I have an Airport Extreme, I want to replace it with a Time Capsule. I swapped my cables to the new TC, unplugged both Cox Cable modem and Airport Extreme. Started up by plugging A/C power for Cox Cable modem, then power to TC. Result is blinking amber

I tried unplugging again and restarting the TC first, still gets blinking amber light. I even reset the TC because I was using it for backups only in the network, I just want to move it to the primary position. I don't even get the option of starting a new network.
I need help.

Blinking amber light is not the issue.. that will involve lots of issues due to your reset.
Make sure you have a computer plugged into the TC by ethernet.. do not do setups over wireless.
Even if you need to do the setup in complete isolation that doesn't matter.. it will work when you return it to the network.
Do a full factory reset.. I am not sure what resets you have done up to now.. full factory means you hold in reset before applying power.. and keep holding in reset until the front led flashes rapidly. About 10sec.
The TC must be in router mode if your cable modem is only a modem.. but I don't know if your cable modem is pure modem or modem router.. if the later then the TC should be in router bridged mode.
Once you have that right.. plug it back into the modem if you had to remove it..
Power cycle again if you need to. It can take 15min or more of modem off to reset the cable setting for MAC address.
Then you can setup wireless, although you can also do it whilst connected by ethernet which is usually better.
What airport utility are you using.. the latest one is too automatic.. stop any attempt to automate the setup and do it manually if you get stuck.
Even use the old utility is sometimes better.. 5.6 can be loaded even on Mountain Lion with a bit of a fiddle.

Similar Messages

Just bought an IPod nano 7th generation. I have a Mac computer OS X v10.5.8 with 10.6.7 iTunes player. To use the new IPod nano I need a OS X v10.6.8 or later and iTunes 10.7 or later. What are my options to upgrade the Mac?

Just bought an IPod nano 7th generation. I have a Mac computer OS X v10.5.8 with 10.6.7 iTunes player. To use the new IPod nano I need a OS X v10.6.8 or later and iTunes 10.7 or later. What are my options to upgrade the Mac?
Thanks to your feedback.

Click here, check that your computer meets the requirements, purchase and install the DVD, and run Software Update.
(74380)

I want to replace my 1st generation time capsule with the new ac time capsule. What might I use the old 1st generation time capsule for

What use would there be for the 1st generation time capsule if I bought a new ac time capsule?

I just bought hte new ac time capsule (TC), and was using the 1st generation one at home.
=> I use now the old TC as an wifi extender and as a shared hard disk for family
=> the new TC is used with Time Machine for encrypted backup and first high speed network

HT1218 i have a windows 8 computer that is not connecting with my time capsule wifi. my other macs and windows 7 systems do connect. is this a firmware update glitch? any suggestions?

I have a windows 8 computer that is connecting poorly via wifi and my Apple time capsule to the internet. My IMac an another windows 7 based computer are connecting fine. This started 6 days ago. And, the windows 8 machine connects well via a hard Cat-5 connection to the time capsule (I'm using that now) and worked well on a wireless netgrear system over the weekend.
I'm thinking an automatic firmware update may have caused this or perhaps i need the time capsule to use something other than a default address. Those are just guesses, but I could sure use some help. Thank you.

It is hard to figure where the issue is..
Certainly if windows updated the wireless driver that can mess things up no end..
What update happened 6days ago?
What TC do you have.. ?? If it is flat one and you updated to 7.6.4 do a factory reset and reconfigure.
If that doesn't work roll the firmware back to 7.6.1 or even 7.5.2 as these are generally superior to windows.
There is no update for TC gen5 yet.

When I remove the battery charger my computer shuts down completely and won't start until I plug the charger back in

When I remove the battery charger the computer completely shuts down and won't start up without the battery charger. I have to restart all my windows when I turn it back on. Before it would just go to sleep and if it was charged it would come back on without batter. Any suggestions on what this can be?

Any suggestions on what this can be?
A dead battery. Buy a new one.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. My question is I now wish to add a second Airport extreme but am considering a hard wire connecti

I have a Airport network at home with a Time capsule connected via ethernet cable to modem. Also the network is extended wirelessley with an Airport Extreme. I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme. Can my network operate properly to extend the network with both a wireless and wired extend functionallity?

I now wish to add a second Airport extreme but am considering a hard wire connection with 100 ft of cat 6 cable from the Time capsule to the second Airport extreme.
Excellent plan.
Can my network operate properly to extend the network with both a wireless and wired extend functionallity?
Yes, but don't get confused about the second AirPort Extreme, as it would not be configured to "extend" a wireless network.....it would be configured to "create a wireless network" using the same wireless network name, security settings and password as the Time Capsule network. Configure the second Extreme in Bridge Mode.
This Apple support document will show you how to hookup and configure the second AirPort Extreme:
http://support.apple.com/kb/HT4260

If I have my iMac internet sharing turned on, the Airport Utility won't recognize the Airport Express I want to use to stream iTunes to my stereo. When I turn the iMac internet sharing off, the Airport Express appears but calls itself a base station.

If I have my iMac internet sharing turned on, the Airport Utility won't recognize the Airport Express I want to use to stream iTunes to my stereo. When I turn the iMac internet sharing off, the Airport Express appears but calls itself a base station. I just bought the Airport Express and it's not clear how I should set up my System Preferences for Sharing. Thx

Yes. Unfortunately the stereo is too far from the wired ethernet connection My iMac is connected to the internet using an ethernet cable from the DSL modem (plugged into the wall, not wireless). The Airport Express is plugged into an outlet 25' away from the iMac and connected to my speakers. I've turned on the iMac Airport wireless Internet Sharing, hoping to stream iTunes to the Express connected to the stereo. The iMac Airport picks up several neighborhood networks so I know it's working (and I connected my iPhone wifi to it just to check as well).
When I use Airport Utility to set up the Express, the only time Utility recognizes the Express is when the iMac Airport is off. When I turn on the iMac Airport, the Airport Utility immediately loses the Express and asks to rescan.
Maybe that explains my problem better.

Power backup for dsl modem and Airport Extreme

Does anyone here have backup power for a dsl modem and Airport Extreme that is successful? I have a name brand power backup and when the power goes off both the dsl modem and Airport Extreme remain on; however, the network connection is lost so the fact that they remain on doesn't help. I have been unable to find anything about this problem on the internet generally and consultation with a well-known squad person has not helped. Any thoughts about this will be welcome.

Yes, I agree. But since the backup power keeps the modem powered, why doesn't the dsl connection continue? The squad person I talked with told me that the speed with which the backup power units replace power during an outage is about the same across different backup brands/units (I don't recall the speed but it was in milliseconds) and should be quick enough to retain the dsl connection. Doesn't happen.

I have a new time capsule how do you turn up the transmitting power for wifi

I have a new time capsule how do you turn up the transmitting power?

Transmit Power is set by default at 100%, the maximum allowed by law.
There are no settings to allow higher output.

What is the best way to hookup my airport extreme with my time capsule ?

what is the best way to hookup my airport extreme with my time capsule ?

It sounds like you have the AirPort Extreme configured as the "main" router on your network.
If that is the case, connect an Ethernet cable from one of the LAN <-> ports on the AirPort Extreme to the WAN "O" port on the Time Capsule
Power up the Time Capsule
Connect another spare Ethernet cable from your Mac to one of the LAN <-> ports on the Time Capsule
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Time Capsule, then click Manual Setup
Click the Wireless tab below the row of icons and make sure that the setting for Wireless Mode = Off
Click the Internet icon, the click the Internet tab
Insure that the setting for Connect Using = Ethernet
Insure that the setting for Connection Sharing = Off (Bridge Mode)
Click the Update button at the lower right of the window and wait a full minute for the Time Capsule to restart
Then power cycle the entire network by powering everything off....order of power down does not matter
Wait a minute
Power up the modem first, and let it run a few minutes by itself
Power up the AirPort Extreme next and let it run a full minute
Power up the Time Capsule next and let it run a full minute
Keep starting devices one at a time about a minute apart until the entire network is back up
You will need to reset the backup path from your Mac to the Time Capsule to get backups going again
Open System Preference (gear icon on the dock)
Open Time Machine
Click Select Disk
Click the Time Capsule to highlight it
Click Use for Backups or Use Disk and backups should begin again in a few minutes
If you do not want to leave the Mac connected to the Time Capsule by Ethernet, remove the Ethernet cable from the Mac to the Time Capsule, then log on to the AirPort Extreme wireless network

AirPort Extreme with 3T time capsule file security question

Right now I am using a MacMini with an external HD as a file server. I'm thinking g of using the new AirPort Extreme with 3T time capsule to do the same tho g (while also extended my wifi reach).
With the Mac mini I have fine control over who gets to see and do what to which folders and files. It seems that with the AirPort Extreme thee is no notion of permissions or access control -- if you can get on the wireless you can access the files. That is extremely insecure.
Is my understanding correct? Is there no way to secure files hosted on an AirPort Extreme so only certain users can access them??
- john

Are there any instructions for how to format and set HFS+ user permissions on the AP Extreme's HDD?
For the formatting part, you will need to temporarily connect the drive to your Mac, and then, use the Disk Utility (a part of the OS X operating system) to partition and format the drive. You should find this utility in the \Applications\Utilities folder. For HFS+, choose "Mac OS Extended (Journaled)" for the Format option.
For assigning user permissions using accounts, you will need to use the AirPort Utility.
Run the AirPort Utility
Select the Extreme, and then, click on Edit.
Select the Disks tab.
Select the HDD in the Partitions window.
Choose "With accounts" as the Secure Shared Disks option.
Click on the "+" button to add user accounts.
For each account desired, enter the Account Name, Password, and File Sharing Access type.
Click Save.
Click Update to write the new configuration information to the base station and wait for the station to restart.

Hi have just purchased iphone 4s . my itunes on my mac is currently 10.4 . 10.5 is needed for the new iphone but when i download it and click on install the itunes about still says 10.4 . have tried to update through itunes but it says there is no softwar

hi have just purchased iphone 4s . my itunes on my mac is currently 10.4 . 10.5 is needed for the new iphone but when i download it and click on install the itunes about still says 10.4 . have tried to update through itunes but it says there is no software available for me . please help . mr frustrated

If your computer is running an OS X prior to Snow Leopard 10.6,
the answer (if it is an Intel-based Mac; not old PowerPC model)
would be to buy the retail Snow Leopard 10.6 DVD from Apple
for about $20, and install it. Then update that to 10.6.8 by using
the installed Snow Leopard online to get Combo Update v1.1 for
Snow Leopard 10.6.8. After that is installed & updated, run the
system's Software Update again, to see what else is available to
that system.
Later systems can then be looked into at Mac App Store, once
the computer is running Snow Leopard 10.6.8.
And if your computer is a Power PC (G4/G5, etc) and has no
Core2Duo kind of CPU -- See "About this Mac" in apple menu
to disclose the general info about your Mac. Also you can see
even more by clicking on "More Info" when looking in there...
If it isn't an Intel-based Mac, it can't run a system past 10.5.8.
Hopefully this helps.
Good luck & happy computing!

Hello I bought my wife a new MacBook Pro, in setting it up for her, I took her Time Machine external drive to migrate onto the new machine but her old MBP not only was on 10.6, it was my old machine which I was still Administrator for. i plugged in the

Hello
I bought my wife a new MacBook Pro, in setting it up for her, I took her Time Machine external drive to migrate onto the new machine but her old MBP not only was on 10.6, it was my old machine which I was still Administrator for.
i plugged in the external drive to start the migration process after entering her name and username from the old machine which gave me the options on transferring the old data over.
I also unchecked the Administrative end that had my info hoping that ONLY her data, files, etc., would be the ones sent over to her new machine which I wanted her to be the ONLY Administrator for. All went like clockwork until the restart.
Normally the screen should show the username and only need the password but both entries were blank, as in ‘Other’ sign in option available only. I entered her name and password, nothing….used her username and password, nothing. Used my old Administrator name and password, NOTHING!
I tried defaulting to factory settings from the Restore feature but it directs me to notify Apple. I tried in Terminal to change the password, nothing. I tried to boot from MY external drive and it doesn’t recognize it. I tried to even use my external drive which actually has the Mavericks upgrade, nothing!
Basically I can only get the startup screen which isn’t accepting the username/password or the Restore feature which doesn’t offer any options helpful!
Please, how do I start from scratch and start over here? Or simply change the Administrator name and password so I can proceed with everything thats already on there? I wish I could even boot from another drive but no luck on anything!

First, on the old machine, make your wife's account an admin one. Log into it and delete yours. Then, update the TM backup. Finally, use Internet recovery mode, ⌘⌥R, erase the HD, and restore the OS. One first boot, follow the steps outlined in Pondini's Setup New Mac guide.

I want to connect an Airport Express via WiFi to my internet connection and then connect its LAN port to the WAN port of a Time Capsule. Will then any device connected to the time capsule wirelessly be also connected to the internet?

Background is I can't hook up my time capsule directly to my internet connection via network cable. I tried to extend the network via Wifi, but that did not work. At the moment I have two wireless networks, one with internet connection and another one with my time capsule. So to use time machine I have to change my network all the time.
Can I buy an Airport Express, use is as a client to my internet connection wifi and provide that connection via network cable to my time capsule and all it's wifi clients?

The AirPort Express will connect to your existing wireless network if the network is using WPA2 Personal or WPA/WPA2 Personal wireless security settings.
So, it can join the network as a client and then provide an Ethernet signal to your Time Capsule.
Be sure to configure the Time Capsule to operate in Bridge Mode so that it will be operating on the same network.

I have an Airport Extreme, I want to replace it with a Time Capsule. I swapped my cables to the new TC, unplugged both Cox Cable modem and Airport Extreme. Started up by plugging A/C power for Cox Cable modem, then power to TC. Result is blinking amber

Similar Messages

Maybe you are looking for