I have a pavilion dv4 and my internal microphone is not working. how do i fix this. thanks
I have a pavilion dv4 and the internal microphone is not working. I believe I had it working for 1 time but can;t figure it out. please help. thanks
Hi,
Please check it using these steps:
1. Right click the iocon speaker (bootom right hand side)
2. Select "Recording Devices"
3. Enable the microphone
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Similar Messages
-
I have a 9300 and the track ball is not working how do i fix this?
I have a 9300 and the trackball is not working how do I fix this?
Hi THL1234
Welcome to Support Forums
You can try this KB and see if that helps in resolving your problem.If that fails then you may have to replace your Trackball :
KB29640 : Trackpad ,trackball, or keyboard not working on a BlackBerry Smartphone.
Prince
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it.
Click " Like " if you want to Thank someone.
If Problem Resolves mark the post(s) as " Solution ", so that other can make use of it. -
Hey my lock screen button and home button jammed it doesnt work.How can I fix this problem.But first of all I live in Turkey.But my Iphone 4 is bought from apple store victoria gardens CA.Do I have warranty in Turkey ?
The warranty is only good in the country of purchase.
-
When starting Final Cut Pro 7.0.3 I am all of a sudden getting a message that says "One or more of the scratch disks don't have read/ write access" and now the app won't operate - how do I fix this so I can use Final Cut Pro?
Glad you found the answer. But something seems wrong. FCP should be able to assign the scratch disk to your startup drive. It's not advisable, but it should be possible. You might want to try and figure out what's going on before what ever's going on cause other problems.
-
speaker on phone calls will not work, how can I fix this? I have already done system restart and reset to manufature default. I also have no voice with Safari or any other apps including music!
If your speaker is broken, then you may need to get a repair done.
Are you unable to hear anything at all, or is it just one speaker in particular?
If it is just one speaker, where's it located? -
I have the iphone 5 and my lock button does not work. Can apple fix it or give me a new one. Can they still give me a new one even if I didn't buy my iphone 5 from them I bought it from verizon
Alread asked and answered in your previous post - please do not post the same thing multiple times in multiple forums.
https://discussions.apple.com/thread/5164919 -
I updated to java 7 and now my yahoo games will not work, how do i fix this?
i updated to java 7 and now my yahoo games will not work, how do I fix this?
kathieaross,
click on the Java pane in System Preferences. When the Java Control Panel window opens, click on the Security tab, and set your Security Level to Medium — that will allow “untrusted” applications (i.e. those without certificates from a trusted authority) to run. Press the Apply button in the lower-right corner to confirm the change, then press the OK button to close the window.
Apparently your Yahoo! card games don’t have certificates associated with them, which is why the default security setting of Java SE 7 Update 51 didn’t allow them to run. -
Trying to download Lightroom onto a new iMAC and my serial code isn't working - how do I fix this?
What does "isn't working" actually mean? Any error message?
-
phone is frozen in a middle of a call and my top restart button do not work, how can i fix it
Bummer.
Without having the top button, you couldn't do a hard reset.
I'd say you might be looking at backing up and restoring through iTunes unfortunatley. -
i have my imessage turned on and have full WiFi signal and my imessage still wont work. how do i fiz this problem?
Start here:
http://support.apple.com/kb/ts2755 -
So my iPod touch deleted its main camera and If I try to download another camera app it won't work and it will say that my davice does not support camera apps how do I fix this?
Try resetting your Home screen layout...
Settings / General / Reset / Reset Home Screen Layout
See if it shows up. -
Installed FF4 and now my TouchPad no loner works, how do I fix this?
I installed FF 4 on my Lenovo ThinkPad T61 and now my TouchPad & TouchPoint cannot be used to scroll web pages (they do however work on other programs). I installed the latest driver for the TouchPad & TouchPoint but it did not fix the problem. I also restarted FF in safe mode with Add-on disabled and this did not help either. I can scroll using the arrow key or with the curser, but it's VERY annoying not being able to use the TouchPad & TouchPoint. How can I fix this?
Confirm that you have the latest drivers for the Spyder, 4.5.6. The release notes state that earlier releases had a problem with color cast on some systems. Then run the calibration again. If you continue to have problems, you may want to take this issue up with Datacolor technical support; it's possible that your calibrator is defective, or they may have tips.
Regards. -
I have calibrated with spyder4elite and now my blacks are tinted red, how do I fix this?
I have been using spyder4elite to calibrate my iMac monitor and until now the black and whites have been fine, but now my blacks are tinted red. Does anyone know what I might have done wrong? I recently purged my cache - could that have changed something? How can I fix it now?
Thanks in advance if anyone can help me.
JanoConfirm that you have the latest drivers for the Spyder, 4.5.6. The release notes state that earlier releases had a problem with color cast on some systems. Then run the calibration again. If you continue to have problems, you may want to take this issue up with Datacolor technical support; it's possible that your calibrator is defective, or they may have tips.
Regards. -
<blockquote>Locking duplicate thread.<br>
Please continue here: [[/questions/919962]]</blockquote>
I have a program called commission killer that I have downloaded and I can't open it because it says compileBot has stopped working. It then tells me to either close the program or have Windows look for a solution and then it closes without any solution. I want to be able to use this program and yet I don't know what to do to correct this. I have deleted it closed the firewall and the security program AVG but that didn't work either when I redownloaded the program. Any suggestions>?you need a newer version of pages to open this document
-
My Norton tool bar No longer is visable and does not work, how can I fix this
My Norton 360 that saves all my passwords for me does not work on fire fox 4.0. How can I go back to the previous version? I was not given a warning that Norton 360 wouldn't work until after I had already down loaded 4.0, or I would not have downloaded it!
I did not know that the tool bar was going to disappear!Norton says they are going to update 360 in April for the Firefox 4.0.
You can get Firefox 3.6.16 here: <br />
http://www.mozilla.com/en-US/firefox/all-older.html
http://support.mozilla.com/en-US/kb/Installing+a+previous+version+of+Firefox
Maybe you are looking for
-
I can not open a crw image in photoshop camera Raw.
When I go to open a CRW Image in CS5,Bridge It will not open.It says Could not complite your request because it is not the right kind of document.Need help bad. PS How do I tell what version of Camera Raw I have.By the way I have a Canon EOS 10D came
-
Options to monitor a PC without using SCOM?
How can I monitor a scheduled job on a PC without using SCOM. We have a request to monitor some scheduled jobs on some PCs, but we don't want to use SCOM to monitor individual PCs. Can I use PowerShell or anything else to accomplish this task? Thanks
-
Unbalance transaction Error - Journal Entry Posting
Hi all, Good afternoon. i posted journal entry using DI -API. I have two Journal Entry when i add the first journal Entry added the second journal entry not added its show the Error Unbalanced transaction Each Journal Entry have 2 lines I am using
-
How do I reverse an auto update? mainly a java update
On 6/13/12 there were a few "automatic" updates - one of them was a JAVA for MAC OS X 10.6 update 9 (updating Java SE;6 to 1.6.0_33) Ever since this was installed - I can no longer access a site that has worked for some time now. It is a USCG Aux
-
I would like to generate arbitrarily deeply nested XML documents by some declarative mechanism. I've looked at SQL/XML for the first time today, and in particular the XMLAgg function. Whereas I can use this for one level of group-by and hence one lev