I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help.
They said I need to change my settings to NAT settings. I haven't been able to figure out or find anything. I have also spoken to Apple Support on the phone for hours without being able to figure out how to do this ( i don't think he knew much either lol.) Please help me because I've got about 15-20 devices in my house that require to be connected to the internet and this is just making things ridiculously slow and painful for me.
Thanks!

It is on DHCP & NAT under router mode yet my isp is still the one issuing ip addresses to my devices instead of the router issuing them

Similar Messages

I was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

i was using time capsule to extend a network. now i want it to be the primary base station. how do i convert this?

Thanks for the info. Since this is a cable modem, you will need to fully reset it so that it will associate correctly with the Time Capsule when it is reconnected.
I don't have the manual for your Ubee model handy, but most modems will reset if you power them down completely. That means pulling the power cord from the back of the device or unplugging from the wall. Leave the modem powered off at least 30 minutes...longer will not hurt a bit.
Next, perform a Factory Default Reset on the Time Capsule per this document:
Resetting an AirPort Base Station or Time Capsule FAQ
After the modem has been powered down and Time Capsule has been reset, connect an Ethernet cable from the modem to the WAN port (circle icon) on the Time Capsule.
Power up the modem and let it run for 2-3 minutes by itself
Then power up the Time Capsule and let it run a minute or two
Next, open AirPort Utility and configure the Time Capsule to "Create a wireless network". Let us know what operating system you are using on your Mac or PC if you have additional questions or need more details on this.

HT1692 I have duplicate contacts for every contact. How can I fix this problem?

I have duplicate contacts for every contact. How can I fix this problem?

Hi again,
I found a previous thread on this that may resolve your problem:
If you are syncing over the air with iCloud then DO NOT sync via the cable with Contacts. This causes duplicates. You are telling the iPhone to bring what is in those programs to the iPhone (one copy). Then you are syncing from the cloud (copy two).
The iPhone will do exactly as you tell it to do.
The easiest way to remove duplicates.
1. On the info tab in iTunes uncheck sync contact and sync calendars.
2. On the iPhone>settings>mail contacts calendars>@me.com account>slide Contacts and Calendars OFF
3. Log into iCloud and look at contacts and calendars and make sure there are no duplicates.
4. On the iPhone>settings>mail contacts calendars>@me.com account> slide to Contacts and Calendars ON
When prompted choose to Replace with info from iCloud
Had to update some of it with iCloud info (it had been written for Mobile Me), but hopefully this will work for you!
Cheers,
GB

Using time capsule to extend a 2003 airport extreme

I have a 2003 airport extreme. I have a 2011Time Capsule. How can I use the Time Capsule to extend my range wirelessly?

Unfortunately, this is not possible, since the older AirPort Extreme does not have a setting to "extend a wireless network", which was added to the AirPort Extreme models in 2007.
It might be possible to have the older AirPort provide some additional wireless coverage if it can be permanently connected back to the Time Capsule using a wired Ethernet cable connection.

How can I force my Second Generation Airport Extreme to use 2.4GHz when extending the network of my Fifth Generation Airport Extreme?

Hi,
Would be great if anyone can help. I have setup my Second Generation Airport Extreme to extend the network of the Fifth Generation Airport Extreme. The 2nd generation Airport extreme seems to automatically get set to use 5GHz vs 2.4GHz. I would like to force it to use 2.4GHz so my older devices can connect to it. Any help would be appreciated.
Thanks,
Mike.

Enable the option to assign a different name to the 5 GHz network on your 5th Gen AirPort Extreme.
Then, the 2nd Gen Extreme will only "see" the 2.4 GHz network, and extend that signal.
If you are not sure how to do this, post back to tell us what operating system you are using on your computer so we will know what version of AirPort Utility you are using....so we can provide the correct steps for the setup.

Air port won't turn on, it says AirPort:Not Configured why? how do i fix this help!

I dont know what is going on! My kids did something while I left it charging. It won't let me connect to the internet, its saying Airport off and at first when I tried clicking Airport on, it would'nt work now its in grey saying 'Airport: Not configured'. How do I fix this? help!

What OS X version are you using?
To determine which Mac you have, its OS X version, what kind of CPU it uses, and how much memory is installed:  > About This Mac

I want answers to securtiy question does not have rescue email and does not want to lose the fifteen dollar gift card i just put on my accout by setting up a new one and does not want to lose all my music how can i fix this

i have forgoten the answers to my security questions and does not have a resuce email and i donot want to loose the $15 giftcard i just put on there or any of my music by setting up a new accout and all i use to download items is giftcards. what should i do?

plarkin wrote:
should I do a full reset of TM (per the instructions at the link below) prior to setting up the TC?
I'd start by just selecting the new destination. Do the "full reset" if you have trouble with that.
do I need to set up the network portion first and then turn on TM?
That might make things easier.
even though my mini was previously only connected wirelessly to the old router, I plan to connect via Ethernet to the TC (for one thing, to make the initial backup run faster). Do I just turn AirPort settings off on the mini, or does that need to be on in order to setup the TC?
To assure that your first backup is over Ethernet I'd turn off AirPort until it's done. Check the order in the Network panel of System Preferences. I'd move the Ethernet connection item to the top of the list.
In other words, does the initial setup of the TC from my mini happen wirelessly or over Ethernet?
Either way should work fine.
I currently have a networked printer conneceted to my old router, which I will connect via Ethernet to the TC. Can I assume that, once I have set up all of my family's PCs/Macs/iDevices on the newly-established TC network, that I will have to re-establish connection to the printer as well?
Not necessarily. I'd only do that if the printer isn't available after the switchover.
I would like to reformat the second external drive (the one previously being used for TM backups) for possible reuse with another computer. Can I simply reconnect this to my mini and reformat?
That's what I'd do.
is TM going to see it and try to back it up?
If you've already reconfigured Time Machine to use the Time Capsule drive, there shouldn't be a problem.

I have an old iPod and want to synch some new music to it but the synch is set for all music. How do I change this?

Classic iPod with firewire. Just downloaded a new album that I want to put on it, but iTunes 11 want allow me to sych just some music. How do I switch this so I can upload just the one album?

In iTunes help under synching devices.
Sync your device manually
If you use manual syncing, you can sync items from more than one iTunes library to your iPod. (You can sync iPod touch, iPhone, and iPad with only one iTunes library.)
You can manually sync music, movies, TV shows, podcasts, and iTunes U lessons. You can’t manually sync photos and info (contacts, calendars, bookmarks, and so on).
Connect your iPod, iPhone, or iPad to your computer and select your device.
Click the Summary button and select “Manually manage music and videos” (below Options).
Click the On This Device button.
Click Add To on the right side of the iTunes window.
Drag items from the left side of the iTunes window to the pane on the right. To add other types of content, choose a category from the Library pop-up menu.
Click Done.
Sync your device manually
If you use manual syncing, you can sync items from more than one iTunes library to your iPod. (You can sync iPod touch, iPhone, and iPad with only one iTunes library.)
You can manually sync music, movies, TV shows, podcasts, and iTunes U lessons. You can’t manually sync photos and info (contacts, calendars, bookmarks, and so on).
Connect your iPod, iPhone, or iPad to your computer and select your device.
Click the Summary button and select “Manually manage music and videos” (below Options).
Click the On This Device button.
Click Add To on the right side of the iTunes window.
Drag items from the left side of the iTunes window to the pane on the right. To add other types of content, choose a category from the Library pop-up menu.
Click Done.

I BEG of you: How do I replace an Airport Extreme base station with a 4th-generation Time Capsule as the base station?

I'll be damned if I can figure this out. I have a new late-2012 iMac (OS 10.8.3) connecting to my LAN via Airport wi-fi. (It will be Ethernet-connected, as soon as a hole is drilled into my new work table, but right now the Ethernet cable doesn't reach.) My wife uses a 2011 MacBook Air.
The LAN consists of a flying-saucer-looking Airport Extreme connected by Ethernet to the modem, plus 2 old Airport Expresses. I have an Ethernet switch too, through which I've got a TV connected and a printer connected.
I bought a 4th-generation Time Capsule about a year ago, but couldn't figure out for the life of me how to replace the Airport Extreme with it. I became so incredibly frustrated that I hid it away in a closet until now. I just tried again, with the same results. I've got both Airport Utility 5.6 (to use with the old Extreme and Expresses) and Airport Utility 6.2. I was using version 6.2 to set up the Time Capsule... or to try to. Once again, I cannot for the life of me figure out how to do it! I tried so many different Ethernet wiring connections that I now cannot remember them well enough to describe them here.
I distinctly remember that, when I tried this a year ago with my wife's MacBook Air and Airport Utility 6.2, I was presented at one point with the question whether I wanted to replace an existing base station with the Time Capsule I was trying to set up, but this time I never was presented with that option.
Is there anyone who can, in essence, hold my hand and walk me through this process step-by-step? At this point I even need to be instructed what to wire to what. I feel like a total incompetent.
My MOST sincere thanks in advance for help!
(I hope Time Capsule is the correct forum for this question. I considered the Airport forum as well, but I don't want to cross-post.)
(And, just to complicate matters, after I get this done-- assuming I ever do-- I want to use the old Airport Extreme on the outside of the house to extend the range of my LAN to the back yard... but that's for another day entirely.)

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Awesome Bar will not show browsing history after update - I have location bar set to show from history and bookmarks with history being saved for 10 days. How do I fix this?

I updated firefox last night and now none of my history will show up in my location bar. Everytime I either close the browser window or start a new tab I have to completely type out new addresses.

I'm the original asker. I uninstalled Firefox, including associated personal data and reinstalled. It now seems to work. I used FEBE to reinstall bookmarks and extensions.

Unusual Senario: Use Time Capsule to extend Airport Express network

I have an less common senaria here. I'd like to keep the TC on my desk and hide away the ugly cable modem. This is what I want to accomplish:
- Connect my airport express (802.11n model) to the cable modem and use it as the base station, in b/g/n mode.
- Wirelessly extend the above network to my TC.
- The TC will only be connected via ethernet and N equipped computer, so I want to run it in N (5GHz) only mode.
After some research, it seems to be not feasible, can anybody please confirm? Thanks for help.

If you are asking about extending using wireless only......Yes, if your existing network is being created by another Apple wireless router.
In this case, the Time Capsule would need to be located where it can receive a strong wireless signal in order to extend it correctly.

I have itunes version 8.2 and would like to avoid downloading a newer version. The iTunes Store will not leave the page for iTunes 10. How do I fix this?

The iTunes store will not leave the page for downloading iTunes 10. I just deleted iTunes 10 because of errors to purposely go back to version 8.2. Now I would like to keep 8.2 and not upgrade. How do I get this page to go away, or just keep 8.2? I would like to only have a version before 9.0. Please help!

The iTunes store will not leave the page for downloading iTunes 10. I just deleted iTunes 10 because of errors to purposely go back to version 8.2. Now I would like to keep 8.2 and not upgrade. How do I get this page to go away, or just keep 8.2? I would like to only have a version before 9.0. Please help!

I have disabled my security on my ipod and when ulocking it is asking me for a ulock code how can i fix this?

does anyone have any idea of how to fix this or disable the password

Restore the iPod from the computer to which the iPod is synced. For information and instructions, see:
http://support.apple.com/kb/ht1212
If that will not work, you'll need to put the iPod into Recovery Mode and then try the Restore again:
http://support.apple.com/kb/ht1808
If that still doesn't work, as a last resort try DFU mode:
http://www.iclarified.com/entry/index.php?enid=1034
Regards.

My 4th generation iPod touch stopped giving me notifications on all apps. How do I fix this? (The sound is up, I have wifi, all notification settings are on)

The sound is up, I have wifi, all notification settings are on

Add one more disgruntled user to the list. First noticed that I couldn't download upgrades on my iPhone. It would prompt for password as normal, would briefly show "waiting" on the app icon and then just stops with app store still showing update. True deleting the app and installing from iTunes. This worked, but iTunes library had old version of app so it still showed an upgrade. I then deleted the app from the phone and iTunes and that is when I started getting the 11111 error. I've since discovered that I can download any new content to any of my linked iDevices, but cannot download any type of previously purchased content. No previously purchased music not on device, no previously purchased uninstalled apps, no installed app upgrades, etc. ALL show up in purchased content lists, but when you attemp to download it appears to be starting and then simply fails with no errors on the iDevice(s). I've also tried signing out of my account in settings - store, performing a hard reset and then signing back in, but alas, no success.
C'mon Apple, obviously a problem that is happening to numerous users and it started happening to us all at the exact same time. You got us iAddicted, now give us our iFix.

When setting the midi port for an external device, how do I stop this altering the port setting for a separate external device?

I am using Logic Pro 9.1.7.
I have an EMU sampler set to port D.
And a Roland JV 2080 set to port B.
The ports refer to an external M-Audio Midisport midi interface.
When creating a new track (brand new, not as a duplicate of another) for sounds from the Roland and setting port B in the Inspector, I find this affects certain existing tracks set to port D that are using sounds from the EMU. The latter tracks are converted to port B. I note that only some, not all, tracks are affected.
If I try to change the EMU tracks back to port D, then the Roland track also switches to port D! And so on...
Each device has a 16-channel "instrument" in the Environment (but no virtual wiring anywhere).
Usually, setting channels, banks and programs in the Event List for each track has been able to make things work reasonably well.
Any suggestions that I could explore would be welcome. Thanks.

I haven't checked this with instrument tracks, could it possibly be you have somehow de-selected Universal Track Mode in Preferences/Audio? It should be enabled.

I have an Airport Extreme as my router and am using time capsule to extend the network in my new house. My ISP is only providing me 4-5 ip addresses and wants me to set up my router to issue out new ip addresses for all my devices.How do I fix this?Help

Similar Messages

Maybe you are looking for