I have changed my location from korea to pakistan and now my iphine 4 is not working?

i have shifted in pakistan but my i phone is not working.
its iphone 4 and version 6.01

Very vague.
In what way is it "not working"?

Similar Messages

HT201303 I have changed my country from India to Oman. Now when I try to download some application, the message "you should shift to Omani store for purchase". In itune it shows, you can only purchase from Omani Store". How to correct this contradiction.

Hi
I have changed my country from India to Oman. Now when i try to update or download anyu application, the message," Your account is not valid for use in Indian Store. You must switch to the Omani Store before purchaseing" comes.
In Itune account details, the country is shown as Oman and payment details are also OK thru Oman based bank's Visa card.
Now the problem is that I cannot update any of my applications or download any new applications.
Could you please help.
Regards,
Karingada

Contact iTunes Customer Service and request assistance
Use this Link > Apple Support iTunes Store Contact

I have just changed internet providers from BT to Virgin, and now my iTunes doesn't show any of my airport express devices.

I have just changed internet providers from BT to Virgin, and now my iTunes doesn't show any of my airport express devices. I assume that I have to reconfigure them to the the new wireless but how do I do this frmo my PC? Thanks

I would recommend that you start by performing a "factory default" reset on each of your AirPort Express base stations. Once completed, you can use the following Apple Support article to configure each base station for streaming.

I plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

i plugged in my ipod and now i get the error message: Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled" - i have a MAcBook pro and now my USB ports do not work - can anyone help me ???

Sometimes you have to reset the SMC two or three times for it to work, don't know why. I've seen that error message before and 100% of the time it was fixed with an SMC reset. I suppose it's possible that your keyboard or mouse IS drawing too much power, do you have access to another you could try?

Ipad displays "ipad is disabled connect to itunes", I have tried putting the ipad into recovery mode and then restoring but that does not work. I have also tried doing a hard reset of the ipad and that does not work either. Any ideas?

Ipad displays “ipad is disabled connect to itunes”, I have tried putting the ipad into recovery mode and then restoring but that does not work. I have also tried doing a hard reset of the ipad and that does not work either. Any ideas?
My son let one of his friends use his ipad. The next time he tired to use it he could not get it unlocked, I tired to unlock it but it kept telling me that I had the wrong pass code. With out me knowing my son continued to tire until it completely disabled it self.

How can I unlock my iPad if I forgot the passcode?
http://www.everymac.com/systems/apple/ipad/ipad-troubleshooting-repair-faq/ipad- how-to-unlock-open-forgot-code-passcode-password-login.html
iOS: Device disabled after entering wrong passcode
http://support.apple.com/kb/ht1212
How can I unlock my iPad if I forgot the passcode?
http://tinyurl.com/7ndy8tb
How to Reset a Forgotten Password for an iOS Device
http://www.wikihow.com/Reset-a-Forgotten-Password-for-an-iOS-Device
Using iPhone/iPad Recovery Mode
http://ipod.about.com/od/iphonetroubleshooting/a/Iphone-Recovery-Mode.htm
You may have to do this several times.
Saw this solution on another post about an iPad in a school environment. Might work on your iPad so you won't lose everything.
~~~~~~~~~~~~~
‘iPad is disabled’ fix without resetting using iTunes
Today I met my match with an iPad that had a passcode entered too many times, resulting in it displaying the message ‘iPad is disabled – Connect to iTunes’. This was a student iPad and since they use Notability for most of their work there was a chance that her files were not all backed up to the cloud. I really wanted to just re-activate the iPad instead of totally resetting it back to our default image.
I reached out to my PLN on Twitter and had some help from a few people through retweets and a couple of clarification tweets. I love that so many are willing to help out so quickly. Through this I also learned that I look like Lt. Riker from Star Trek (thanks @FillineMachine).
Through some trial and error (and a little sheer luck), I was able to reactivate the iPad without loosing any data. Note, this will only work on the computer it last synced with. Here’s how:
1. Configurator is useless in reactivating a locked iPad. You will only be able to completely reformat the iPad using Configurator. If that’s ok with you, go for it – otherwise don’t waste your time trying to figure it out.
2. Open iTunes with the iPad disconnected.
3. Connect the iPad to the computer and wait for it to show up in the devices section in iTunes.
4. Click on the iPad name when it appears and you will be given the option to restore a backup or setup as a new iPad (since it is locked).
5. Click ‘Setup as new iPad’ and then click restore.
6. The iPad will start backing up before it does the full restore and sync. CANCEL THE BACKUP IMMEDIATELY. You do this by clicking the small x in the status window in iTunes.
7. When the backup cancels, it immediately starts syncing – cancel this as well using the same small x in the iTunes status window.
8. The first stage in the restore process unlocks the iPad, you are basically just canceling out the restore process as soon as it reactivates the iPad.
If done correctly, you will experience no data loss and the result will be a reactivated iPad. I have now tried this with about 5 iPads that were locked identically by students and each time it worked like a charm.
~~~~~~~~~~~~~
Try it and good luck. You have nothing more to lose if it doesn't work for you.
 Cheers, Tom

I have recently upgraded my iMac Intel G5 iSight to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old sys parts

I have recently upgraded my iMac Intel G5 iSight (iMac5,1) to OS 10.6.8 and now the internal mic does not work with skype or facebook. I can here static when playing back clips. Do I need to update firmware or reload old system parts. I have zapped PRAM. The blue indicator in system audio panel will appear for a second as I slide the bar for internal mic but then it disappears. Is there a fix?

The sound seems very faint but can here static on playback.

After my iphone4S update to 7.0.6, it have a problem that keep searching network then no service show on display. Can't call. I have try check sim card, reset network settings, and restore my iphone. Still not working at all. Need help please.

After my iphone4S update to 7.0.6, it have a problem that keep searching network then no service show on display. Can't call. I have try check sim card, reset network settings, and restore my iphone. Still not working at all. Need help please.Urgent.TQ

Izit software or hardware? Confuse:(
Only can use wifi now.
Any way thanks guys for ur suggestion:) amishcake and simes

I just switched from Outlook to Mail and now the sent messages are not being displayed. Help, please.

I just switched from Outlook to Mail and now the sent messages are not being displayed. Help, please.

Back up all data. Rebuild the mailbox.

I have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

i have iphone 4 and i used it for a one and half years.i used it in sri lanka and doha qatar also..,recently i update it i.o.s 7, then it was working.after i.o.s 7.0.3 came i again updeted it and now my phone network is not working.now phone is locked.pls help.

I am seeing if I can get another battery even though I do not believe that is the issue. It keeps giving me vdd_under which I believe is under voltage, maybe it is just a faulty battery? It charges up like normal and functions normal (when plugged in, or above 90%) but it gives under voltage warnings and shuts down when in heavy use (using camera or going back and forth to imessage). When just sitting idle it doesn't seem to turn off until that 55-60% mark. It may just be a faulty battery because I feel I installed all of the other cables correctly when replacing the screen, and I don't think those connections should affect the battery anyway except for maybe the logic board cable (the 2nd cable to be unplugged after the battery cable) I guess I could clean that out as well with isopropyl just in case.
Any other suggestions would be helpful... and I will get back to you if a new battery helps. Thanks!

Have just downloaded iTunes 10.5.2.(11) onto Mac Book Pro and now the earphones port does not work. Any suggestions? Annie H

Have just down loaded iTUnes 10.5.2.(11) onto MacBook Pro and now the earphone port is not working. Any suggestions. Annie H

My System Preferences>Soundoutput screen does not have the "Use audio port for" field.
Does your MBP have two separate audio ports - one for line-in and one output port? Then you wan't see that selector.
but the port has started to work again....Reason???
Perhaps there was dirt or something in the jack and the contact was bad.
(or you accidentally put the plug into the line-in jack instead into the audio-out; that happened to me once ).
Regards
Léonie

I was prompted to change batteries. I did and now my track pad is not working

I was prompted to change batteries on my track pad. I did and now the track pad is not working.

Did you replace your battery with one of as good quality as that you are disposing of. Does the indicaror light show when you start up.

I have changed my internet connection to Huawei HG8245 modem wireless modem my Air Play not working any more

I have apple TV 3rd generation it use to work fine through the previous modem(THOMSON TG585 v7)
I have changed my internet connection now using Huawei HG8245 modem.
At the moment There is internet connection in the apple TV I can manage only through the apple remote. But I can’t AIR PLAY or mirroring from iphone ipad and my MacBook Pro.
I can see the AIR Play but I can’t play any music or video in the apple TV. Also I am sure I have activated the home sharing in I tunes/Remote app/apple TV
Personally I think because the connection setting,but I do not know how to fix it can someone advise please?

MOG,
I have a similar problem with this HG8245, but I can't even see the airplay icon in my iOS devices nor my MB Pro. However, I discover by accident that it works very well if I connect the ATV through the wifi interface (tested with my iPhone 4 and iPad 3Gen both w/iOS 6.0.1, and my MB Pro w/OS X 10.8.2). But as soon as I connect the ATV through the ethernet port, it disappears from all my devices.
So my guess is that there is some issue (i.e. undocumented filtering) between the wifi and the ethernet interfaces. I have reviewed the HG8245 configuration but I haven't found how to solve this. Have you figured out how to solve it? I will try to use some port scanner to see if there is some difference im using the wifi and the ethernet ports and will post the findings.

I have an iPhone 4S I have done the recent update 6.1 and now my App Store is not working when I go into the feature tab I get an error " too many HTTP redirects" how do I fix this ? The other tabs are working and it is working on my iPad also

I am having a problem getting into the App Store on my iPhone since the recent update, I have a 4s and it appears the feature tab is not working. When I try to go into the feature tab in the App Store I get a message "too many HTTP redirects" ?... Does anyone now hoe to fix this issue, the other tabs are working okay and everything is working on my iPad ?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Transfer account from old MBP to new one and now my account password does not work.

I trasferred my account from one MPB to a new one using targeted disk method. I left my desk while it finished and came back to a registration page. I registered and the system rebooted. Now I see my login details but the password form my old Mac fails. The hint it gives me also seems to be bogus becaues I've tried many variations of the hint and they also do not work.
I'm submitting this from my original MBP and had not problem using my old password logging in to it. Why didn't my password transfer properly and now how do I fix my new MBP?
I made sure duing the transfer process to select everything for transfer -- accounts, applications, etc. All check boxes were checked.

AKAspuds wrote:
I trasferred my account from one MPB to a new one using targeted disk method. I left my desk while it finished and came back to a registration page. I registered and the system rebooted. Now I see my login details but the password form my old Mac fails. The hint it gives me also seems to be bogus becaues I've tried many variations of the hint and they also do not work.
I'm submitting this from my original MBP and had not problem using my old password logging in to it. Why didn't my password transfer properly and now how do I fix my new MBP?
I made sure duing the transfer process to select everything for transfer -- accounts, applications, etc. All check boxes were checked.
So now you have 2 accounts, logout of this one and in to the other.

I recently changed the password for my home network and now my MP495 printer will not connect.

Hi, First time caller, long time listener............
I am running Win 7 on all of the pcs in the house with an Android or two as well. I had to change the pw for my linksys router this past weekend and I noticed today that I can not get on as the "printer is offline". I have done the obvious cycling of pcs , router and printer. I have also tried checking / unchecking the use printer offline. Do I need to redownload the drivers and attach the printer by usb and reinstall it? Its been a while since I installed it and I can't remember if it needed a password to connect or not.
Thank you, I appreciate your time.

Hi Trilo,
Since you changed the password to your wireless router, you will need to reinstall the drivers on your computer to reconnect the printer to your network. Prior to reinstalling, you will want to ensure that the wireless LAN setting on the printer is enabled. To do this, press the Maintenance button on the printer (looks like a pair of pliers and a screwdriver) repeatedly until the symbol that looks like "G" appears in the LCD, then press the <COLOR> button to enable wireless LAN.
Once the wireless LAN has been enabled, please click here to go to the DRIVERS AND SOFTWARE page for the PIXMA MP495. Once on the initial download page for your model, please do the following:
1. Verify that the operating system detected in the "OPERATING SYSTEM" drop-down menu is correct, and if it is not, please click the drop-down menu to select your operating system.
2. Next, please click on the red arrow next to the "RECOMMENDED FOR YOU" section and click the MP drivers file. When you do, a red DOWNLOAD button will appear. Please click on the checkbox below the DOWNLOAD button, then click the red DOWNLOAD button to begin the download. The time for the download process may vary depending on the speed of your Internet connection and the size of the file being downloaded.
Once the file has been downloaded, please double-click on it to reinstall the printer wirelessly.
Hope this helps!
This didn't answer your question or issue? Please call or email us at one of the methods on the Contact Us page for further assistance.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

I have changed my location from korea to pakistan and now my iphine 4 is not working?

Similar Messages

Maybe you are looking for