I have an airport extreem network that works with two MacBooks.  I am trying to get my PC (IBM ThinkPad) to connect to the network.  The PC has airport for the PC downloaded but it will not recognize the network.  Any suggestons please!

I have an airport extreem network that works with my two MacBooks and a iMAC.  I am having no luck in getting a PC (IBM ThinkPad0 that has the PC airport software to be recognized by the network.  Any suggestions?

When you introduced the AirPort Extreme, you had a condition where you have two routers in series. The simpliest solution is to reconfigure the downstream router (in this case the Extreme) as a bridge. This will allow the upstream router to provide the required NAT & DHCP services to all network clients regardless of which router they are connected to.
To reconfigure the Extreme as a bridge, you will use the AirPort Utility. (Note: I will provide the steps for using AirPort Utility v5.x)
AirPort Utility > Select the AirPort > Manual Setup
Internet > Internet Connection tab > Connection Sharing = Off (Bridge Mode)

Similar Messages

  • I purchased a used Ipod touch 4th gen and my computer (Windows XP) recognizes it as a camera but Itunes will not recognize the ipod. Old ipod works and connects fine. Any suggestions?

    I purchased a used Ipod touch 4th gen and my computer (Windows XP) recognizes it as a camera but Itunes will not recognize the ipod. Old ipod works and connects fine. Any suggestions?

    Well, there is always the possibility that it's been jailbroke, in which case, you're out of luck.  However...
    http://support.apple.com/kb/TS1369
    There have been some problems accessing pages on the Apple web site.  If the hyperlink gives you a "We're sorry" message, try again.

  • Whenever I update from Windows 7 get error 1602, iPod shows USB connection to iTunes, but iTunes will not recognize the device. None of the Apple documentation helps.

    Whenever I update from Windows 7 get error 1602, iPod shows USB connection to iTunes, but iTunes will not recognize the device. None of the Apple documentation helps. The Apple Mobile Device driver is loaded and operating. The anti-virus software and firewall are not at fault (were uninstalled, and made no difference). The iTunes on my older machine running Vista does recognize the inoperative iPod (iTunes has detetced an iPod in recovery mode) and allows me to restore the device. Can anyone help to resolve this problem on the Windows 7 PC?

    So yu tried all of this:
    Error 1600, 1601, 1602: Try the following steps to resolve this error:
    Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable.
    Follow the steps listed for Error 1604.
    This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in this article for details on troubleshooting security software.
    Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
    Restore and wait for error 1604.
    When prompted, click OK.
    Close and reopen iTunes while iPhone remains connected.
    iPhone should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
    If you had then time for an appointment at ther Genius Bar of an Apple store.

  • My ipod touch is now disabled after entering the wrong passcode too many times.  How do I enable it again - it says "connect to itunes" but itunes will not recognize the ipod because it is disabled.

    My ipod touch is now disabled after entering the wrong passcode too many times. t says "connect to itunes" but itunes will not recognize the ipod because it is disabled.  How do I enable it again?  Thanks!

    iOS: Unable to update or restore

  • Running parallels with windows xp. want to upgrade my Quickbooks to 2013, but it will not recognize the disc.  Help!

    running parallels with windows xp and OS X Lion.  Trying to upgrade my Quickbooks on the windows side to the new 2013 version.  The windows side does not even recognize the disc.  What am I doing wrong?

    S that QB edition is only for windows 8. It won't run on any earlier version of windows.
    Looking at the QB 2013 system requirement it runs on XP.
    http://support.quickbooks.intuit.com/support/articles/INF21187
    So the version of windows is not your problem. Your problem is the virtual machine is not se to use the mac dvd drive. Have you looking into the machine settings. Not windows settings, the virtual machine settings. Make sure it is set to connect the mac dvd drive to the virtual machine.
    A good place to start would be the parallels help system. Not the windows help system.

  • 9.1 downloaded, but it will not install???? Please help!

    I am a long time Mac user. Bought myself a new iMac for my studio. Everything works fine. I have downloaded the 9.1 update and when I install it, it tells me that it cannot install as I already have 9.1, but I do not have 9.1. I am running 9.02.
    Any ideas? Driving me nuts this one.....

    I am having the same exact problem.. only i could of sworn i downloaded & installed the 9.02 update, but when i go to check my about logic pro, it says.. 9.0.0... I'm completely baffled by this. I bought the logic studio upgrade, successfully installed it, THOUGHT i had registered it, apparently NOT, when i tried to download the update. Like what is seriously wrong with this? I am VERY frustrated. I have a 8 core nehalem processor, running mac osx 10.6.2.
    I know alot of people are experience the same problem. Apple has officially let us down fellas.

  • HT1918 I am trying to update my info in iTunes but it will not recognize the changes

    I am trying to update my info from USA to my new address in Canada but the system is not recognizing my cc info

    jonathanfrommcallen wrote:
    I am trying to update my account in iTunes but it asked me to spend all the money that I do have on my account before !! for that reason I would like to know How can I spend 0.16 $ in iTunes ?
    How are you trying tp "update" your account?
    Changing countries?

  • My .me mail account has converted to iCloud. My desktop Mac will not recognize the password. Any resetting makes no difference. Should I delete the mailbox and reload it?

    My Mail application on my desktop iMac has converrted my original .me account to an iCloud account. It keeps asking for the password and rejects the original one. I've tried changing the password and it still rejects it. I've tried using my Apple ID password and that is rejected too.  Should I just delete this mailbox. And then reset it up with new account information?  Then would I lose all the e-mails or will they "reappear"?   Thanks for any tips!

    If the old ID is yours, and if your current ID was created by editing the details of this old ID (rather than being an entirely new ID), go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID.  Click edit next to the primary email account, change it back to your old email address and save the change.  Then edit the name of the account to change it back to your old email address.  You can now use your current password to turn off Find My iDevice, even though it prompts you for the password for your old account ID. Then save any photo stream photos that you wish to keep to your camera roll.  When finished go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud).  Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was.  Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

  • I have a tungsten e2 that will not recognize the sd card. I have tried multiple cards and none work

    I bought a older tungsten e2 for use in the field but it will not recognize the sd card!  Any ideas?  I have tried multiple cards and it will not recongize any so far!

    PalmBlue wrote:
    775boomer,
    There is a SD card size limit for Palm Devices. 
    What is the smallest size you have tried?
    http://h30434.www3.hp.com/t5/Palm-OS-WinMo-Hardware-and-Software/Maximum-quot-Tested-quot-Expansion-...
    Please visit this linked thread.  I have updated the link contained in the first post to the Palm Powerups site where there is a utility available which allows the use of larger capacity SDHC cards in Palm OS devices.
    smkranz
    I am a volunteer, and not an HP employee.
    Palm OS ∙ webOS ∙ Android

  • HT1918 I have changed my new apple email address at the itunes store but when I try to buy an app on my iPad my old apple id (email) comes up and will not recognize the password. How do I change this? I tried going in through settings/tapping apple ID to

    I have changed my Apple ID when I got a new email address and confirmed it. However when I go to my iPad to buy an app my old Apple ID comes up and will not recognize the password. I tried going into the settings on my iPad and tapping on the old Apple ID to go in to change it but it will not recognize it and I cannot get in on the iPad to change it. How do I change this ID on my iPad for the iTunes store?
    Jaylsworth

    How did you fix this??

  • I have tried to download a Premier 6 trial three times but it will not finish the download.  How do

    I have tried to download a Premier 6 trial three times but it will not finish the download.  How do I get it to finish?

    Thanks for getting back to me:Mac os 10.8.2.The error code is 109. "check your network or destination disk."  Network connection is flawless.  Destination disk is brand new imac.I have not tried to download from anything but safari which has worked perfectly for all downloads in the past.Any ideas?Thanks
    Date: Sat, 2 Feb 2013 22:04:27 -0800
    From: [email protected]
    To: [email protected]
    Subject: I have tried to download a Premier 6 trial three times but it will not finish the download.  How do
        Re: I have tried to download a Premier 6 trial three times but it will not finish the download.  How do
        created by Rave in Downloading, Installing, Setting Up - View the full discussion
    Please let me know what OS are you using and if any error comes up during the download.
    Also let me know if you have tried downloading from a different browser.
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/5043725#5043725
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/5043725#5043725
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/5043725#5043725. In the Actions box on the right, click the Stop Email Notifications link.
         Start a new discussion in Downloading, Installing, Setting Up by email or at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • I have a sony rx100 and my version of lightroom (4) will not recognize the raw (.ARW) files. Please help!

    I have a sony rx100 and my version of lightroom (4) will not recognize the raw (.ARW) files. Please help!

    I have version 4.4.1 on my computer now, which is functioning properly - but does not read the .ARW files. When I download the link you sent and try to open it, it pops up as version 5 and I get this image (attached). This is my first time in one of these threads, not sure if i have to reply to each of you individually?
    DdeGannes, could you please tell me how to recover the serial number from my operating system?
    Thank you SO much everyone!

  • I am using an epson projector to present images downloaded to a thumb drive. I renames the images on export to "untitled 101, 102 etc. The projector will not recognize the sequence. It wants 001, 002etc. If I try to start 001 lightroom changes it to 1, 2

    I am using an epson projector to present images downloaded to a thumb drive. I rename the images on export to "untitled 101, 102 etc. The projector will not recognize the sequence. It wants 001, 002etc. If I try to start 001 lightroom changes it to 1, 2  ... 10,11 etc. How can I export and rename starting with 001?

    The projector may actually be processing a 3 digit number in numerical sequence.  Have you tried your export/collection in order  sequence starting with 101?  Assuming you have fewer than 899 images you should be OK. (I had to fiddle with export sequence for a display frame which used the file date and time for sequence!)

  • I have changed to AT&T U-verse, which has a new modem and router combined.  Safari 5.1.10 will not recognize the wifi signal, but Foxfire will.  What settings do I need to change on Safari?

    I have changed to AT&T U-verse, which has a new modem and router combined.  Safari 5.1.10 will not recognize the wifi signal, but Foxfire will.  What settings do I need to change on Safari?

    Hello SalsburgD
    The first thing I would check is to make sure that the router is using the recommended settings to get online. Another troubleshooting step is to create a new Network Location and then join your network to see if that changes things. 
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    Using network locations (Mac OS X v10.6 and later)
    http://support.apple.com/kb/ht5289
    Regards,
    -Norm G.

  • I am trying to hook my macbook pro to a sony bravia TV via DVI to HDMI cable and the TV will not recognize the signal. The same set up has worked with three other, though different televisions. Any thoughts?

    I am trying to hook my MacBook Pro to a Sony Bravia TV via DVI to HDMI cable and the TV will not recognize the signal. I have used the same setup with three other TV's, each a different brand with no problem. Any ideas?

    Is the TV set to take input from the HDMI connection?
    On your computer, if you open the Displays preferences and do not see an Arrangement tab (or there is an Arrangement tab that shows only a single monitor) then there is something physically wrong with your connection.  Try clicking Detect Displays just to see if the computer can now sense the presence of the connection.  Check your connections.
    If you do have an Arrangement tab, and it shows two screens, then click Gather Windows to bring the TV's Displays preferences on to your main screen if the TV is not yet showing an image.  Set the proper resolution (probably 720p, 1080i, or 1080p).  Set the refresh rate (probably 60Hz) if that preference is shown.  You should see a picture at this point.  I  recommend turning off mirrored displays if it is enabled.

Maybe you are looking for