I have hardware diagnostice failure message

I have an HP Pavilion 6310 with Windows 7 64 bit. The device has been locking up and running very slowly at times. Today, got an error/failure message during hardware diagnostics maintenance program, "SMART Short Self Test SD 521-2W. Any idea what may be happening?

Hi
The Smart DST failure is in regards to the Hard drive or Memory Failure on your unit you will need to replace the part in order to get the unit back to working condition. As per your notes you need to check if that was Hard drive or Memory test which has failed.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Similar Messages

Need an Explanation for an Failure ID from Hardware Diagnostics-8440p

Hello,
i have an hp 8440p and got the Problem that the Primary Battery is suddenly not charging. Worked perfectly the other day.
I tried a suggested solution in this forum where the acpi control method battery in the hardware device manager has to be uninstalled. That did not work.
I started the HP Battery Check under Windows and i got no errors.
When i used the HP Hardware Diagnostics, i've got the following informations:
Failure-ID:6br0GJ-50c78p-x87r5g-c0f003
As my notebook is not covered under warranty(i think), i have no way to contact hp Support.
Which would be perfect, would be if anybody could tell me what has happened to the battery, if i have to replace it and how to avoid such errors.
The current Current of the Battery is:0mA
And just out of curiosity: The HP Battery Check shows under Cycles : 243/300. Does this mean it only had around 60 charging cycles left? <- This would really ease the pain of buying a new battery.
Thanks for your time and your answers.

Hi,
Firstly the good news is battery can "live" much more than that, it still can be in good condition at 600 cycles. And the bad news is that 24 character failed-id tells you the HDD on your machine is failing. Please backup file and data, ready for a HDD replacement.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

HT1976 i have iphone 3gs 8gb when i put sim then i got sim failure message or no sim card installed how to resolve it?

i have iphone 3gs 8gb when i put sim then i got sim failure message or no sim card installed how to resolve it?

Put in a supported SIM from the carrier that locked the iPhone.

How do I send files from my IMAC via bluetooth to my ne Ipad. They will not "pair" but they are connected and discoverable. I send a file from Imac snow leopard OS X 10.6 to the ipad but the failure message says the ipad does not have the ncessary servr

How do I send files from my IMAC via bluetooth to my new Ipad? They will not "pair" but they are connected and discoverable. I send a file from Imac snow leopard OS X 10.6 to the ipadusing bluetooth, but the failure message says the ipad does not have the necessary services. What are these? Do I neeed to have iphoto and ms word to send pix and .doc files?

File Sharing over Bluetooth is not a feature of iOS devices. iOS does not include the required Bluetooth profiles to allow this. You cannot add this feature, so you may as well stop trying.

When I run my hardware diagnostics I'm getting failures - WDC-WD64-00AAKS-65A7B2 SATA DISK DEVICE.

When I run my hardware diagnostics I'm getting failures - WDC-WD64-00AAKS-65A7B2 SATA DISK DEVICE,
HD535-5W, HD535-3W, HD535-2W.
Thanks!!!

That means exactly what it's telling you, the hard drive has failed or is about to fail and needs replacement.
If the system still runs backup your data and create Recovery DVDs ASAP if you haven't already done so.

Mail delivery failure messages for email I have not sent to contacts I do not know.

I am receiving Mail delivery failure messages for emails I have not sent; they are addressed to contacts I've never heard of, many different. Apparently, this is some kind of spam but I don't know what to do about it.

There is nothing you can do about it. It will stop at some point.
http://en.wikipedia.org/wiki/Backscatter_%28email%29

Since installing OS X Yosemite recovery update v.1 on 10/04/15 I have had "Back-up failure" messages. Last successful back-up was 10/04/15 before update. Any suggestions?

Since installing:
a) OS X Yosemite Recovery update v.1; b) OS X Update v.10.10.3 & c) iTunes v.12.1.2 on 10/04/15I have been getting this message.
"Back up Failed - There is not enough space on Time Machine Backup"
The last successful back-up was on the 10/04/15 presumably just prior to these new updates.
Any suggestions?

Time Machine automatically deletes old snapshots to make room for new ones, but it won't delete the last previous snapshot of any disk.
Are you storing any other data on the backup volume, or have you ever backed up another disk or computer to it that you no longer have? If the answer to both these questions in "no," then there isn't enough space on the volume for all the data you want to back up.
If you are storing other data, or if you have backups of a volume you no longer need, you should move or delete that data to make room for more. Alternatively, put the device aside and start a new backup on another storage device. When you're sure you'll no longer need the data on the first device, erase it and start over.

Running hardware diagnostics with Yosemite on iMac

I'd like to run Hardware Diagnostics on a 2011 (maybe 2012) iMac. Yosemite is installed.
Have disconnected everything except keyboard and mouse, shutdown, and tried starting up with the "D" key held down. With this option, the system boots normally....no diagnostics options.
Tried with Shift D, and system boots in safe mode.
Help, please. Thanks!

Thanks for the reply, Mike.
The disk has never been erased to my knowledge, although OSX has been updated with each new release. Perhaps an old DVD with Snow Leopard might have the AHT utility? But will it still run under Yosemite? Is it safe to give it a try?
We're having 2 problems, and was hoping AHT could help rule out a hardware problem. Our primary problem is that Logic Pro (up to date version) intermittently stops and gives a message that the system is too slow. This severely impacts our ability to use the product during recording sessions. Another problem is that we intermittently get a flashing pink and green checkerboard of pixels ...sometimes about 1 inch square, and sometimes as large as 6 inches square (GPU?) (This issue doesn't seem to be creating any file corruption, to the best of our knowledge.)
The iMac is a 27 inch model 11,3. We have 8GB of memory, which, when looking at Activity Monitor, usually indicates only 6.5 GB are being used. Disk utility hasn't revealed any disk problems. (A similar system is using about 7.8 GB, and has no similar problems with Logic). Disk is about 66% full.
If we could rule out hardware issues, we'd try to reinstall Logic Pro, and, perhaps, Yosemite.
Thanks for your help!

Hardware Diagnostics for W700ds

Do the new Lenovo hardware diagnostics tools work with W700ds? This model is not included in the list of supported hardware.
If not, where can I download the previously supported PC-Doctor diagnostics?
I tried the new (unsupported) boot diagnostics on W700ds 2757CTO. Had a few error messages while the linux kernel booted but seemed OK until it looks like the diagnostics tried to switch from text to graphics mode. Display flashed briefly then after a bit more disk activity, nothing further happened. Perhaps the dual screen is not supported?

If your iMac is late 2011 or later, you have built-in diagnostics. Boot with the 'D' key.
If your iMac is older, you should have received diagnostics on the pre bundled installer disc which will boot with the 'D' key.
If you are missing those discs, call AppleCare, and they will ship them for a nominal fee.

Error Oxc18a0001..print failure message

I get an error print failure message and I have followed the troubleshooting steps in the manuel, but that didn't work. What else can I do to try and solve this issue.

OK I had the hp error code 0xc18a0001 problem and here is the conversation I had with the tech.....
james cowan: hp error code 0xc18a0001
Earnest: I will assist you in this regard
james cowan: great
Earnest: I understand that a error code with 0xc18a0001 with "Ink System failure" is displayed on the front panel of the All-In-One printer. Am I correct?
james cowan: correct
Earnest: Thank you for confirmation
Earnest: May I have the model number of All-In-One you are using?
james cowan: c6250
Earnest: Thank you for information.
Earnest: James, please let me know the room temperature in which printer is replaced
james cowan: 67 degrees f
Earnest: Okay
Earnest: Please perform the below steps on the front panel of the printer to resolve the issue
james cowan: ok
Earnest: Press and hold the "left arrow" key.
Press the "Setup" key and release both keys, Display should say "Enter Special Key Combo"
Press and release the "OK" button.
Earnest: Please ignore the above steps, James
james cowan: ok yes nothing seemed to do anything
Earnest: Please perform the below steps on the front panel of the printer
Earnest: Press and Hold the "Print Photos" &"Red Eye Removal" buttons. Release both buttons. Display should say"Enter Special Key Combo"
Press and release in sequence"Red Eye Removal","Print Photos","Red Eye Removal"
Earnest: Display should say “Support” and display the FW rev (something like R0616R)
james cowan: COxxFN0723BR
Earnest: Okay
Earnest: 2. Press and release the right arrow button until the display says “System Configuration Menu
james cowan: ok
Earnest: 3. Press and release the "OK" button.
james cowan: ok and it says hardware failure status
Earnest: Display should say "Hardware failure status: Clear. Press OK to clear".
Earnest: Press and release the "OK" Button. Message changes to "Hardware failure status Cleared. Press Cancel to continue".
Earnest: Press and release the "CANCEL" button as many times as necessary, so that, either the "Welcome to Photosmart Express" screen appears, or, the "Ink System Failure" screen appears. PLEASE DO NOT TRY TO PRINT AT THIS STAGE.
james cowan: ok
Earnest: Using the Power Button, turn the unit OFF and unplug the power cable from back of the printer and wall outlet.
Earnest: Let me know once you are done with the above steps
james cowan: ok its unplugged
Earnest: Wait 30 seconds for the power to get discharged and then plug the power cable into the wall outlet first and then into the back of the printer
Earnest: Turn the unit on. The printer may display message "USE POWER BUTTON TO SHUTDOWN THE PRINTER" followed by "PRESS OK TO CONTINUE". Press OK.
james cowan: ok
Earnest: Let me know the message displaying on the front panel of the printer
james cowan: printer preparation occuring - do not interrupt
Earnest: Okay
james cowan: ok its done
Earnest: Let us print a self test page from the printer now
james cowan: ok deal
Earnest: 1) Load letter, A4, or legal unused plain, white paper into the input tray.
2) Make sure that the printer is on and loaded with unused plain, white paper.
3) Press Setup . The Setup menu appears.
4) Press the down arrow button to select Tools , and then press OK .
5) Press the down arrow button to select Self-test Report , and press OK . The self-test report prints.
james cowan: ok printing
Earnest: Okay, please check whether all the colors pritned perfectly on the test page
james cowan: perfect
Earnest: Great..Cheers!!!
james cowan: thank you very much
Earnest: James, now you can continue using the printer
tecnical support for hp printing

HARDWARE DIAGNOSTICS UEFI. BIOS 1.6.00. AND CHACKING THE MEMORY OF LAPTOP.

I HAVE A HP PAVILION INTEL I3 SERIGE LAPTOP. AT THE TIME OF BOOTING SHOWS A MESSAGE THAT HARDWARE DIAGNOSTICS UEFI. BIOS 1.6.00. AND CHACKING THE MEMORY OF LAPTOP. HOW I GET SOLUTION TO NORMALY RUN LAPTOP? AND ANOTHER PROBLEM IS -= BRIGHTNESS ALOWAS BEING MINIMISED.

Hello SUJOYMONDAL,
Welcome to the HP Forums!
I understand the computer is having a memory and brightness issue. I can do my best to help! I need you to clarify the issues, and please provide the following information:
1. The computer's model number. If you require assistance locating this information, please reference this website: Guide to finding your notebook product number
2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
3. Have you installed any new software or drivers on this computer, before the issue appeared?
Additionally, if the issue just began occurring, I would perform a system restore. I want you to bring the computer back to the earliest restore point possible, in an attempt to dodge whatever caused the issue. Here is a document on how to perform a System Restore: System Restore
Mario
I worked on behalf of HP.

Can not connect to the App store I keep getting a connection failure message. Mail and Safari are working fine. Also Iphoto wont update to newer version and itunes does open up properly.

I have recently bought a new imac. Imported all my files etc. from my G5 using Timemachine.
Iphoto requires updating but wont!
itunes wont open up properly the text is wrong!!
I keep getting a connection failure message when trying to visit the App store.
Safari and Mail are working fine.
My Apple Id is also fine as it works with my ipad.
Any suggestions?

Hello Ben, see if this might be it...
Anonymous
Post subject: NSURLErrorDomain error -1100 in OS X 10.8
If you check for software updates using the App Store in OS X 10.8 and get "NSURLErrorDomain error -1100" the problem may be with your Software Update preferences. This is particularly likely if you were using a custom Apple Software Update server. To solve the problem, quit the App Store, move the following two files (if present) to the trash, restart, and only then rerun App Store updates:
/Library/Preferences/com.apple.SoftwareUpdate.plist
/Library/Preferences/com.apple.SoftwareUpdate.plist.lockfile
http://x704.net/bbs/viewtopic.php?f=12&t=6130

Canon iR C2380i Failure Message

Hi,
I'm trying to setup my laptop so I can print wireless via a Canon iR C2380i. I'm running OS X 10.6.7 on a MacBook Pro i5.
The problem is when I'm trying to print a document, I get the failure message "AN ERROR OCCURRED.: -50" and then a print with the same message is printed.
I'm using the PS v3.20 driver as I read this would be the best to use.
Anyone has an idea what to do?
Thanks,
Mads

Hello and welcome to Apple Discussions.
The -50 error can occur when you have selected the wrong IP protocol when creating the print queue. The PS v3 and UFR2 v2 drivers prefer the LPD protocol. If you created the IP queue using IPP then this can cause the error. So if you did select IPP for the protocol, then delete the current queue and add it again, this time selecting IP > LPD.
The cause of the error can be that the copier does not support the printer language of the driver being used. I agree that PS is the best driver to use but you need to ensure that the copier does support this print language. You can confirm this by opening a web browser and typing the IP address of the iR C2380. This will open the internal web page of the copier, called Remote UI. With this open, down the left column you will see a variety of buttons. Select the one that says Add Func (short for Additional Functions). In the expanded list then select Custom Settings. Now in the right pane you should see the heading of Printer Settings. Under this will be the protocols supported. You will see UFRII but you also want to see PS (short for Postscript). If you don't see PS then you will have to use the UFRII driver on the Mac. The latest version, 2.24, resolves an issue with OS X 10.6.7 where the document would not print due to the default Quality Setting.
If the iR C2380i does have Postscript and changing the PS driver print queue to LPD still causes an error then I may need some more information about the network setup. You mention using wireless. Do you know if the iR C2380i is connecting via Ethernet to the same wireless router that the Mac is using?

Mac Pro Dual Quad Xeon 2.66, Lion, weird pattern on display, then died. Won't reboot. Did hardware diagnostics, says no problem. Video screen still has weird pattern, see apple, spins no boot. HELP!

Gee...I didn't know I was going to get a whole box to describe the problem. We took it apart, checked memory, it's ok. When I pried open the dvd and started from the install disc to run the hardware diagnostics, I pressed d. It didn't give me a choice about hard discs to start from, I have a snow leopard bootable disc ad a lion bootable disc. It didn't even see them.
I have work to do! Freakin.
So, it chimes, shows the apple with the pattern all over the screen and it spins, and then you see a progress bar. it doesn't go any further.

Take the card out and boot the machine.
The hit one of the volume up/down keys on keyboad. If you here the usual sound, it booted.
With any luck you have Screen Sharing enabled and can remotely log in.
But reaching desktop with the card out is pretty much proof that card is gone.
8800GT is black with 2 silver arrow shapes.
You can try removing heatsink (12 screws) and baking it. (google)
You have exacty NOTHING to lose, so 50/50 odds are worth a shot.

Need to send success or failure message to BAPI of SQL query action block

Hi All,
I need to send success or failure message(i.e. 1 or 0) to BAPI which has been called below sql query action block in transaction
Here in SAP, i have created on BAPI with one import parameter and one export parameter.
In the sql query action block, it insert records in the database table. If it fail or success, that message(numeric value 1 or 0) has to send to SAP program through BAPI.
I have created a SAP ABAP program which sends message to MII Message listener through RFC then in the process rule message it will call transaction, in transaction, sql query will insert records into database table. if it success or fail, it will pass to BAPI. And i calling that BAPI in the same SAP ABAP Program to show in the output screen.
Here the issues, i am not getting the value from BAPI which has send by the transaction in MII.
SAP Jco, I have mapped in conf. links --> BAPI input with sql query sucess
Thanks,
Kind Regards,
Praveen Reddy M

Dear All,
I am facing problem regarding completion notifications in Oraclr r12, when user click the upon completion generated notifications it can only be viewd once, second time user cannot view the notifications.
I have find that fnd_file_temp table store this information and deleted it.
Plz help me how to view this URL again.
thanks
regards,
Zubyr

I have hardware diagnostice failure message

Similar Messages

Maybe you are looking for