I have a problem with my VGA output.

I bought a VGA adaptor, plugged it into my ipad (3rd gen running iOS 6) and used a VGA cable to connect my iPad to a TV with a VGA input. I get no image, no mirroring, no slideshows (using keynote) nothing. I have tried looking around but can only find information relating to iPad 2 and older versions of the operating system. Any tips before I declare my VGA adaptor as a possible faulty buy?
I have tried:
1. Turning off my iPad and then plugging the VGA adaptor into the bottom of the iPad. The iPad automatically turned on but still nothing.
2. Turning off and on.
3. Looking through the settings but there is nothing to see.
4. Messing about with the settings on the TV
5. shouting!
6. it does not seem to matter which apps i use. However, interestingly..... When the VGA adaptor was plugged into the iPad, I used keynotes and pressed the play button, it went into presentation mode like you would expect when using an external monitor but, no picture on the TV.
Thanks

No worries all sorted!
It turns out that it was the AVG adaptor that was faulty. Now I have replaced it the iPad popped up on the monitor right away.

Similar Messages

Both xp and windows 7 have video problems with my VGA connection using TV

both xp and windows 7 have video problems with my VGA connection using TV as my monitor when it gets to starting up windows no matter what version it will not I have let my mac on all night and still says starting windows or the windows 7 logo and nothing else will happen also when I use a 3rd patty software like peraills or other it works like a charm how to fix it?

To map the drive on your computer click on Start - RUN - type "\\192.168.1.1" and click ok... When prompted for Username and Password type "admin" and click ok... Now you will be able to see the folder which you have shared on your router, right click on it and select "Map network drive" and click on finish.
Now it will map the drive on your computer and you should be able to transfer the file from your computer to the USB drive.

Equium P200-1ED - have problem with installing VGA driver

Hello
I have problem with installing vga video driver, each time in installion it stops on
Version: 6,14.10,4833 and there is error poping up.........
Please help!

Hello
What error message is it exactly?
Make sure that the chipset driver and SP2 is installed at least.
I had a similar issue that I cant install the display driver. The error message was something like the hardware is not supported
But it was very easy to solve this problem. I installed the driver via device manager. I have selected the graphic card and choose update driver. Then I did choose the advanced installation to choose the directory by myself.
Anyway, after restart the driver was installed and it worked. :)
Greets

Anyone have a problem with the HDMI port suddenly not recognizing any digital source imput signal?

I have an HP 2711x monitor.
Anyone suddenly have a problem with it no longer recognizing any digital source input with the HDMI port (or DVI), yet the VGA port works fine?
Thanks.

Hello Largelee,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand you are having issues with your HP 2711x Monitor not displaying HDMI or DVI inputs, yet it can display VGA inputs. Are these inputs all coming from the same device? Such as your computer? Does the computer's outputs show up on other devices via HDMI and DVI? If it works are you using the same cables? Are there any messages displayed on the monitors screen when you have the HDMI or DVI hooked up?
Check to see if any of the documents below pertaining to the HP 2711x Monitor pertain to your issue:
Flat Panel Monitor Displays Message about No Signal, Signal out of Range, Sleep, or Power Save
'Input out of Range' Error After a Recovery or Upgrading to Windows 7
Monitor is Blank
Please respond with the answers to these questions so I can further assist you. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Since installing mountain lion i have a problem with mail. when i delete a message close and open mail the message has come back. please help!

Since installing Mountain Lion i have a problem with Mail. I delete a number of messages from the same person but keep the newest message in my Inbox. I actually delete them from the Trash. The next time i open Mail the deleted messages are back again. Can anybody please help as this is getting annoying. Thanks in Anticipation.

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore will not, in itself, solve your problem.
First, empty the Trash.
Triple-click the line below to select it, then copy the selected text to the Clipboard (command-C):
find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 -o -acl $ 2> /dev/null | wc -l
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
The output of this command, on a line directly below what you entered, will be a number such as "41." Please post it in a reply.

Hello. I have a problem with OEL 6.5 and ocfs2. When I mount ocfs2 with mount -a command all ocfs2 partitions mount and work, but when I reboot no ocfs2 partitions auto mount. No error messages in log. I use DAS FC and iSCSI FC.

Hello.
I have a problem with OEL 6.5 and ocfs2.
When I mount ocfs2 with mount -a command all ocfs2 partitions mount and work, but when I reboot no ocfs2 partitions auto mount. No error messages in log. I use DAS FC and iSCSI FC.
fstab:
UUID=32130a0b-2e15-4067-9e65-62b7b3e53c72 /some/4 ocfs2 _netdev,defaults 0 0
#UUID=af522894-c51e-45d6-bce8-c0206322d7ab /some/9 ocfs2 _netdev,defaults 0 0
UUID=1126b3d2-09aa-4be0-8826-0b2a590ab995 /some/3 ocfs2 _netdev,defaults 0 0
#UUID=9ea9113d-edcf-47ca-9c64-c0d4e18149c1 /some/8 ocfs2 _netdev,defaults 0 0
UUID=a368f830-0808-4832-b294-d2d1bf909813 /some/5 ocfs2 _netdev,defaults 0 0
UUID=ee816860-5a95-493c-8559-9d528e557a6d /some/6 ocfs2 _netdev,defaults 0 0
UUID=3f87634f-7dbf-46ba-a84c-e8606b40acfe /some/7 ocfs2 _netdev,defaults 0 0
UUID=5def16d7-1f58-4691-9d46-f3fa72b74890 /some/1 ocfs2 _netdev,defaults 0 0
UUID=0e682b5a-8d75-40d1-8983-fa39dd5a0e54 /some/2 ocfs2 _netdev,defaults 0 0

What is the output of:
# chkconfig --list o2cb
# chkconfig --list ocfs2
# cat /etc/ocfs2/cluster.conf

I have a problem with ALV Grid User Command?

Hi Experts,
I have a problem with ALV GRID User Command.
I am calling TCODE IW33 (Order Display) from the ALV output at first time by selecting an order. But, User command is calling IW33 Initial screen with blank value of order. Even I checked in debugging the value what I selected is passing properly, but once that screen (IW33 Initial) displays, value doesn't appear. Then, Manually, I created another session and gone to TCODE IW33 and displayed an order. After that I came out from that order. Then again run my ALV program and selected another order, now order is displaying, but not what I selected current order instead of displaying previous order what I just displayed manually. If I selected any other order, system will display the same order what I dislayed manually.
Here is my code.
FORM user_command_alv USING u_ucomm TYPE sy-ucomm
                       us_self_field TYPE slis_selfield.
CASE u_ucomm.
WHEN '&IC1'.
READ TABLE it_final INDEX us_self_field-tabindex INTO wa_final.
        WHEN 'ORDER'.
          IF NOT wa_final-order IS INITIAL.
            SET PARAMETER ID 'COK' FIELD wa_final-order.
            CALL TRANSACTION 'IW33' AND SKIP FIRST SCREEN.
          ENDIF.
endform.
PARAMETER ID 'COK' also the standard one.
Could you please help me out, Where I did wrong?
If I select any order, that order only should display.
Thanks in advance.
Regards,
Sarayu.
Code Formatted by: Alvaro Tejada Galindo on Jan 8, 2009 2:33 PM

hi,
Please check it once the Paramater ID is 'ANR' for IW33 order number.
Hope this may help.
Regards,
Sravanthi

HI, I just bought Photoshop CS5 and I have a problem with HDR pro

HI, I just bought Photoshop CS5 and I have a problem with HDR pro . when I am trying to mount 3 images together it act in a strange way ( the images appear and disappear many times) then when the window with the result appear and I say ok it open up in photoshop as a single image ( in the layers there is just 1 photo) and when I am trying to work it up with the Plug in/filter HDR Effex Pro (Nik softwear) a pop up window appear saying that the file is missing and the operation it is not possible. Why and what is happening ? Someone can help me ?

This is normal operation. The output from HDR pro does not produce a layered file. You make all your adjustments in the Nik Plug-in. Once Nik has finished you then make any rinal changes in Photoshop. Trying to use NIK again on the image in Photoshop is not the way to do this.
When HDR pro comes up do you see all the presets and controls? Presets on the left and controls on the right
MK

Hey Guys i have a problem with my mac since last month and it wont boot up it freezes in a grey apple logo and and spinning gear any body know how to fix this?

Hey Guys i have a problem with my mac since last month and it wont boot up it freezes in a grey apple logo and and spinning gear any body know how to fix this?

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
How to use and troubleshoot FireWire target disk mode
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode.* The instructions provided by Apple are as follows:
Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
When you see the gray Apple logo, release the shift key.
If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
*Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
Step 6
Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
Step 7
Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
Step 8
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

[VIA] PROBLEM WITH SIS VGA

I have a problem one sis VGA 32mb agp(s-305) she does not work with ms-6712 mbo it wont even start with the card in the slot?
What is the problem could it be voltage? i upgraded to newest bios so that bios can't be the problem.
Help if you can!!!

Quote from: Wonkanoby on 15-April-05, 18:40:16
IS IT AT LEAST AN AGPX 4 1.5V CARD
newer boards dont work with old agp x 2 3.3v cards
unfortenatly it is an 3,3v card

I have a problem with wifi in my iphone 4s, i already try everything and download latest version 7.1(11D167) but wifi switch is not working, its my humble request to Apple support team that pls resolve this problem as soon as possible because

I have a problem with wifi in my iphone 4s, i already try everything and download latest version 7.1(11D167) but wifi switch is not working, its my humble request to Apple support team that pls resolve this problem as soon as possible because its a prestiage of Apple Company.
Pls inform me how can i resolve the problem of wifi.

You have to go to autherized iPhone agent.

Have a problem with Lightroom 5.4. Since the program crashed yesterday it won't launch, it comes up with the message "Lightroom encountered an error when reading its preview cache and needs to quit". " Lightroom will attempt to fix this problem net ti

Have a problem with Lightroom 5.4. Since the program crashed yesterday it won't launch, it comes up with the message "Lightroom encountered an error when reading its preview cache and needs to quit". " Lightroom will attempt to fix this problem next time it launches". Except that it doesn't, I keep getting the same message and the program closes. Does anyone know what I can do to repair it? Can't back up, can't do anything.

There are dozens of threads in this forum that describe the fix

I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

I have a problem with the sync between iTunes and ipad2. I can not see the files in iPad. Help me please.

Cannot see what files ? Music (synced music should appear in the iPod app), films/TV shows (Videos app), documents ... ?

I have a problem with JDBC Realm in Tomcat/Oracle/Win XP

I have a problem with JDBC Realm in Tomcat.
I have attached my server.xml file located in the
C:\Program Files\Apache Software Foundation\Tomcat 5.5\conf\server.xml
The Problem is that when I login I get the user name and password prompt but it does not resolve.
When I enter in the tomcat-users.xml password with memory realm uncommented it works fine.
C:\Program Files\Apache Software Foundation\Tomcat 5.5\conf\tomcat-users.xml
Is there a cache or something I need to reset for the JDBC Realm to work?
I have attached my tables and contents as well...
Did I miss something????
Thanks
Phil
server.xml
<Server port="8005" shutdown="SHUTDOWN">
<Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" />
<Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" />
<Listener className="org.apache.catalina.storeconfig.StoreConfigLifecycleListener"/>

<GlobalNamingResources>

<Environment name="simpleValue" type="java.lang.Integer" value="30"/>
</GlobalNamingResources>

<Service name="Catalina">

<Connector
port="8080" maxHttpHeaderSize="8192"
maxThreads="150" minSpareThreads="25" maxSpareThreads="75"
enableLookups="false" redirectPort="8443" acceptCount="100"
connectionTimeout="20000" disableUploadTimeout="true" />

<Connector port="8009"
enableLookups="false" redirectPort="8443" protocol="AJP/1.3" />

<Engine name="Catalina" defaultHost="localhost">

<Realm className="org.apache.catalina.realm.JDBCRealm"
driverName="oracle.jdbc.driver.OracleDriver"
connectionURL="jdbc:oracle:thin:@localhost:1521:orcl"
connectionName="testName" connectionPassword="testPass"
userTable="users"
userNameCol="user_name"
userCredCol="user_pass"
userRoleTable="user_roles"
roleNameCol="role_name" />

<Host name="localhost" appBase="webapps"
unpackWARs="true" autoDeploy="true"
xmlValidation="false" xmlNamespaceAware="false">
</Host>
</Engine>
</Service>
</Server>
Tables
create table users
user_name varchar(15) not null primary key,
user_pass varchar(15) not null
create table roles
role_name varchar(15) not null primary key
create table user_roles
user_name varchar(15) not null,
role_name varchar(15) not null,
primary key( user_name, role_name )
select * from users;
----------------------+
| user_name | user_pass |
----------------------+
| tomcat | tomcat |
| user1 | tomcat |
| user2 | tomcat |
| user3 | tomcat |
----------------------+
select * from roles;
| role_name |
| tomcat |
| role1 |
select * from user_roles;
-----------------------+
| role_name | user_name |
-----------------------+
| tomcat | user1 |
| role1 | user2 |
| tomcat | tomcat |
| role1 | tomcat |
-----------------------+

Jan 2, 2008 11:49:35 AM org.apache.coyote.http11.Http11Protocol init
INFO: Initializing Coyote HTTP/1.1 on http-8080
Jan 2, 2008 11:49:35 AM org.apache.catalina.startup.Catalina load
INFO: Initialization processed in 734 ms
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardService start
INFO: Starting service Catalina
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardEngine start
INFO: Starting Servlet Engine: Apache Tomcat/5.5.9
Jan 2, 2008 11:49:35 AM org.apache.catalina.realm.JDBCRealm start
SEVERE: Exception opening database connection
java.sql.SQLException: oracle.jdbc.driver.OracleDriver
     at org.apache.catalina.realm.JDBCRealm.open(JDBCRealm.java:684)
     at org.apache.catalina.realm.JDBCRealm.start(JDBCRealm.java:758)
     at org.apache.catalina.core.ContainerBase.start(ContainerBase.java:1004)
     at org.apache.catalina.core.StandardEngine.start(StandardEngine.java:442)
     at org.apache.catalina.core.StandardService.start(StandardService.java:450)
     at org.apache.catalina.core.StandardServer.start(StandardServer.java:683)
     at org.apache.catalina.startup.Catalina.start(Catalina.java:537)
     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
     at java.lang.reflect.Method.invoke(Method.java:585)
     at org.apache.catalina.startup.Bootstrap.start(Bootstrap.java:271)
     at org.apache.catalina.startup.Bootstrap.main(Bootstrap.java:409)
Jan 2, 2008 11:49:35 AM org.apache.catalina.core.StandardHost start
INFO: XML validation disabled
Jan 2, 2008 11:49:36 AM org.apache.catalina.core.StandardContext resourcesStart

TS3694 good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

No problem, glad to help!
Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

I have a problem with my VGA output.

Similar Messages

Maybe you are looking for