember having a similar issue with Macs at work a couple of years back. Not sure whether the same applies to CS5/CS6. Here's a link on how to properly uninstall CS3 on Windows XP, Windows Vista and Mac OS. I'm on OS X 10.9.2 but it worked just fine. Remove Creative Suite 3 and CS3 products
-
My macbook pro will not get past the gray screen with the apple logo and a loading bar.
My macbook pro will not get past the grey screen with the apple logo after attempting to load for hours. I have already tried resetting the NVRAM/PRAM and a couple other tricks and no luck. Anyone out there have suggestions for my problem? Help would be much appreciated since i use my computer for everything at school and i am in desperate need to get this baby working again.
You didn't say which OS in your tag, but maybe you might find something here.
http://support.apple.com/kb/TS2570
http://support.apple.com/kb/PH4191
http://support.apple.com/kb/PH7213
http://support.apple.com/kb/HT4125
http://support.apple.com/kb/HT2213 -
my macbook air won't get past the white apple screen. I've tried power cycling the batter but won't help
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
I have a brand new MacBook Pro . I got into voice over and then figured out how to stop that but now have a black box in the middle of the home screen and that box has a bunch of icons .....(Keyboard, pointer etc) I cannot get it to close and I'm not able to go past the home screen. Help
If you click on that window, the menu bar should change to whatever program that is. Then click the program name and click Exit.
If that doesn't work, click the Apple icon, then Force Quit. Look for something that says Not Responding and quit it.
Last... if nothing else works reboot and see if that does it. -
MacBook Pro won't get past the flashing grey file screen?
Ok, so tonight I try turning my MacBook on as normal, it then froze and I saw the rotating umbrella appear. So I restarted it. When trying to turn back on, the system did not load, instead a flashing grey file shape came up with a question mark inside. I have tried restarting with a number of key combinations, Option; option, ALT, P, R. Everything, yet it's not getting past this screen. Whenever I try to do an Internet recovery, it just stays on the wifi selection screen and I select mine, enter the password and then it just goes back onto the selection screen. Nothing is work yet! Incredibly annoyed as it has so much stuff, photos, music everything. I don't even know how I reinstall software as it's stuck... Can someone please help? My software is 10.7 I believe.
Hi PHXSuns,
If you are seeing a flashing question mark on startup, you may find the following article helpful:
Apple Support: A flashing question mark appears when you start your Mac
https://support.apple.com/kb/TS1440
Regards,
- Brenden -
Macbook Pro unable to get pass the Log in Screen.
Hey hope someone can help.
Okay so last night I was using Windows, I shut down, then a few hours later I switched it on to go onto my Mac, but it took forever, I left it though and eventually I got to the log in screen, I entered my password and it was loading then the screen went blue/gray (not sure I think both) and went back into the log in screen again... I did this numerous times before giving up and shutting down. Went to sleep, woke up and resumed this...so I decided to see if I could log into my windows, which it did just fine, I'm on windows typing this right now.
I have run the apple hardware test, extended too, and I have recieved the error code: 4SNS/1/40000000:Th2H-63.000 (No idea what that is)
I have also tried booting from my start up disk that came with my Mac. It gives me the Apple logo on the gray screen then ejects my disc, gives me this long story... kind of goes: panic (cpu 0 caller 0x00431da3):"unable to blah blah... Tells me to restart or shutdown.
I looked at my disc and I think its cracked, So I have to get that replaced.
I think I have to archive and install, I really don't want to lose my music, as I haven't backed it up. 400 songs or so nothing much, I'm not worried about the other stuff as that is all backed up.
Long story short can someone tell me what's going on with my Mac? why am I still able to use windows fine? Has windows done a hit on Mac OS? lol. Is the solution to replace my install disc at Apple? I really don't know, any help would be greatly appreciated thanks, I'm just too tired and can't Google anymore :P
(I have a small partion of 32GB dedicated to Windows Vista.)"I have run the apple hardware test, extended too, and I have recieved the error code: 4SNS/1/40000000:Th2H-63.000 (No idea what that is)"
Neither do I. Suggest that you take your MBP to an Apple Store or an AASP.
"Is the solution to replace my install disc at Apple?"
Yes. You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support for a nominal S&H fee. *You'll need to have the model and/or serial number of your Mac available.*
Since you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number. Here's a list of links to all of those -
http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html
!http://i50.tinypic.com/izvwo1.gif! -
Brand new MacBook Pro doesn't get past grey screen (with spinning gear)
Hello,
I'm a new Apple customer - I bought a new 15" MacBook Pro during the Black Friday sale last week. Since purchase, I've installed the software I needed (Office, CS4) and have used it to browse the web and write emails.
Today when I tried to use it, I simply got to the grey screen with the Apple logo on it and the spinning gear device underneath - got absolutely no further.
I have done the following (running from mains adaptor - but the battery indicator is reporting 7 lights anyhow):
1. Boot from the OSX Install Disc, and run the disc repair utility. It reported no problems found. Restarted... same problem.
2. Boot holding down SHIFT to go into safe mode. Underneath the spinning gears, a progress bar filled up to 100% and then disappeared; leaving the grey screen, logo, and spinning gears. Nothing further.
3. Boot holding Option, P, R as per the manual to reset the PRAM. According to the manual there should have been a chime/beep - there wasn't. It just sits on the grey screen, logo, spinning gears. Nothing further.
Right now I've got a £1300 MacBook Pro less than a week old and it appears to have just packed up.
Am I missing anything here, or should I just return it?
Thanks,
ChrisDefinitely take it back!
My friend bought a new iMac from the Regents St. store a few weeks ago, just before the update to the new models came out, and after a week she couldn't get it to boot. I felt very embarrassed as I had persuaded to her to switch to Mac after years of PC woes, so a broken mac after a week didn't look do me any favours. The genius guys didn't mess around, they took back the dead one and gave her a new one, this time she got the new version, they also threw in iWork free as a good will gesture. New one is running fine.
If you haven't already got Applecare, I highly recommend buying it within the next 12 months. I have needed it on a couple of occasions after the standard warranty ran out and the tech support has been brilliant, got me working again no quibbles. -
New macbook pro, can't get past country selection in set up.
What am I missing? I'm new to using Apple laptops. Just out of the box, I plugged it in and when I get to the "Welcome" screen it asks what country... I select US and hit enter/return and get a tone. The arrow buttons do not allow me to do anything either.
Same here... Anyone else having the same problem, use zimzo2's instructions: (use TAB key to cycle through the options then SPACE key to select and get past that screen)
The "return/enter" key and trackpad tapping didn't work for me either. Thanks for posting the solution here.
Update: Just realized that I was tapping and double tapping the MBP trackpad when you need to use the lower-corner of the pad to click. (I'm used to the separate trackpad that accepts tapping anwhere... whoops.) -
MacBook Pro won't get past the apple screen on startup
The laptop won't startup. I get to the Apple logo and a spinning gear. I've tried starting it 3 times with the same result.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use either of the techniques in Steps 1b and 1c to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 10
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 11
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 12
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
Happy Thanksgiving. Any ideas on how to sync up a brand new man mini with a wireless keyboard. My attempts at following the directions have been frustated so far. Entering the numerical code has not yet led to a successful sync up.
Alright, very good.
Have you tried a PRAM reset? OS X Mavericks: Reset your computer’s PRAM -
I cannot get past the Language selection setup.
I cant scroll up or down through the languages, but apparently i can reset the ipod by holding the middle button and the menu button. So i am confused on why i cant even click the middle button to choose English.
If none of the 5 R's are able to resolve the issue, it's likely a hardware issue, meaning you'll need to have the iPod serviced/replaced either by Apple or a third party service. The clickwheel needs replacing.
http://www.apple.com/support/ipod/five_rs
It might help to let the iPod's battery fully drain first and then charge it back up as well before and after working through each of the 5 Rs.
B-rock -
I have a new MacBook Pro with OS10.8.2 and cannot get Contacts to print a list of addresses with pictures showing. There is a check box selecting "picture" which has been checked - but no picture. This worked fine on OS10.7.5. Problem??
First, back up all data immediately, as your boot drive might be failing.
There are a few other possible causes of generalized slow performance that you can rule out easily.
Reset the System Management Controller.
If you have many image or video files on the Desktop with preview icons, move them to another folder.
If applicable, uncheck all boxes in the iCloud preference pane.
Disconnect all non-essential wired peripherals and remove aftermarket expansion cards, if any.
Check your keychains in Keychain Access for excessively duplicated items.
If you have more than one user account, you must be logged in as an administrator to carry out this step.
Launch the Console application in the same way you launched Activity Monitor. Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Select the 50 or so most recent entries in the log. Copy them to the Clipboard (command-C). Paste into a reply to this message (command-V). You're looking for entries at the end of the log, not at the beginning.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some personal information, such as your name, may appear in the log. Anonymize before posting. That should be easy to do if your extract is not too long. -
I have a new Macbook pro. I can't sign onto facetime, keep getting a message saying my wifi isn't working, but it is. Any suggestions?
Troubleshooting FaceTime
http://support.apple.com/kb/TS3367
Maybe you are looking for
-
Emojis stopped work on ipad air calendar?
I used to be able to use little emoji icons in my calendar on my iPad air without any problem... but recently if I try to add one, it shows up on the event for about 2 seconds then disappears. what could be causing this? Has this ever happened to any
-
Date Dimension processing error
Hi I am currently attempting to apply attribute relationships and a Hierarchy to my date dimension. Please see images 1 and 2 attached. The error that is being displayed is Errors in the OLAP storage engine: A duplicate attribute key has been found
-
Whenever I use the video facility on Skype, my macbook pro crashes. How can it be resolved.
-
Function REUSE_ALV_GRID_DISPLAY
Hi ! I wanted to ask few questions concern a standard sap ALV report created by the function REUSE_ALV_GRID_DISPLAY : 1. How to make columns editable, and to enable the user to change values of the columns ? 2. How to make drop down list to a column
-
HELP NEWBIE Integrating CR into Visual Basic 2010 pro
I am creating reports in CR for ms visual studio(VB) how do I do this I am lost. I do not understand how to have a menu written in vb. A menu with reports that a user can select which report to run. I have been tring to do this for weeks. I am using