I have a problem, am i going to lose all my files ?
Hello,
I have a lot of pictures on my Ipod. But since i'm coming back from holidays, my ipod doesn't work anymore ! I still can use it and listen to music, but when i plug it, windows ask me to format it, and itunes doesn't recognize it...
I wanted to use iPod updater for updating the firmware without deleting the files, but... iPod updater can't "update", and cn only "restore"... i can't also see the name of the ipod (i have a n/d), and i can't see neither the capacity. I can only see the firmware version, and serial number. But everything about storage seems like dead.
I don't understand why, all my files should be always on it, because i can still listen to all the songs...
My files are important because it's lot of photos of my travels, and i didn't put them on another storage device so... i really don't want to loose them, i must avoid to use the "restore" function.
Is there a way ?
Thank you !
I can't access the ipod through Windows. As i said before, doesn't work anymore !
Getright ? But Getright seems to be a download application, not a recovery program... and i don't think the Ipod need to be recovered, because i'm still able to listen to music on it, but i can't manage it using Windows neither Itunes. Seems to be a problem on the "link" (software link?) between the ipod harddisk and the computer...
Similar Messages
-
I have one problem with Data Guard. My archive log files are not applied.
I have one problem with Data Guard. My archive log files are not applied. However I have received all archive log files to my physical Standby db
I have created a Physical Standby database on Oracle 10gR2 (Windows XP professional). Primary database is on another computer.
In Enterprise Manager on Primary database it looks ok. I get the following message Data Guard status Normal
But as I wrote above the archive log files are not applied
After I created the Physical Standby database, I have also done:
1. I connected to the Physical Standby database instance.
CONNECT SYS/SYS@luda AS SYSDBA
2. I started the Oracle instance at the Physical Standby database without mounting the database.
STARTUP NOMOUNT PFILE=C:\oracle\product\10.2.0\db_1\database\initluda.ora
3. I mounted the Physical Standby database:
ALTER DATABASE MOUNT STANDBY DATABASE
4. I started redo apply on Physical Standby database
alter database recover managed standby database disconnect from session
5. I switched the log files on Physical Standby database
alter system switch logfile
6. I verified the redo data was received and archived on Physical Standby database
select sequence#, first_time, next_time from v$archived_log order by sequence#
SEQUENCE# FIRST_TIME NEXT_TIME
3 2006-06-27 2006-06-27
4 2006-06-27 2006-06-27
5 2006-06-27 2006-06-27
6 2006-06-27 2006-06-27
7 2006-06-27 2006-06-27
8 2006-06-27 2006-06-27
7. I verified the archived redo log files were applied on Physical Standby database
select sequence#,applied from v$archived_log;
SEQUENCE# APP
4 NO
3 NO
5 NO
6 NO
7 NO
8 NO
8. on Physical Standby database
select * from v$archive_gap;
No rows
9. on Physical Standby database
SELECT MESSAGE FROM V$DATAGUARD_STATUS;
MESSAGE
ARC0: Archival started
ARC1: Archival started
ARC2: Archival started
ARC3: Archival started
ARC4: Archival started
ARC5: Archival started
ARC6: Archival started
ARC7: Archival started
ARC8: Archival started
ARC9: Archival started
ARCa: Archival started
ARCb: Archival started
ARCc: Archival started
ARCd: Archival started
ARCe: Archival started
ARCf: Archival started
ARCg: Archival started
ARCh: Archival started
ARCi: Archival started
ARCj: Archival started
ARCk: Archival started
ARCl: Archival started
ARCm: Archival started
ARCn: Archival started
ARCo: Archival started
ARCp: Archival started
ARCq: Archival started
ARCr: Archival started
ARCs: Archival started
ARCt: Archival started
ARC0: Becoming the 'no FAL' ARCH
ARC0: Becoming the 'no SRL' ARCH
ARC1: Becoming the heartbeat ARCH
Attempt to start background Managed Standby Recovery process
MRP0: Background Managed Standby Recovery process started
Managed Standby Recovery not using Real Time Apply
MRP0: Background Media Recovery terminated with error 1110
MRP0: Background Media Recovery process shutdown
Redo Shipping Client Connected as PUBLIC
-- Connected User is Valid
RFS[1]: Assigned to RFS process 2148
RFS[1]: Identified database type as 'physical standby'
Redo Shipping Client Connected as PUBLIC
-- Connected User is Valid
RFS[2]: Assigned to RFS process 2384
RFS[2]: Identified database type as 'physical standby'
Redo Shipping Client Connected as PUBLIC
-- Connected User is Valid
RFS[3]: Assigned to RFS process 3188
RFS[3]: Identified database type as 'physical standby'
Primary database is in MAXIMUM PERFORMANCE mode
Primary database is in MAXIMUM PERFORMANCE mode
RFS[3]: No standby redo logfiles created
Redo Shipping Client Connected as PUBLIC
-- Connected User is Valid
RFS[4]: Assigned to RFS process 3168
RFS[4]: Identified database type as 'physical standby'
RFS[4]: No standby redo logfiles created
Primary database is in MAXIMUM PERFORMANCE mode
RFS[3]: No standby redo logfiles created
10. on Physical Standby database
SELECT PROCESS, STATUS, THREAD#, SEQUENCE#, BLOCK#, BLOCKS FROM V$MANAGED_STANDBY;
PROCESS STATUS THREAD# SEQUENCE# BLOCK# BLOCKS
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
ARCH CONNECTED 0 0 0 0
RFS IDLE 0 0 0 0
RFS IDLE 0 0 0 0
RFS IDLE 1 9 13664 2
RFS IDLE 0 0 0 0
10) on Primary database:
select message from v$dataguard_status;
MESSAGE
ARC0: Archival started
ARC1: Archival started
ARC2: Archival started
ARC3: Archival started
ARC4: Archival started
ARC5: Archival started
ARC6: Archival started
ARC7: Archival started
ARC8: Archival started
ARC9: Archival started
ARCa: Archival started
ARCb: Archival started
ARCc: Archival started
ARCd: Archival started
ARCe: Archival started
ARCf: Archival started
ARCg: Archival started
ARCh: Archival started
ARCi: Archival started
ARCj: Archival started
ARCk: Archival started
ARCl: Archival started
ARCm: Archival started
ARCn: Archival started
ARCo: Archival started
ARCp: Archival started
ARCq: Archival started
ARCr: Archival started
ARCs: Archival started
ARCt: Archival started
ARCm: Becoming the 'no FAL' ARCH
ARCm: Becoming the 'no SRL' ARCH
ARCd: Becoming the heartbeat ARCH
Error 1034 received logging on to the standby
Error 1034 received logging on to the standby
LGWR: Error 1034 creating archivelog file 'luda'
LNS: Failed to archive log 3 thread 1 sequence 7 (1034)
FAL[server, ARCh]: Error 1034 creating remote archivelog file 'luda'
11)on primary db
select name,sequence#,applied from v$archived_log;
NAME SEQUENCE# APP
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00003_0594204176.001 3 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00004_0594204176.001 4 NO
Luda 4 NO
Luda 3 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00005_0594204176.001 5 NO
Luda 5 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00006_0594204176.001 6 NO
Luda 6 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00007_0594204176.001 7 NO
Luda 7 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\IRINA\ARC00008_0594204176.001 8 NO
Luda 8 NO
12) on standby db
select name,sequence#,applied from v$archived_log;
NAME SEQUENCE# APP
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00004_0594204176.001 4 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00003_0594204176.001 3 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00005_0594204176.001 5 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00006_0594204176.001 6 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00007_0594204176.001 7 NO
C:\ORACLE\PRODUCT\10.2.0\ORADATA\LUDA\ARC00008_0594204176.001 8 NO
13) my init.ora files
On standby db
irina.__db_cache_size=79691776
irina.__java_pool_size=4194304
irina.__large_pool_size=4194304
irina.__shared_pool_size=75497472
irina.__streams_pool_size=0
*.audit_file_dest='C:\oracle\product\10.2.0\admin\luda\adump'
*.background_dump_dest='C:\oracle\product\10.2.0\admin\luda\bdump'
*.compatible='10.2.0.1.0'
*.control_files='C:\oracle\product\10.2.0\oradata\luda\luda.ctl'
*.core_dump_dest='C:\oracle\product\10.2.0\admin\luda\cdump'
*.db_block_size=8192
*.db_domain=''
*.db_file_multiblock_read_count=16
*.db_file_name_convert='luda','irina'
*.db_name='irina'
*.db_unique_name='luda'
*.db_recovery_file_dest='C:\oracle\product\10.2.0\flash_recovery_area'
*.db_recovery_file_dest_size=2147483648
*.dispatchers='(PROTOCOL=TCP) (SERVICE=irinaXDB)'
*.fal_client='luda'
*.fal_server='irina'
*.job_queue_processes=10
*.log_archive_config='DG_CONFIG=(irina,luda)'
*.log_archive_dest_1='LOCATION=C:/oracle/product/10.2.0/oradata/luda/ VALID_FOR=(ALL_LOGFILES, ALL_ROLES) DB_UNIQUE_NAME=luda'
*.log_archive_dest_2='SERVICE=irina LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES, PRIMARY_ROLE) DB_UNIQUE_NAME=irina'
*.log_archive_dest_state_1='ENABLE'
*.log_archive_dest_state_2='ENABLE'
*.log_archive_max_processes=30
*.log_file_name_convert='C:/oracle/product/10.2.0/oradata/irina/','C:/oracle/product/10.2.0/oradata/luda/'
*.open_cursors=300
*.pga_aggregate_target=16777216
*.processes=150
*.remote_login_passwordfile='EXCLUSIVE'
*.sga_target=167772160
*.standby_file_management='AUTO'
*.undo_management='AUTO'
*.undo_tablespace='UNDOTBS1'
*.user_dump_dest='C:\oracle\product\10.2.0\admin\luda\udump'
On primary db
irina.__db_cache_size=79691776
irina.__java_pool_size=4194304
irina.__large_pool_size=4194304
irina.__shared_pool_size=75497472
irina.__streams_pool_size=0
*.audit_file_dest='C:\oracle\product\10.2.0/admin/irina/adump'
*.background_dump_dest='C:\oracle\product\10.2.0/admin/irina/bdump'
*.compatible='10.2.0.1.0'
*.control_files='C:\oracle\product\10.2.0\oradata\irina\control01.ctl','C:\oracle\product\10.2.0\oradata\irina\control02.ctl','C:\oracle\product\10.2.0\oradata\irina\control03.ctl'
*.core_dump_dest='C:\oracle\product\10.2.0/admin/irina/cdump'
*.db_block_size=8192
*.db_domain=''
*.db_file_multiblock_read_count=16
*.db_file_name_convert='luda','irina'
*.db_name='irina'
*.db_recovery_file_dest='C:\oracle\product\10.2.0/flash_recovery_area'
*.db_recovery_file_dest_size=2147483648
*.dispatchers='(PROTOCOL=TCP) (SERVICE=irinaXDB)'
*.fal_client='irina'
*.fal_server='luda'
*.job_queue_processes=10
*.log_archive_config='DG_CONFIG=(irina,luda)'
*.log_archive_dest_1='LOCATION=C:/oracle/product/10.2.0/oradata/irina/ VALID_FOR=(ALL_LOGFILES, ALL_ROLES) DB_UNIQUE_NAME=irina'
*.log_archive_dest_2='SERVICE=luda LGWR ASYNC VALID_FOR=(ONLINE_LOGFILES, PRIMARY_ROLE) DB_UNIQUE_NAME=luda'
*.log_archive_dest_state_1='ENABLE'
*.log_archive_dest_state_2='ENABLE'
*.log_archive_max_processes=30
*.log_file_name_convert='C:/oracle/product/10.2.0/oradata/luda/','C:/oracle/product/10.2.0/oradata/irina/'
*.open_cursors=300
*.pga_aggregate_target=16777216
*.processes=150
*.remote_login_passwordfile='EXCLUSIVE'
*.sga_target=167772160
*.standby_file_management='AUTO'
*.undo_management='AUTO'
*.undo_tablespace='UNDOTBS1'
*.user_dump_dest='C:\oracle\product\10.2.0/admin/irina/udump'
Please help me!!!!Hi,
After several tries my redo logs are applied now. I think in my case it had to do with the tnsnames.ora. At this moment I have both database in both tnsnames.ora files using the SID and not the SERVICE_NAME.
Now I want to use DGMGRL. Adding a configuration and a stand-by database is working fine, but when I try to enable the configuration DGMGRL gives no feedback and it looks like it is hanging. The log, although says that it succeeded.
In another session 'show configuration' results in the following, confirming that the enable succeeded.
DGMGRL> show configuration
Configuration
Name: avhtest
Enabled: YES
Protection Mode: MaxPerformance
Fast-Start Failover: DISABLED
Databases:
avhtest - Primary database
avhtestls53 - Physical standby database
Current status for "avhtest":
Warning: ORA-16610: command 'ENABLE CONFIGURATION' in progress
It there anybody that experienced the same problem and/or knows the solution to this?
With kind regards,
Martin Schaap -
i just plugged my iphone in to download some pix to my computer and my phone is now showing a plug with the itunes icon and its telling me I have to restore my phone and will lose all my data. *** is going on and how can I go back?
"I have logged in to my itunes account on a different computer and none of my purchased music is showing up."
Correct. it does not magially appear in other places. It will only be where you put it.
"I also have plugged my iphone in to get updates but it says I will lose all media and apps if I don't update on the computer where I sync everything. "
Correct as well. Iphone will sync with one computer at a time. Syncing to another will erase the current content.
You need to copy everything ( itunes library/contacts/pics/calendars/files/docs) from the old computer, or your backup copy of the old one, to the new one. -
I have a problem with the mac can not read video files with the extension IMOD. How can I solve this problem?
By doing a Google search.
-
My phone doesn't have any cellular phone functions...but it CAN send text messages and access data. Has this happened to anyone else? I've gone through three Samsung Galaxy S5's in the past three days, the last two have this problem and the first stopped working all together. I've had new sim cards put in, ive done hard resets on the phone, i've rebooted the phone, done battery pulls, and tech support has reset the signal to my phone. Nothing has worked. (I just "upgraded" <- lol.... and my old phone IS turned off.)
Im in 79707. So to recap my whole case: I upgraded my device using the verizon wireless website. I received my phone and switched my old SIM card from my Droid Razr Maxx HD into the new Galaxy S5. Everything worked fine until the next morning (May 31st) when I woke up and the phone wouldn't turn on. I took the phone to the local Verizon store and they were also unable to turn it on. They issued me a new Galaxy S5 (referred to as phone 2) and switched my SIM card into that one.
With PHONE 2 i was able to make calls and receive calls, along with text and data for approximately four hours. After that, i was unable to use the phone function of the device, but text and data were still functioning. I took PHONE 2 back to the Verizon store where they attempted to hard reset the phone twice, they also installed two new SIM cards at the store. After this they would get the same error, which is the phone just reading "Dialing..." after attempting to make a call. The Verizon associate declared the phone "DOA" and issued me another Galaxy S5 (referred to as PHONE 3).
PHONE 3 worked well, with phone text and data featured intact from when I received it on the after noon of the 31st until approximately 2:30PM on June 1st. I contacted Verizon Tech Support via Gmail phone to attempt the correct the problem. They reset the connection, had me do a battery pull, had me close the "phone" application, and erase the data and catche, then restart the phone. All of which had no effect. My phone is still able to receive texts and use data (even with wifi off) it simply cannot make or take phone calls. all it says is "dialing..." when I attempt to make a call. When other phones call my device it rings once on their end and directs them to voicemail, PHONE 3 does not ring on my end.
I have made sure my old phone is completely powered down. -
Hi! I have a problem. My macbook pro install all applications only in german( when i change language, it still install in german) This began from aperture 3, it was installed in german, than all apps.Please help.
Hi! I have a problem. My macbook pro install all applications only in german( when i change language, it still install in german) This began from aperture 3, it was installed in german, than all apps.Please help.
-
Hi ! I have an iPhone 4s , bought it from apple company , I have charging problem , very slowly , it sometimes takes all day of charging , please helpe ...
In most countries they will do so for a fee. US$199 for a 4S. It may just need a new battery, which Apple will install for about US$70.
-
I was having computer problems and dumped my computer and started over from scratch. I had to download itunes to this comptuer again. But now when I go to sync my iPhone with my computer, it appears that I'm going to lose all the information on my iPhone. How can I keep this from happening? I'm not real computer literate so need simple terminology and directions. I've been trying to search for the answer to my question and I've found some answers, but I need more precise directions. Such as: one answer says to sync to the windows contacts and make sure there is at least one contact in your windows contacts so it will merge rather than wipe out your phone. I don't know where windows contacts is to be found so don't know how to add a contact in it. What about the ringtones I have? It wants to wipe them out too, but I don't want to purchase a new ringtone to have in the ringtone area (where ever that is). Anyone who can guide me in simple language would be a blessing.
See Recover your iTunes library from your iPod or iOS device, there are useful links in there even if you don't have a device.
tt2 -
We have a newish apple mac and this morning all our files have vanished - all photo's, vidoes, music etc. How can we get it back? Thanks
First of all, look in the garbage. It's easy to move a folder there without knowing it.
Second, do a Spotlight Search (Cmd-Space), and search for a file you know should be there. If you find the file, there's a good chance that the other files you're looking for are there, too.
If you're in kind of a crisis mode, coming up with pat advice probably isn't a good policy - but I suggest investing in a backup drive in case anything goes wrong. A program like Time Machine can be a life saver.
Post with your results! -
Hi sorry if this a bt of a noob question but ive looked and looked and cant find the answer. Even tho it is probably staring me in the face.
Im wanting to upgrade to 2.0 but its saying that it needs to wipe my touch but as the computer i am using isnt the computer i first used my touch on im going to lose all my songs. When i goto to backup it only seems to backup the music i have added since i started using my new computer!
is this right is there no way i can save all my music???You will lose your older music, yes. You'd need to move it from the iPod into iTunes first. To do that, you need 3rd party software (google for TouchCopy, iPodAccess, iGadget). If you get the music into iTunes before you upgrade to v2.0, you will not lose your music.
Hope this helps... -
My iphone4 isn't updated or synced to icloud because last time I tried it merged with a family members phone. Now I'm getting a new phone am scared I am going to lose all my contacts. Any suggestions on how I am to secure them?
Backup using itunes http://support.apple.com/kb/HT1766
Are you sharing an apple id with someone? that would be the only reason if would merged info. -
had to update phone, screen tells me to go to itunes on my pc, but if I press the recovery am I going to lose all my music
Nothing should be lost... But it is Both Prudent & Recommended to Create and Maintain Backups of Anything you cannot afford to lose.
http://www.apple.com/support/itunes/install/
Also see this User Tip by turingtest2
Troubleshooting issues with iTunes for Windows updates -
i hav iphone and i restart it and delete all the files inside how can i start it again it say i need a valid sim with no pin lock to activate iphone again
ICCID unknown is a critical failure, usually caused by hacking or jailbreaking the phone. It can not be fixed. The phone will need to be replaced.
-
I cannot see my Hotmail saved messages onmy iPad 4. I do not have this problem on my iPad 2. The settings appear identical.Any suggestions to cure the problem? Thank you.
My iPad 2 does exactly the same thing. But I just have to go on to my wifi options and you can either forget this network and then press it again or you can turn wifi off and on again and press that wifi.
Kind regards, -
I currently have Mavericks but my original OS X disk that I have I'm pretty sure is Mac OS X 10.6.6. I'm not great with computers but am usually able to fix problems I have had with mine in the past. I have reinstalled and reset my computer to factory settings before, but I am locked out of my computer completely & can't get to my files to save them & I really dont want to lose them. I was in Safari earlier opening a file, the page started to not respond & froze up my whole desktop so I did a hard shutdown & restarted my computer. I haven't been able to get back into my account ever since. If my only choice is to lose my files & reinstall everything, I need detailed instructions because I actually attempted to do this at first, out of desperation to fix my computer & the installer was asking me to select what disk I wanted to reinstall lion to yet I dont have a disk for that nor do I know what it exactly is asking of me? Please help
Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark or globe appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Maybe you are looking for
-
Lenovo T430 unable to print to Officejet 8625 overwireless
After trying each and every method to resolve this myself without success, reaching out to the forums. My Lenovo T430 ThinkPad is on a wireless network which my printer is on. The printer is detected by the HP Doctor software. However, no matter wha
-
Options for NAS sharing in a large environment
The lack of Samba on Lion is a major problem for me at work and my employer. I work for a large university. We have one of the largest computer labs in the country, loaded with iMacs and MacPros. Without being able to mount cifs file shares on our NA
-
Does anyone know which table the standard SAP extractor: FI_AP_04 pulls from (other than BSIK and BSAK)? Thanks!
-
Hi, How i can maintain Field status varient for a company code. Thanks, Rajendra.
-
Hi ! We have been burgled and my Macbook has been stolen All my data and pictures were on it. Do you know if Apple could locate it by any way ? As soon as it will be connected to the Internet it should try to look for updates, Apple should be able to