I have attempted to download with Bootcamp the Windows 7 drivers but the dowload will not progress past 25%!
I have attempted to download with Bootcamp the Windows 7 drivers but the dowload will not progress past 25%!
Is there someone that can assist me with this issue?
:>/
You may have better luck posting in the Boot Camp forum, that is where the Boot Camp and MS Windows guru's tend to hang out.
Similar Messages
-
Lee3
May 25, 2012 5:36 AM
I have attempted to download with Bootcamp the Windows 7 drivers but the dowload will not progress past 25%!
Is there someone that can assist me with this issue?
:>/How long did you wait for the download to run? The last time I downloaded the Windows support files for Boot Camp, it was going very slowly, so I swapped away to another task. Several minutes later I came back and it had moved a little, but not much, so I went on with other things. When I got back to it several hours later, the download had completed. Perhaps you just need to let it go overnight to perform the downloads...
-
I have a Macbook and I left it unplugged. It started up slowly when I plugged it in again, but it seemed fine. Once it started charging I shut it down so it would be easier, but now it will not go past the grey screen with the apple. What do I do?
I have Snow leopard on my computer, and I tried to do a hard restart as an article suggested, but it did not work. I also tried cleaning out the PRAM.
The only things I did last night:
-cleaned the history of Firefox out, including cookies
-let it unplugged all night
-plugged it back in the morning, it took a long time to figure itself out, but eventually the time was correct and I got on the internet for a bit
-shutdown the computer since I was going out and thought it would help the computer charge
-came back, tried to turn it on, and found that it would not go past the grey screen the apple on it and the spinning wheel even though I left it for 20 minutes or more
-tried turning it off and on to no availBefore doing a reinstall, which may not be needed at this point,
Try using Disk Utility to do a Disk Repair, as shown in this link, while booted up on your install disk.
You could have some directory corruption. Let us know what errors Disk Repair reports and if DU was able to repair them. This could just be a start in repairs and you may need a better utility to finish the job.
Then Repair Permissions.
No need to report any Permissions errors........we all get them.
DALE -
Tried downloading Mavericks this morning and it froze. I deleted where it started the download and I tried to restart it but now it will not let me start the download. just wants to go to install but there is nothing there to install.
Hello Curtis,
Thank you for the details of the issue you are experiencing when trying to downlaod Mavericks. I recommend emptying your trash and restarting your computer. Once you have done that, navigat the the Purchased tab of the Mac App Store and try downloading Mavericks again:
Mac App Store: Finding your purchased apps
http://support.apple.com/kb/HT4483
Thank you for using Apple Support Communities.
Best,
Sheila M. -
I want to change my Apple ID to what I have as my rescue ID. The system will not let me.Is there a way to do this?
You'll need to change/remove your rescue email address first :
1. Navigate to appleid.apple.com using your web browser.
2. Click "Manage your account"
3. When prompted, sign in using your Apple ID and password.
4. Click Password & Security
5. You'll be asked to answer 2 of your 3 security questions before you can make any modifications. If you are unable to remember your answers, you can choose to send an email to your rescue email to reset your security questions.
6. After you've validated your identity by correctly answering your security questions, click Edit to the right of your rescue email address.
7. Once you've finished editing your rescue email address, click the Save button directly below the email field. -
After upgrading to iOS5 I can not set the store to auto download anything. The buttons will not stay in the ON position. Any thoughts?
I experienced this one time and this is what I did and it worked for me. You can try it as well and see of it works for you.
Settings>Store>Apple ID - tap on your ID and sign out. Restart your iPad. Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
Go back to Settings>Store>Sign In. Then go to automatic downloads and try again. -
When I try to install WinXP using bootcamp, the iMac will not recognize the CD after it has already read all the information and is ready to begin installation. What is the problem?
If your on 10.6.8 like you should be for security/stability updates, somewhere along the line a later Bootcamp version was issued and only supports Win 7.
You can read my post here for a alternative solution, running a virtual machine software
https://discussions.apple.com/thread/3772839?tstart=0 -
My iPad will not progress past the home screen, and my computer doesn't allow me to download my data from it. What do I do? I wanted to try to restore it, but I don't want to lose my "stuff".
First, try a system reset. It cures many ills and it's quick, easy and harmless...
Hold down the on/off switch and the Home button simultaneously until you see the Apple logo. Ignore the "Slide to power off" text if it appears. You will not lose any apps, data, music, movies, settings, etc.
If the Reset doesn't work, try a Restore. Note that it's nowhere near as quick as a Reset. It could take well over an hour! Connect via cable to the computer that you use for sync. From iTunes, select the iPad/iPod and then select the Summary tab. Follow directions for Restore and be sure to say "yes" to the backup. You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod. Again, say "yes."
At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod. As before, say "yes." Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time. If that happens, only the apps that are part of the IOS will appear on your device. Corrective action is simple - choose manual "Sync" from the bottom right of iTunes.
If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose your "stuff" with Recovery Mode. -
I tried to update software on my i phone 4s and the phone will not restart past the apple logo? The logo keeps flashing up but wont go further.. please help!
Place the phone in recovery or DFU mode (search Google) and restore.
-
Can anyone help? My wireless connection is working on both my iphone4S and my ipad2, but my Imac will not connect to the network.
First run Software Update to make sure your iMac is up-to-date.
Even though things are working OK on other devices there may still be issues with your modem or router so it's best to start there. Locate the manuals on both devices and reset each. Do the modem first then the router. Next make sure the router has up-to-date firmware. If the problem continues after updating resetting and updating both devices then download and install iStumbler and let it run for about 30 minutes. iStumbler will scan your area for the Wi-Fi networks being used, pay attention to the channels each network is set to. Most routers are pre-set to channels 5 or 6 and if you are in a congested area and all the routers are set for channel 5 or 6 then you can see where there might be a problem. Set your router's channel to one not being used in your area, you have at least 14 channels to choose from. Also check to see if your router is using 802.11n, if it's not then it would be wise to upgrade the router to a faster device.
Next is if you are still having issues the problem could be your ISP's DNS settings. If you want to learn about DNS please read CNET's DNS Article and MacWorld's DNS Troubleshooting . Then use the instructions below to reset the DNS settings:
1. System preferences
2. Network
3. Click Advanced
4. Click DNS tab
5. Click + sign
6. Add 208.67.222.222
7. Click + sign
8. Add 208.67.220.220
9. Click OK.
10. Exit System Preferences -
My bluetooth keyboard (Macnus brand - bought recently in Thailand)(similar to Mac small keyboard) will pair with my iPad using code 8310,and is recognized by my iMac but will not pair?
There are very scant instructions with the keyboard and no mention of any code (the code was prompted by my iPad).
I have followed the instructions but it still will not pair with my iMac!
Can anyone help please?
My iMac is 20 inch Mid 2007 OSX10.9.1 4GB RAMHi All, thank you for you suggestions. I have been unable to find any website for the maker, but have looked at several Thai/cambodian sites incl <http://www.buycoms.com/Article/8435/index.asp> which mentions the keyboard being suitable for tablet or windows. No mention of iMac! although the box is branded to indicate Mac compatable.
I'm thinking that maybe it just will not pair with an iMac.
Ill keep looking for the maker website, which might come on later in the future? maybe?
thanks again. -
Hi
We have a Windows 2012 server with Exchange 2013, all is working fine except now i am getting issues with the backup.
'Exchange - The application will not be available for recovery from this backup. the consistency check failed for the component Microsoft Exchange Server'
I have checked the database all is fine, i have created a new db and move all mailbox;s over and then removed the old db, i have enabled circular logging and then disabled it, it seems no matter what i do i cannot get a full backup!
i did have to restore the server once and the backups still worked for about 4 days after that and then stopped, i have also tried to remove and re add the backup role!
i am stumped, any advice would be great!Hi
Ok, i created a test db and tried to back it up right away, it failed, i did not add any mailbox's to it either. i got quite a few events in the windows logs, as well as the same event above i got the following:
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2038
Task Category: Exchange VSS Writer
Level: Warning
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Microsoft Exchange VSS Writer backup failed. No log files were truncated. Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9. Database 4843b37c-7b3c-42b2-8b57-1393615c2c15.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="32772">2038</EventID>
<Level>3</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261645</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>4843b37c-7b3c-42b2-8b57-1393615c2c15</Data>
</EventData>
</Event>
AND
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2038
Task Category: Exchange VSS Writer
Level: Warning
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Microsoft Exchange VSS Writer backup failed. No log files were truncated. Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9. Database db5826f3-1029-4219-ad80-441a0e94537a.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="32772">2038</EventID>
<Level>3</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261646</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>db5826f3-1029-4219-ad80-441a0e94537a</Data>
</EventData>
</Event>
and
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2034
Task Category: Exchange VSS Writer
Level: Error
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
The Microsoft Exchange Replication service VSS Writer (Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9) failed with error FFFFFFFC when processing the backup completion event.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="49156">2034</EventID>
<Level>2</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261649</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>FFFFFFFC</Data>
</EventData>
</Event>
and
Log Name: Application
Source: SPP
Date: 21/01/2013 10:16:30
Event ID: 16389
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Writer Microsoft Exchange Writer experienced retryable error during shadow copy creation. Retrying... More info: .
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="SPP" />
<EventID Qualifiers="0">16389</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261650</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>Microsoft Exchange Writer</Data>
<Data>
</Data>
<Data>The writer experienced a transient error. If the backup process is retried, the error may not reoccur. (0x800423F3)</Data>
<Data>
</Data>
<Binary>00000000A5120000981200000000000042BEB7C511CAC619E59C92030000000000000000</Binary>
</EventData>
</Event> -
I have installed max os x Lion on my MacBook pro, but now safari Will not open any internet pages
I have installed mountain Lion on my MacBook pro , but now safari Will not open any internet pages??
Try this:
1. Go to Safari > Preferences > Extensions
Disable any extensions.
Restart Safari and test. If that doesn't work, try this:
2. Create a new location and renew the DHCP lease. See here for the procedure:
http://osxdaily.com/2012/08/02/fix-os-x-mountain-lion-wireless-connection-proble ms/ -
Just tried to upgrade to SnowLeopard with newly purchased software disc. iLife failed to download and when I tried to restart the computer, it will not do so--just get a grey screen with the lines going around and around. Any ideas about how to get it to start?
Mac Pro - Mid 2010
Processor 2 x 2.66 GHz 6-Core Intel Xeon
Memory 8 GB 1333 MHz DDR3 ECC
Graphics ATI Radeon HD 5870 1024 MB
Software Mac OS X Lion 10.7.2 (11C74)
This is a brand new machine that I just purchased from Apple. It was delivered yesterday
The old computer is an old PowerMac G5, but my OS X install disc is a retail version of 10.5.
I also tried the OS X 10.5 install disc that came with my MacBook Pro (2.6 Ghz Intel Core 2 Dual).
Same issue - nothing but a grey screen when the system tries to boot from the DVD -
my somewhat old imac osx 10.5.8 with iphoto '08 will not read my RAW files from my new Nikon D800 camera - a new model on the market( 5 months or so). How can I get iphoto to read my RAW files?
iPhoto 08 would not read RAW files from that new a camera. You need to upgrade so you can get more up-to-date version of OS X and iPhoto. Another possiblity is see if iPhoto 11 will run on 10.5.8, if so you should update. You can also attempt to run Software Update and see if it finds a newer release of iPhoto 08 that supports newer RAW formats.
Maybe you are looking for
-
Why can't I open .webloc files on my iMac 10.6.8?
I want to open files which have the extension <.webloc>. The file reaches my iMac but I can't read it, it stays blank and just sits on my desktop. I'm not sure but I think when I open 'Spotify' that has a <.webloc.> extension!
-
Remove gmail from blackberry 9300
Hi, Can anybody tell me how to remove my gmail account from my BB? I need a step by step instruction please Thanks, John Solved! Go to Solution.
-
Using System::ErrorDescription in Insert statement
Hello, I want to insert System::ErrorDescription to store the error in the customized log table. When I use the following statement, it does not insert anything. What am i doing wrong. Please advice. create table dbo.load_err(load_err_id integer(PK),
-
Dear Sir My cleint requirements. 1 For contractor issues as followed a) Chargeable to contractors b) Loan - returnable basis c) Free for contractors. 2 Material reconciliation with contractor steel, at their location 3 Consignment deta
-
All - I'm currently working on a program which will solve Linear Programming problems. To do so, I would like to use the COIN-OR libraries which are implemented in C++ and I've decided to use JNI to do so. I've successfully compilied my java app, cre