I have an Airport Extreme wireless router & I can not connect my Kindle.

I have an Airport Extreme wireless router & I can not connect my Kindle. Also, my password will not work when a visitor uses it for a laptop (even a Mac) or any other device that uses the internet. It says the password is incorrect. I easily connected a Kindle last year, but I got a new one & now I can not connect wirelessly. I see no tab to create a guest network. I do not mind giving my password to visitors, but that does not work.

If you temporarily disable wireless encryption on your 802.11n AirPort Extreme Base Station (AEBSn), can the Kindle connect to the router and gain access to the Internet now? If so, then I would suggest that you reconfigure the AEBSn to use "WPA2 Personal" for the Wireless Security setting, and then, try connecting with the Kindle again.
As far as establishing a Guest Network, the AEBSn must not be in bridge mode. That is, it should be the only router in your current network and directly conncted to the Internet modem. If it is, then you would find the Guest Networking option on the AirPort > Guest Networking tab:

Similar Messages

HT4628 I recently transferred my internet service to another state. Have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the i

I recently transferred my internet service to another state.I have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the internet. Any suggestions?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

I have an airport extreme. i am trying to connect a laptop with windows 7 to a wireless printer, with no luck. any ideas?

I have an airport extreme. i am trying to connect a laptop with windows 7 to a wireless printer, with no luck. any ideas?

The problem is not the router.. the issue is the vpn has put your computer in a different IP range with a different gateway. When you turn off the vpn the computer returns to local lan and can print.
Some vpn software allows you to set gateway to use local net instead of remote gateway or access to other webistes or local lan.
Read up the issue.
http://stevejenkins.com/blog/2010/01/using-the-local-default-gateway-with-a-wind ows-vpn-connection/
Cisco vpn client..
https://supportforums.cisco.com/thread/239113
I did not search much.. just grabbed the first article I could find that explains the issue.
The whole point of the vpn is whilst it is connected your computer is NOT part of the Local Lan .. it is part of the Remote LAN via the vpn tunnel.
It is also a security risk using split tunnelling so often it will not be allowed.
Plug the printer directly into the computer via usb or whatever.. Local connection will work.. not local lan.

I have a Airport Extreme with a 1TB external HD connected to it. How can I password protect certain files?

I have a Airport Extreme with a 1TB external HD connected to it. I have it set up so my Macbook Pro and PC's in the house can access it. i have some files that i would like to protect(sensitive personal info.). Is there a way that can be done where as certain folders are password protected? Any advice is appreciated. Thanks!

Would a good workaround be to use disk utility to set up a password protected sparse image, of course being connected directly to the Mac, then connect the drive to the Airport Extreme?
Then, couldn't one use that drive and protected files as normal on the airport? It would just require one extra step of using a Mac to set things up first.
I disconnected my Airport so cannot check it out for myself.
Hugh

How to set up Airport Extreme wireless router

Hello. I am trying to connect my Airport Extreme base station to my phone line connection.
From the phone line there is an ADSL filter which has a RJ11 output and phone modem. I purchased a RJ11 to RJ45 (Ethernet) and tried to plug into my router. The airport extreme doesn't recognise anything being plugged in!
My ISP is TalkTalk. This is a secondary router. Other one is a Netgear using downstairs phone modem.
Any help would be grately appreciated
Sam

Thanks for your answer.
So if i buy a DSL modem and go Phone line > DSL modem > Airport Extreme > Mac / WiFi - will that work?
Do you recommend any specific DSL modems that dont use USB (or USB...)?
Thanks

I have an Airport Extreme and want to extend my connection and have a printer connected to the express. How do I do this??

I have been looking on all the forums to see how this can be done. I would like to do this wirelessly as the Extreme is on the first level and express in the office with the printer. Could someone please walk me through the steps to do this. Can I connect my speakers wirelessly to the express as well?
Thanks

I have been looking on all the forums to see how this can be done. I would like to do this wirelessly as the Extreme is on the first level and express in the office with the printer. Could someone please walk me through the steps to do this.
Please check out the following Apple Support article for details on how to configure your AirPort for an extended network.
Can I connect my speakers wirelessly to the express as well?
No, not by a wireless connection. They would need to be connected to the AirPort Express' audio port using an appropriate (analog or digital optical) cable as required by your speakers.

Airport Extreme dropping out and can't connect PC anymore

Hello
Suddenly, a couple of weeks ago, my internet connection dropped in the middle of surfing. I couldn't reconnect, Airport was only seeing the base station spasmodically and when I did try to connect I was being asked for a password which wasn't recognised. Hours later I called the support line and was advised to do a hard reset which I did, new name, same password. Now I'm reconnected most of the time, but it has dropped out a few times and the signal seems generally weaker. Something's not right.
I had not at that point done the July 1st update so it's not to do with that. I haven't a clue why it suddenly started playing up so strangely. (Though I have noticed a new unsecured wireless network in range and wondered if someone was 'hacking')
My main problem is that my business partner, who connects through a pc here (who remained connected incidentally when I first lost the connection) and continued to be able to connect until I did the hard reset. Now I can't connect that pc to the airport extreme. It sees it but gives an error message saying it's out of range and refresh the list when I try to connect. I fiddled about for hours. I've forgotten how the pc was set up in the first place and I'm going nuts. Can anyone help.
Thanks
Helen

Disappointed not to see any help on this one.
If it helps anyone out there to help me, I just uploaded the Airport Utility Software to the pc, typed in base station ID and password. Error message, check network connections. No help.
Try to connect the pc again the usual way from the list of available networks, it asks for password, I use it, then it says it needs to be 5 or 10 ASCII characters or 20 hexadecimal.
What I don't understand is that everything was working fine on both machines until two weeks ago when my base station went into spasm, dropped me but happy with pc, when I did the hard reset, keeps me, won't allow pc to connect.
I just don't know what to do now. Of course I suppose I could always make a call and pay £35 to have an apple technician tell me why their hardware suddenly screwed up for no apparent reason.
Seriously frustrated
Anyone?

New router and can not connect wirelessly

Installed a new router that changed my security from a WEP to a WPA2. I have connected to the printer(7410) through ethernet cable and changed the security settings but the printer will not connect to my router. I am currently printing by ethernet cable hooked directly into the router. When i try to use the printer interface to cinnect to router the only option that comes up is WEP.
Any ideas?
This question was solved.
View Solution.

The printer will support WPA, but not WPA2. It may have previously been connected to WEP and is expecting that. Let's reset it:
From the front of hte printer: Setup > Network > Restore Network Defaults. Now try the Wireless Setup Wizard from that same Network menu.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

No Problem hooking up Vista laptop with WRT110 Wireless Router but can not get XP laptop to see it

I purchased a WRT110 Linksys wireless router this afternoon and had no problem configuring it for my wired desktp and my wireless Vista laptop, but my Acer XP wireless laptop will not even see the network. I have tried WEP, WAP, and no security, but I can see the neighbors routers but I can not see mine. My XP laptop is an Acer 3680-2574 with a Broadcom 802.11g network adapter.

Is the SSID enabled on the router ?
What is the firmware on the router ?
Click here to check the updated list of firmwares.
For information on upgrading the firmware on the linksys routers :
http://linksysfirmwares.googlepages.com/upgradingfirmware
For information on wireless security :
http://linksysfirmwares.googlepages.com/wirelesssecurity
C | EH
linksyshelp.blogspot.com

HT3500 I have a new epson wireless printer but can not get my Mac laptop to print to it even after doing the installations. What do I need to do

I have a new epson wireless printer but cnannot get my Mac laptop to print to it. Any suggestions

Can you find your printer in Print & Fax?

My airport extreme is working but will not connect to my mac pro

my airport extreme is working and all other devices connect except my mac pro computer, How do I resolve this problem?

Hi fdrussell,
Welcome to the Support Communities! Were your Airport Extreme and Mac Pro communicating earlier? If so, what changed?
First try shutting down the computer, and recycling the power to the Airport Extreme. Then start the Mac Pro and see if that resolves the issue.
If needed, perform a Hard reset of the Airport Extreme:
Resetting an AirPort base station FAQ - Apple Support
http://support.apple.com/en-us/HT3728
I hope this information helps ....
- Judy

Wireless router wrt310N can't connect to the ps3

I just bought the wireless router wrt310n yesterday got everything setup and installed. My PC works fine with the ethernet cable plugged directly into the router from my modem. But my router does not detect the connection to ps3. When I do the connection test on my ps3 it says exchanging key then connection failed!. Please help me open ports or resolve this issue. Thanks.

I bought the same router for my ps3 i'm using it wired but when i hooked up my psp i had the security on wep2 personal, make sure the passphrase it typed correct it's case sensitive,also check your wireless broadcast and make sure it is in manual and b and g mixed and not broadcasting n since the ps3 is wireless g.

Airport reads full signal, but can not connect to internet

Hi everyone,
I have a new powerbook that I'm trying to connect to a home network which is set up with a cable modem and a wireless linksys router. The airport reads that it has full signal from the "linksys" wireless network, however I can not get on the internet through the signal. When I connect the computer directly through the the ethernet port, it works fine. I've taken the computer to another location with the same cable modem and wireless linksys router setup, and it worked fine through the wireless. I've actually had this problem quite a few times with various wireless networks (it connects directly, but not through the full signal that reads on the airport), and I was wondering if there are some setting that need to be changed or checked for certain wireless networks. Any help would be great. Thanks,
Sofi

I'm sorry I think this makes thing harder, but I have no idea. It's actually a friend's network so I can't check at the moment. I know there is no password to the network and that they have two pcs running fine wirelessly. Is there a way I can check these settings and see what's going on?

We have a new mac book and i can not connect to the internet

I am setting up a new mac book and the wireless is not connecting to the internet. I have gone to airport express in utilities but it does not give me any options for set up. I have a mac and we use wireless with a dsl modem.

OS X: How to troubleshoot Wi-Fi connectivity
If your Mac is new you should call AppleCare. Telephone support is free for the first 90 days of ownership.

I have an iPod that when I try to update the Apps that are shown to need update-ding and when I indicated to have them updated I get a message "can not connect to App store". The ipod has been updateing until recently. I came still down load new App and

I submitted my question but ran out of room in the box. I can still down load new Apps to my iPod touch AND update them but CAN NOT update the older Apps. that was on the iPod before the problem.
I have been to Three Apple Service Center stores - In Tulsa OK, Oklahoma City OK, Tacoma WA and NO ONE could tell me what is the problem OR what to do to correct it. The Tech then tells me to get hold of the main Apple Service Center number. I tell them I already have and they still recommend going to them.
I have erased all information and started over as a new iPod Touch but the problem persists.
I have called the Apple Service number and they tell me to do everything that the the Tech's at the Apple Service center stores tried to do but DID NOT work.
After I spend a lot of time on the phone, I get told to make an appointment at a Apple Service center store so they can physically have hands on assistance. Come on folks I have already done that and they were of no help. When I say that, I get told that may be the only way I can get the problem resolved.
Surely there is someone out there that knows something about what is happening OR not happening with my iPod and provide a solution.
Thank You for your concideration

I submitted my question but ran out of room in the box. I can still down load new Apps to my iPod touch AND update them but CAN NOT update the older Apps. that was on the iPod before the problem.
I have been to Three Apple Service Center stores - In Tulsa OK, Oklahoma City OK, Tacoma WA and NO ONE could tell me what is the problem OR what to do to correct it. The Tech then tells me to get hold of the main Apple Service Center number. I tell them I already have and they still recommend going to them.
I have erased all information and started over as a new iPod Touch but the problem persists.
I have called the Apple Service number and they tell me to do everything that the the Tech's at the Apple Service center stores tried to do but DID NOT work.
After I spend a lot of time on the phone, I get told to make an appointment at a Apple Service center store so they can physically have hands on assistance. Come on folks I have already done that and they were of no help. When I say that, I get told that may be the only way I can get the problem resolved.
Surely there is someone out there that knows something about what is happening OR not happening with my iPod and provide a solution.
Thank You for your concideration

I have an Airport Extreme wireless router & I can not connect my Kindle.

Similar Messages

Maybe you are looking for