I have contribute 2, edit has become locked on 1 site other 2 ok

I edit 3 web sites with contribute 2, one site has locked so I am unable to edit, I go to a page to edit, up on the page comes edit multiple pages/frames then below 2 line that are locked first part of each line, Fast Button then code and Postmessage relay it point to me for help as administrator?

Perform a Reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430

Similar Messages

I have an ipad that has been 'locked up' since 10 a.m. central time this morning. It is stuck on the web site that I was looking at

I have an ipad that has been 'locked up' since 10 a.m. cent. time this morning! I cannot do anything to get it to shut off or reset. What do I need to do?

First try a Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
If no joy... Try a Restore...
1: Connect the device to Your computer and open iTunes.
2: If the device appears in iTunes, select and click Restore on the Summary pane.
Restoring > http://support.apple.com/kb/HT1414

I have a ipad which has been locked due to the owner claiming it was lost. I have had the serial no. checked and it is not stolen but I can't use it.

i have a ipad which has been locked due to the owner claiming it was lost. I have had the serial no. checked and it is not stolen but I can't use it. I have talked to the owner many times who refuses to give me the password or has no idea what password was used.

Unfortuinately there is nothing that can be done.
If its locked its locked. This is a theft deterrant mechanism.
If you could unlock "stolen" ipads then there would be no purpose for the feature.
You will have to convince the owner you bought it correctly, or accept its no lonnger usable by you until the original owner removes the lock.

HT4623 I have two iPads one has iOS 7.0.4 the other has 5.1.1 have tried to update the 5.1.1 but keep getting message no update available

I have two iPads one has iOS 7.0.4 the other has 5.1.1 have tried to update the 5.1.1 but keep getting message no update available

The first generation iPad can not be upgraded beyond 5.1.1

Over the past week the Mac mail app on my iPad 2 has become locked in vertical orientation and only in the orientation such that the bottom is orientated toward the menu button. Any advice? This is the only app that seems to have been affected.

For the past week or two, my Mac Mail app for my iPad 2 has been stuck in vertical orientation. This is the only app that is similarly affected. Moreover, it will only orient itself such that the bottom is toward the menu button on the iPad. Please advise if you have a solution.

Try closing the Mail app via the taskbar and see if it rotates when you re-open the app : from the home screen (i.e. not with the Mail app 'open' on-screen) double-click the home button to bring up the taskbar, then press and hold any of the apps on the taskbar for a couple of seconds or so until they start shaking, then press the '-' in the top left of the Mail app to close it, and touch any part of the screen above the taskbar so as to stop the shaking and close the taskbar.
If that doesn't work also do a reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.

I have a L7780 that has become completely unresponsive to all of it's buttons.

Display still looks like it is ready to go, and the printer responds to things like opening the scan table, toner door opening, but all of these seem to be automatic and in reality nothing works. Interior scanning light is on. It is also completelly unresponsive over the network. Anyone ever heard of this problem? Help!

* In Firefox 3.6 versions on Windows and Firefox 4 on Windows and Linux it's possible to hide the "Menu Bar" via "View > Toolbars" or via the right-click context menu of a toolbar.
* Press F10 or press and hold the Alt key down to bring up the "Menu Bar" temporarily.
* Go to "View > Toolbars" or right-click the "Menu Bar" or press Alt+V T to select which toolbars to show or hide (click on an entry to toggle the state).
See also:
* [[Menu bar is missing]]
* http://kb.mozillazine.org/Toolbar_customization

I have 2 iMacs, one has a thunderbolt port and the other has a mini display port. Would it be possible to use one as an extension of the other? If so what cable would I need.

Hi,
As the title of the thread says. I have an older iMac with a mini display port and a newer iMac with a thunderbolt port. Would it be possible so that the older iMac is an extension of my new iMac. The reason for this is because logic x can be a abit clustered on one screen.
Thanks

If you'll be using the 2010 iMac as the display, a Mini DisplayPort to Mini DisplayPort cable.
It's not possible to use the 2011 iMac as the display through Target Display mode in that configuration.
(126322)

Iphone 5s become locked with 02

My iphone 5 has become locked with O2. When I contacted O2, they told me that I can't use my three sim in, they told me that iphone5s become locked with the O2 sim, when I told them that I would like to unlock it, they said that apple haven't issued it yet! what can I do?

Nothing
Apple retail stores and Apple On-line UK are the only source
of unlocked iPhones inc iP5 in UK
All others are locked to a carrier
O2 generally offer unlocking 6-12 months after release of a model
might be longer with iP5 as they cannot offer LTE and
may wish to prevent movement to EE who will have LTE spectrum
Unlocking is nothing to do with Apple
Carriers lock the iPhone only they can unlock it

How to enhance the speed of my MacBook Pro. It has become extremely slow!

My MacBook Pro (2011 early edition) has become extremely slow. What needs to be done to enhance its speed!

Things You Can Do To Keep Your Computer From Slowing Down
If your computer seems to be running slower here are some things you can do:
Boot into Safe Mode then repair your hard drive and permissions:
Repair the Hard Drive and Permissions Pre-Lion
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Repair the Hard Drive - Lion
Boot from your Lion Recovery HD. When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Restart your computer normally and see if this has helped any. Next do some maintenance:
Suggestions for OS X Maintenance
For situations Disk Utility cannot handle the best third-party utility is Disk Warrior; DW only fixes problems with the disk directory, but most disk problems are caused by directory corruption; Disk Warrior 4.x is now Intel Mac compatible.
OS X performs certain maintenance functions that are scheduled to occur on a daily, weekly, or monthly period. The maintenance scripts run in the early AM only if the computer is turned on 24/7 (no sleep.) If this isn't the case, then an excellent solution is to download and install a shareware utility such as Macaroni, JAW PseudoAnacron, or Anacron that will automate the maintenance activity regardless of whether the computer is turned off or asleep. Dependence upon third-party utilities to run the periodic maintenance scripts was significantly reduced since Tiger. These utilities have limited or no functionality with Snow Leopard or Lion and should not be installed.
OS X automatically defragments files less than 20 MBs in size, so unless you have a disk full of very large files there's little need for defragmenting the hard drive. As for virus protection there are few if any such animals affecting OS X. You can protect the computer easily using the freeware Open Source virus protection software ClamXAV. Personally I would avoid most commercial anti-virus software because of their potential for causing problems. For more about malware see Macintosh Virus Guide.
I would also recommend downloading a utility such as TinkerTool System, OnyX 2.4.3, or Cocktail 5.1.1 that you can use for periodic maintenance such as removing old log files and archives, clearing caches, etc.
For emergency repairs install the freeware utility Applejack. If you cannot start up in OS X, you may be able to start in single-user mode from which you can run Applejack to do a whole set of repair and maintenance routines from the command line. Note that AppleJack 1.5 is required for Leopard. AppleJack 1.6 is compatible with Snow Leopard. There is no confirmation that this version also works with Lion.
When you install any new system software or updates be sure to repair the hard drive and permissions beforehand.
Get an external Firewire drive at least equal in size to the internal hard drive and make (and maintain) a bootable clone/backup. You can make a bootable clone using the Restore option of Disk Utility. You can also make and maintain clones with good backup software. My personal recommendations are (order is not significant):
Carbon Copy Cloner
Data Backup
Deja Vu
SuperDuper!
SyncTwoFolders
Synk Pro
Synk Standard
Tri-Backup
Visit The XLab FAQs and read the FAQs on maintenance, optimization, virus protection, and backup and restore.
Additional suggestions will be found in Mac maintenance Quick Assist.
Referenced software can be found at CNet Downloads or MacUpdate.
Additional Hints
Be sure you have an adequate amount of RAM installed for the number of applications you run concurrently. Be sure you leave a minimum of 10% of the hard drive's capacity as free space.
Add more RAM. If your computer has less than 2 GBs of RAM and you are using OS X Leopard or later, then you can do with more RAM. Snow Leopard and Lion work much better with 4 GBs of RAM than their system minimums. The more concurrent applications you tend to use the more RAM you should have.
Always maintain at least 15 GBs or 10% of your hard drive's capacity as free space, whichever is greater. OS X is frequently accessing your hard drive, so providing adequate free space will keep things from slowing down.
Check for applications that may be hogging the CPU:
Open Activity Monitor in the Utilities folder. Select All Processes from the Processes dropdown menu. Click twice on the CPU% column header to display in descending order. If you find a process using a large amount of CPU time, then select the process and click on the Quit icon in the toolbar. Click on the Force Quit button to kill the process. See if that helps. Be sure to note the name of the runaway process so you can track down the cause of the problem.
Often this problem occurs because of a corrupted cache or preferences file or an attempt to write to a corrupted log file.

When I open iphoto the following message appears 'Your photo library is either in use by another application or has become unreadable'

when I open iphoto the following message appears 'Your photo library is either in use by another application or has become unreadable'

Reboot you system, if you have not already done so - this should take care of the "in use by another application" part of the message.
If the problem persist you will need to create a new library or to repair your library, or to restore it from your backup.
If you do not yet have any images in your iPhoto Library simply move it to the Trash and hold down the option-key while launching iPhoto again. This will give you the option to create a new iPhoto Library or to pick another one, if you have other libraries.
To fix your current library, or to restore it from backup, if you already have pictures inside that you need to save, see Terence Devlin's posts here:
Re: Why do I keep getting asked to repair my iPhoto library?
Re: when I open iphoto I get an error message that says Your photo library is either in use by another application or has become unreadable,
Regards
Léonie

How do I remove a DVD that has become stuck?

I have an older 17" MacPro with a slot drive and I now have a DVD that has become stuck. It won't stop turning nor will it release to eject it. How do I get it out?

Many options
-dragging and dropping the icon for the CD into your trashcan
- Restart the computer and after the chime press and hold down the left mouse button until the disc ejects.
- Press the Eject button on your keyboard.
- Click on the Eject button in the menubar.
- Press COMMAND-E.
- Open the Terminal application in your Appl/Utilities folder. copy & paste the following:
/usr/bin/drutil eject
If this fails then try this:
- Boot the computer into single-user mode (hold down command - s through the boot process.) At the prompt copy & paste:
/usr/bin/drutil eject
Restart the computer enter reboot at the prompt or shutdown
- restart hold down trackpad button

Firefox has become extremely slow in the recent times

Firefox suddenly has become very slow. It takes too much time to load all websites and even the typed words and scrolling has a great delay in appearing. It becomes unresponsive very often. I tried reinstalling it and even reset it. Its becoming a pain to use this to surf the net. Please do help!!

I also have found that Firefox has become a dog. I've followed one thread that disabled the plugin-container with no help. 20.0.1 can hang for over a minute and actually hog my entire CPU so I can't even start Chrome! I like my FF plug-ins, but the performance problems of FF 20 are becoming intolerable and no one seems to know what the heck! Chrome does not present the problems and I have been visiting and working at the same websites. If many folks are encountering this mess, I suspect that FF is done for. I have actually found that the Android FF is also tending to slow down my smartphone - stall it! I am a few days away from just removing FF from my computing life.

Hello, I have an otter box for my iPhone 4s and recently the rubber schell has become loose and a little flappy. A lot of my friends have told me that the otter box breaks the lock button on the iPhone and sure enough it has happened to me. It's as if the

Hello, I have an otter box for my iPhone 4s and recently the rubber schell has become loose and a little flappy. A lot of my friends have told me that the otter box breaks the lock button on the iPhone and sure enough it has happened to me. It's as if the lock button is frozen in place and won't click down. Can I return this phone for a new one? my biggest fear is that I'll have to go a couple of weeks with out a phone while I wait for my new one.. And with regards to otter boxes, should I stay away from them to prevent future issues like this from happening again?
Thank you for your help!

"Can I return this phone for a new one? "
Do you mean "can I get a new iPhone for free?" Nope.
Do you mean "since Applecare does not cover accidental damage, can I get a replacment iPhone, for around $250?" Yes.

Music on my iPhone has become very difficult to edit since upgrading to 5.0.1. If I simply want to delete some songs, it insists on a complete sync cycle after EACH one I delete. This is so annoying- (I have over 400 Christmas songs I won't need until n

Music on my iPhone has become very difficult to edit since upgrading to 5.0.1. If I simply want to delete some songs, it insists on a complete sync cycle after EACH one I delete. This is so annoying… (I have over 400 Christmas songs I won't need until next year) I have also noticed it randomly keeps updating album artwork…adding more time to each sync. Is there some way I can turn off the syncing until I have picked and deleted all the songs I want?

The cause was probably a USB glitch during a sync or when copying. The music resides on the phone in separate files. A master file contains a database with an index to the music, an entry for each track and a "pointer" to the file containing the track. Somehow the index got corrupted with duplicate entries. It's likely that the music itself wasn't duplicated, but some tracks had more than one entry in the database. I've seen this happen when syncing (rather than manually managing) also. In my case deleting the track from the Music tab in iTunes, syncing, then adding it back fixed it.
A related problem I've seen is an album may be split, with some tracks in each of 2 or more album entries in the listing. Fixed the same way.

*sigh* My phone has become PUK locked and I have no idea how. PLEASE someone helpe me.

As the title states, my Droid 2 Global has become Pin Unlock Code locked and I'm not sure how. I was going through the process of locking it, and the screen went black halfway through the process and locked itself.
So, I called Verizon...
They said my only choice is to take it to a store to fix it. The closest store is a 2-hour drive and I won't be able to get there until about 6 days from the writing on this post. Does anyone have any ideas of how to fix it? I tried the last 4 digits of my number, and "40" as the customer service lady suggested, but nothing has worked. I don't know that I can do witihout a phone for a week lol.

Well, I looked through the forums and found a thread where someone else had the same exact problem. So, I called the number given and was walked through a solution
Thanks to everyone who looked at the thread

I have contribute 2, edit has become locked on 1 site other 2 ok

Similar Messages

Maybe you are looking for