I have a serious problem, I've tried everything...

Hi, I've had an iPod 20gb Photo for a year and a half. Everything has been great until last weekend. I plugged my ipod into my friends PC and his PC froze. Nothing happened for a good 15 minutes so I just said "Screw It" and unplugged it. I had no music on my Ipod, but the weird thing was, was that in my "About" section, it said "Songs: 0, Capacity: 0kb, Available: 0kb". I went home and restored it, but in the midst of Restoring it said "could not be restored (1418)". I tried EVERYTHING, I put it into disk mode, tried it, nothing. I used my apple Disk Utility, nothin'. I've done EVERYTHING. Is there ANYTHING I can do to fix it?

Since the release and update of iTunes 7, I have not faced any problem, but I heard a lot of articles from this forum about the errors 1417, 1418, 1428 and 50 etc. I could not make any suggestion and find a solution about it, all I could do is to copy some threads from some successful cases mentioned on this forum.
Until yesterday, I finally received a 4th Gen 20GB iPod (around 2 years old)from a friend and asked me whether I could fix it for him, which has been left untouched as a paper-weight for almost 2 months.
I tried to turn it on, and the screen was completed blank and the device looked dead. Before doing anything I prepared the following:-
1. A window based PC
2. A Mac computer
3. An USB iPod cable
4. A Firewire iPod cable
5. An iPod AC charger
As the iPod was previously formatted on a PC, therefore I tried to plug it with a PC via USB cable, it did not response and not able to get recognized by the PC. I ejected the iPod and connected with an AC charger, after a few minutes, I did a Reset for the iPod
How to reset iPod
http://docs.info.apple.com/article.html?artnum=61705
The iPod showed an Apple sign, it stuck there for almost a minute, the screen then showed a battery with an exclamation mark sign, and after a minute, the iPod turned off itself. I was sure that the iPod carried very low battery, and could not be charged by connecting it with any computer (both Mac and PC).
I decided to let it have a charge with an AC charger for a bit longer, after 10 minute I did the Reset again, this time a sign of folder with exclamation mark showed up after the Apple sign, and again could not get recognized by a computer.
I changed my mind, and put the iPod into disk mode
Putting iPod into disk mode
http://docs.info.apple.com/article.html?artnum=93651
Instead of connecting with a PC, I plug it with my Mac using a Firewire cable, it did not response, so I switched the cable to an USB, interestingly, the iPod got recognized and a window pop up indicating that the iPod needed to do a Restore. Therefore I clicked “Restore”, after a few seconds, an Error message pop-up with Error Message 1417, the sign that I have been waiting for quite sometime.
I ejected the iPod and the screen immediately showed a folder exclamation mark (a sign indicating a corrupted or a failure iPod OS). I am forced to put the iPod into disk mode again, connected with the Mac computer and open the Disk Utility
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
It managed to complete the Restore process, and started to sync with the iTunes. However, it got stuck at the song no.238 from the total of 2000. I left it for an hour, but with no process, instead the iPod became “Hot” and the iTunes showed an Error message of 1428. I ejected the iPod from my Mac computer, the iPod’s screen turn to show the famous killer icon;“The Sad iPod“.
This time it was totally dead, even failed to put it into Disk Mode and non of the computer could recognize it. Sigh, I hated to do it but I knew that I must did the following:-
Holding the iPod in my Palm, and hitting it on a surface of a Sofa with 5 attempts.
Did not surprise me, the iPod turned on and it showed the Language Menu on the screen. So, I put it into Disk Mode and connected with my window PC.
The PC showed a sign and indicated that an USB device had been connected with it. I opened the iTunes and did a Restore there.
However, an Error Message 50 showed up, but I were not worried about it, connected it back with my Mac computer with it in Disk Mode. As expected the iTunes opened and allowed me to do a Restore there.
This time it managed to complete the process and a window of register pop up. After the completed the process, the iPod started to sync with the iTunes again, which finally managed to complete the process.
I left it connecting with the AC charger overnight. In the next morning, I switched it on and have a play with it, I am so glad as it is working like a charm.
From the above experience, I would like to share it with the user the following:-
1. It always better to charge with an ac charger instead of the computer, as when an iPod carrying with very low battery, it may not able to get charge from a computer
2. Try to connect the iPod with a computer, switching between USB and Firewire
3. Try to format an iPod with HD problem, with a different kind of computer e.g. Mac or PC, as the formats are totally different, the way it formats may able to solve the bad sectors on the HD
4. It may get better chance to get your iPod recognized, if you put it in Disk Mode
I hope the following works in your case as I did.

Similar Messages

  • HELP ME I have a serious problem on my macbook pro HELP ME

    I have a serious problem on my macbook pro, after I made this tutorial this link:http://tonymacx86.blogspot.com/2010/01/tweaking-your-system-install-chameleon.ht ml, I could no longer install windows on mymacbook pro, already tried everything, according to my knowledge. already formatted, re-formatted, reset EFI, PRAMetc., nothing worked. Ever tried installing on different operating systems, versions of Windows 32 and 64 also, nothing worked.I'm sure that something strange aocnteceu after this tutorial I did,because before I was usually running windows on my mac. The error appears to me is: "Can not partition this drive because some files can not be removed." Sometimes I can go, but time to install windows and choose the partition BOOTCAMP, I get a message saying that the exclamation windows can not be installed on this partition, but maybe my BIOS is not supportedfor this installation. PLEASE HELP ME I'M DESPERATE AND NOT KNOW WHAT TO DO MORE. WAIT HELP
    RICARDO

    I did not know that the chameleon installation was just for Hackintosh, was lack of attention, my bad!!! I will try your method now. In a moment I'll tell you if it worked.
    "My hd"> library> preferences> SystemConfiguration>com.apple.Boot.plist: This way is correct?????
    Content of my "com.apple.Boot.plist:
    <? xml version = "1.0" encoding = "UTF-8"?>
    <! DOCTYPE plist PUBLIC "- / / Apple / / DTD PLIST 1.0 / / EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
    <plist version="1.0">
    <dict>
    <key> Kernel Flags </ key>
    <string> </ string>
    </ dict>
    </ plist>
    NOTE: When I did that tutorial I do not modify this file "com.apple.Boot.plist"
    Wait reply.. Tks !!!

  • HT5622 hey! i have a serious problem coming up which is that i am asked to enter my billing info even for free apps. why should i pay for apps which are free? please help me with this problem!

    hey! i have a serious problem coming up which is that i am asked to enter my billing info even for free apps. why should i pay for apps which are free? please help me with this problem! and in the billing info there is pop-up box saying i have accessed my account from didfferent computer but no i have been doing it from the same pc. please help me out.

    Tap Settings > General > International. Make sure the Region Format is correct.
    As for your Apple ID. Tap Settings > Store > Apple ID > iForgot
    Resetting your Apple ID may help.
    Congrats on your new iPad !!!

  • Hi All,I have one serious problem regarding sap b1.

    Hi All,
    I have one serious problem regarding sap b1.
    In Sales order whenever I select the item from list or tax from list one. I got this
    Msg Box (Application has a problem. Diagnostic file c|:\Program file\SAP\sap Business one \Log\Sap Business one_20080602105441.dmp was created.
    Please contact support and attach diagnostic file). When select ok sap b1 application close. If anyone required screen short of all this error  plz give me Ur email id I will send u.
    Can any one help me?
    Awaiting Early Response
    Regards
    Rajkumar Gupta

    Hi Rajkumar,
    create a message at the marketplace and send them the diagnostic file with an error description.
    lg David

  • Hi apple *sigh* i have a serious problem with my imessage... when i try to open it, it automaticlly sends me back to my homescreen... hope someone knows this problem, thanks

    Hi apple *sigh* i have a serious problem with my imessage... when i try to open it, it automaticlly sends me back to my homescreen... hope someone knows this problem, thanks

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:
    iOS: How to back up
    - Restore to factory settings/new iOS device.

  • I recently updated to the latest version of iTunes and now get a message saying 'Registry settings for iTune drivers are misng for Cd burning' I have uninstallled and reinstalled iTunes and tried everything to repair the problem but still have no optical

    I am using OS  64 bit Windows Vista Home Premium and recently updated the latest version of iTunes. (I only have this CD burning software on my Laptop). Ever since updating, I  received the message 'Registry settings for the iTune drivers are missing for CD burning'. The drivers for Lower and uppper filters in the registry are missingand I now have no optical drive.  I have unistalled and  reinstalled Itunes and manually entered the filters. Have tried everything including something called GEAR driver installer which was suggested on several technical sites. Everything  was working fine in iTunes until I updated it.. It's strange I can still import music but not burn?? Friend s have told me they have ha dthe same problem when updating iTunes but resolved the problem by uninstalling/reinstalling or altering registry keys.
    Today I went to use my Epson Printer and now have problems with it not working. I decided to uninstall/ install printer software and  still can't get it to work either. I may be wrong but his all seems connected to me?
    I have been trying for days to get  telephone support and  been told today you have to pay
    Please can someone help me before I throw the lot out the window!!!!

    Many thanks b Noir
    This is a copy of ONEof the keys  in the registry I changed  as told by Apple support today. I also have changed others as instructed by GEAR  software support to manually delete GEAR drivers (that I had installed but couldn't delete some of the others  they mentioned from Windows system 32. Then some bright spark at work told me I need the Gear drivers so  I downloaded the software and installed again.
    Sorry, just this minute went to insert image  and it is giving me a message saying this sort of content  is not allowed?.
    The most recent key I altered is in: HKey _local _machine. System\class - 4D36E965-E325-11CEBFC1-08002BE10318. Upper Filter data: Upper filter NTIDrvr  SiRem GEARAspiWDN.
    The GEARsoftware info about manually deleting  GEAR drive is from:
    http://www.gearsoftware.com/wiki/index.php?title=DRIVERS:_Windows_-_Updating%2C_ removing%2C_64_bit_versions%2C_etc
    I hope you can help

  • I have a serious problem while I render H.264 with After Effect CS6

    The same file I made with After Effect CS5, while I Use CS6 to open it, system told me to save as 64Bit new version, then I tried to render H.264 mp4 file, but the program always shut down at the final procedure, I try 10+ times with difference file and same result, But I have got no problem if i render AVI file first then convert H.264 mp4 with media encoder. also I try to render to .F4V  its work
    rember I have got the last update version.
    can someone help me, or anybody got a same problem
    this is the error message............

    Thank you Mylenium
    this is my setting

  • MY IPAD 3 HAVE SOME SERIOUS PROBLEMS

    Hello Everyone
    I have a  16gb ipad 3 and it got problems , since i updated it to the new version i had some serious problems ,
    My ipad will not turn on when it plug in to the charger that on the wall or my ipod dock that i normally charge it on , it come up with the battery signal when it on charge and in the battery signal theres red lines through it and it goes to the apple logo after that it turns off  and starts it again , ive reboted it , ive downloaded itunes agian to restart it that way but it wont come up on it at all . it starting to **** me off .. it has run off the 9o days  or so period .. my last report that is to ring them to see if they can help . My ipad has a lock on it too and it has never done this before .......
    Thanks Everyone
    From Australia xx

    Hello Krystal,
    I would be concerned too if my iPad was not charging.  I found an article with steps you can take when you encounter an issue like this.  I recommend following the steps below (these steps refer to an iPhone, but the steps also are relevant for an iPad):
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 30 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    You can find the full article here:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Once you get your iPad running again, follow the steps in the article below if you do not recall your passcode:
    iOS: Forgotten passcode or device disabled after entering wrong passcode
    http://support.apple.com/kb/HT1212
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • TS1398 Turn the wifi on and off? I think I have a serious problem here. I cannot even press the on and off because its not available (the color is grey not black). I think this is why Apple is constantly losing a buyer and user. Slow action.

    What is the problem here Apple? Please hear us. I turned on my Wifi and then turned it off after use. After that I noticed something strange because I cannot turn on the wifi button anymore. I have restarted the phone several times, and turn it on after 10 mins, sometimes 30 min - 1 Hr. but then again its not working. I encountered this problem after updating my iOS to 6.1.2! Please hear us. If you wanted to penetrate to the market please love your consumers. Your products are great but your actions to their(US, CONSUMERS)  problems in terms of bugs fixes and battery life is so slow. Why is that?

    Try the suggestions here to see if they resolve your problem:
    http://support.apple.com/kb/ts1559
    If these don't work you may have a hardware problem. Visit an Apple store for an evaluation or contact Apple Support.

  • Updated feed problem, PLEASE help, tried everything....

    Ive seen this same issue here in forums with no solution:
    Service Provider hosting my old feed was going down in a month...
    I placed the correct update tag in my feed to point to the new feed....
    1 month went by, the server went down...
    my new feed is valid at feedvalidator.org...
    http://www.lmsound.com/649/podcasts/649filmsPodcast.xml
    i have also set it up at:
    feed://feeds.feedburner.com/649films
    In iTunes podcasts, you can find me, however it is still pointing to the old address....
    ANY help would ever so sincerely be appreciated... I have tried everything i can think of... I was concerned about loosing my subscribers, and now i am totally lost here....
    Message was edited by: 649films
    wanted to list the feedburner address as well

    odd...I just pinged your feed using the FEEDID and got a "Podcast ping recieved" that shows your old URL.
    https://phobos.apple.com/WebObjects/MZFinance.woa/wa/pingPodcast?id=121942193
    This is your podcast right?
    http://phobos.apple.com/WebObjects/MZStore.woa/wa/viewPodcast?id=121942193
    Possibility again that if iTunes didn't grab the feed with the <Itunes:new-feed-url> tag, it never updated its database.
    It's tricky with your existing subscribers. Theoretically, if they subscribed before the old server went down, they should have received a copy of the new XML which would include the new feed url and their iTunes client would have updated itself to point to the new feed...granted they started up iTunes before the old server went down.
    If they subscribed after the server went down, (i.e today), they won't get any episodes (it's still pointing to the old server).
    You only have really two options to fix iTunes to point at the correct URL:
    1) See if you can get access to the old server again at the old URL, put a copy of your new feed there which includes the <itunes:new-feed-url> tag. Then ping iTunes...sit back and wait until you can verify that iTunes changed the url it has in its database to the new one. You can subscribe to the feed and check the "show description" or continue to ping iTunes until it shows the correct URL in the "podcast ping received" results.
    2) Remove the podcast and re-submit. Click the "report a concern" button for your feed in iTunes and choose the option to remove the podcast. Then re-submit.
    Itunes provides no real way of knowing how many subscribers you have nor does it keep a list of subscribers. They are just playing matchmaker...just providing a list of podcasts and allowing people to subscribe to the URL you have listed. Once they have subscribed, they don't go back to the iTunes directory...they go straight to your URL.
    Some podcast services like "Feedburner" can keep track of metrics and can give you data on subscribers and episodes downloaded.
    Erik

  • HT4623 I have lost the airplay icon and tried everything on the help site. Anyone help?

    I have lost the airplay icon on my iPad. Tried everything on the help site. Can anyone help?

    Hi, Sean5656. 
    Thank you for visiting Apple Support Communities.
    Sometimes closing all applications in multitasking and power cycling the device can resolve the issue.  However, further troubleshooting may be needed.  Here are the best articles to help you troubleshoot this issue.
    iOS: Force an app to close
    http://support.apple.com/kb/ht5137
    iOS: Troubleshooting AirPlay and AirPlay Mirroring
    http://support.apple.com/kb/TS4215
    Cheers,
    Jason H.

  • Help! Have a serious problem with macbook pro!, please see description!

    so, this must have been about a month ago at the most when it started playing up. basicly, I noticed that A-it has all of a sudden become allot slower than before, B- applications are crashing regularly, this seems to be getting worse and worse, C- i had an incident once or twice where for no reason what so ever the macbook pro simply shut down and restarted for no reason, and with no error message, (though the more recent sudden shut downs give me a message on restart).
    I first investigated the problem when I was playing skyrim, using bootcamp of course to run windows, as I do with many games. After owning the game for about two weeks, and it playing fine, it just crashed and bluescreened all of a sudden without warning, and from that moment on i was unable to play the game since every 5 or so mins in it would crash to desktop or just bluescreen. i thought that this was an error with steam or with the game, and so i looked for help on the steam forum. as i was going through various methods to solve the problem, it seemed that the problem was worsening, since the windows partition begun to bluescreen more often for no reason, and then i noticed that the mac os partition was unexpectedly shutting down for no reason more often aswell, and so i have abandoned my attempts to fix what i thought was an error with windows, and i now believe that it is something more serious. im not so sure what i should do in order to solve this, i know my way around a computer, but im not genius at them, and so i have come to the apple forum seeking help!!
    here i have attatched info that may help, and by the way, it is 64 bit windows 7 that is installed on the bootcamp partition.
    the following message on the bluescreen report makes me think its something to do with the graphics drivers, and so i reinstalled all of the drivers on windows, but this did absolutely nothing unfortunately.  'dxgmms. sys error'

    UPDATE: after verifying and repairing permisions using disk doctor, things seemed to be on the up, but i think this was just hopefull thinking, since it has now got A LOT worse. i can no longer log in to my mac os partition, as soon as i get to the log in page where i type my password in, after typing it in and pressing enter, it will log in for a few seconds and then before i have a chance to do anything, log me out!! this is very very odd indeed!!!

  • I have a serious problem with my lumia

    Recently, Lumia Cyan was released for my model(720), so I tried to download the update.
    But everytime I look for updates It gets stuck on "Searching" and nothing happens.
    I thought that it was for the memory so I left some space, and guess what. Nothing!
    I tried to install the update via PC and i couldn't do it.
    I did so many Soft-Resets and I Uninstall so many important apps.
    I want to do the hard reset but I don't want to lose all my Music and Photos.
    I hope your answer soon, because I'm too tired and disturbed about this problem
    Thank you very much.

    Hi, Percal. If you have not received any notification that the update is available or when you check for it by going to Settings > Phone Update and it said that your phone is up-to-date, this means the update is not yet available for your phone.
    Where are you located? Where did you purchase the phone? You may check the availability of the update by visiting the below link:
    http://www.nokia.com/global/support/software-updat​e/wp8-software-update/
    Aside from what @Sergio_Sz mentioned, you may check this link for the additional tips: http://www.windowsphone.com/en-us/how-to/wp8/basic​s/solutions-to-update-issues.
    "Your phone supports wireless Over the Air (OTA) updates and there is no need for cables or computer. Just download and install the update using your phone."
    BTW, there's no need to perform a hard reset (Settings > About). To avoid data loss, you can back up your files by going to Settings > Backup.
    It's best to wait. :-)

  • Hello Guys, I have a serious problem with Installation of OSX

    Hello ,
    I am using LION OSX 10.7.3 . Day before Yesterday I lost all my contacts in the address book and iTunes window opens without my intervention. I called to the apple care and said the problem they simply said to reinstall the OS. I noted the detailed procedure and formated the Hard disk put my Snow Leopard 10.6 and booted . After selecting all the launguage setting and agreeing the terms and conditions, I got my hard disk in view with an yellow triangle and exclamatory mark in it . There was a message saying I can't install the OS in this Hard disk.
    Please help me guys ..... Thanxs .

    srinishanthreddy wrote:
    There was a message saying I can't install the OS in this Hard disk.
    Because your attempting to install a earlier OS X version 10.6 and you have a newer OS X version 10.7
    You need to remove your personal data off the machine first, then your open to fixing your computer.
    You need to learn about Lion Recovery, it's a bootable partiton that's just like a OS X install disk.
    Read through the User Tip's here, it has links to explain how to do things properly, including backing up your data off the machine, Lion Recovery etc.
    Learn before you burn
    https://discussions.apple.com/docs/DOC-3046
    https://discussions.apple.com/docs/DOC-3045
    https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

  • I have a serious problem with GridBagLayout please help

    I have an working code of an Swing application that has used gridbaglayout it works very well in desktop pc on 2000/xp with 800 x 600 screen resolution but the problem is when i change the screen resolution to higher say at 1152 x 864 resolution then the same code all the components are left align and not properly distributed even though i have GridbagConstraints.BOTH for the fill variable of the Gridbaglayout. Also i am facing similar problem when i run the code on the laptop.
    Please help me and can anyone tell me what to do in case i want the layout to show in the same manner for higher resolution as it is showing for lower resolution.

    you may have to setPreferredSize to a calulation from the screen resolution, if there is 1 thing that is 1 pixel too big for it, i find it stuffs the entire container
    Drogo

Maybe you are looking for

  • Pathetic service by Service centre in ahmedabad and blackberry

    hi i purchased a BLackbery Z10 last month but in few days its was not performing well so i gave it to the service centre for repairing . the concerned person told that there is a serious problem but dont worry we will replace this handset with a new

  • 28 doesn't work, 29 is OOGLy

    in v28 most links from my pop3 mail stopped working but version 29 is nasty looking at the top,, which is worse than not being able to link from email anymore so I went back to 28. I've never had this problem before with the links or a new version in

  • BAPI_ACC_... Pb

    Hello, I've tried : BAPI_ACC_GL_POSTING_POST, BAPI_ACC_DOCUMENT_POST and BAPI_ACC_EMPLOYEE_EXP_POST, in order to post (F-02) some expenses note. In all cases, I don't really know how to fill the DOCUMENTHEADER-OBJ_TYPE : 'BBKPF' ? And I ve always the

  • Zen V Plus 4gb Power On/Detection Is

    I bought a Zen V Plus 4gb player on Tuesday (December 3st, 2007) when my old Zen V gb died (and it was out of warranty). I bought this out of familiarity with Creative V series players, and my experiances with them have been positi've so far. However

  • Bex Portfolio control

    hi, Bex Portfolio is for publishing public documents or reports. But we would like to control the users to publish/open only the BI Reports which they are authorized to. for example, if a user has access to finance reports but not to supply chain rep